-- ***************************************************************** -- DLINKES-POE-MIB.mib : D-Link extensions to POWER-ETHERNET-MIB (PoE) -- -- Copyright (c) 2013 D-Link Corporation, all rights reserved. -- -- ***************************************************************** DLINKES-POE-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP FROM SNMPv2-CONF MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Unsigned32 FROM SNMPv2-SMI DisplayString,TruthValue FROM SNMPv2-TC InetAddressType, InetAddress FROM INET-ADDRESS-MIB PortList, VlanId FROM Q-BRIDGE-MIB pethMainPseGroupIndex, pethPsePortIndex, pethPsePortShortCounter, pethPsePortOverLoadCounter, pethPsePortPowerDeniedCounter FROM POWER-ETHERNET-MIB dlinkCommon FROM DLINK-ID-REC-MIB; dlinkEsPoeExtMIB MODULE-IDENTITY LAST-UPDATED "202011300000Z" ORGANIZATION "D-Link Corp." CONTACT-INFO " D-Link Corporation Postal: No. 289, Sinhu 3rd Rd., Neihu District, Taipei City 114, Taiwan, R.O.C Tel: +886-2-66000123 E-mail: tsd@dlink.com.tw " DESCRIPTION "A MIB module for extending POWER-ETHERNET-MIB specified in RFC 3621. " REVISION "202011300000Z" DESCRIPTION "Add PoE Guard Band." REVISION "201810090000Z" DESCRIPTION "Add pd alive tables to support PD alive check feature." REVISION "201305290000Z" DESCRIPTION "Initial version of this MIB module." ::= { dlinkCommon 24 } -- ----------------------------------------------------------------------------- esPoeMIBNotifications OBJECT IDENTIFIER ::= { dlinkEsPoeExtMIB 0 } esPoeMIBObjects OBJECT IDENTIFIER ::= { dlinkEsPoeExtMIB 1 } esPoeMIBConformance OBJECT IDENTIFIER ::= { dlinkEsPoeExtMIB 2 } -------------------------------------------------------------------------------- esPoeGroupCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF EsPoeGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table consists of a list of group configurations for PoE. Group means box in the stack or module in a rack. For non-modular devices, the pethMainPseGroupIndex is 1. " ::= { esPoeMIBObjects 1 } esPoeGroupCfgEntry OBJECT-TYPE SYNTAX EsPoeGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains the system configuration of the PoE on a group." INDEX { pethMainPseGroupIndex } ::= { esPoeGroupCfgTable 1 } EsPoeGroupCfgEntry ::= SEQUENCE { esPoeGroupPolicyPreempt TruthValue, esPoeGroupClearIfStatistic PortList, esPoeGroupGuardBand Unsigned32 } esPoeGroupPolicyPreempt OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures whether to disconnect the PD which is powered with lower priority in order to release the power to the new connected PD with higher priority under power shortage condition. If this object is 'false', then the policy is first in first serviced. Thus the new PD will not be serviced if the power budget is running out. If this object is 'true', then the power provisioned to PD with lower priority can be preempted to release the power to the new connected PD with higher priority. " DEFVAL { false } ::= { esPoeGroupCfgEntry 1 } esPoeGroupClearIfStatistic OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to clear the PoE statistics of pethPsePortEntry for specified ports. " ::= { esPoeGroupCfgEntry 2 } esPoeGroupGuardBand OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliwatts" MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the amount of power to be preserved for guard band protection. The PoE guard-band can provide protection PoE enabled ports from being powered off and then ON when there is a sudden spike in the consumed power of PDs. The specified amount of guard band power is preserved to provide the regulation during sudden spike in the consumed power of PDs." ::= { esPoeGroupCfgEntry 3 } ------------------------------------------------------------------------------- esPoeGroupInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF EsPoeGroupInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table consists of a list of PoE information for groups." ::= { esPoeMIBObjects 2 } esPoeGroupInfoEntry OBJECT-TYPE SYNTAX EsPoeGroupInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains the system information of the PoE on a group." INDEX { pethMainPseGroupIndex } ::= { esPoeGroupInfoTable 1 } EsPoeGroupInfoEntry ::= SEQUENCE { esPoeGroupMaxPorts Integer32, esPoeGroupHWVersion DisplayString, esPoeGroupSWVersion DisplayString } esPoeGroupMaxPorts OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of ports that the group can support." ::= { esPoeGroupInfoEntry 1 } esPoeGroupHWVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates H/W version of PoE chip." ::= { esPoeGroupInfoEntry 2 } esPoeGroupSWVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates firmware version of PoE chip." ::= { esPoeGroupInfoEntry 3 } -------------------------------------------------------------------------------- esPoeIfObjects OBJECT IDENTIFIER ::= { esPoeMIBObjects 3 } esPoeIfCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF EsPoeIfCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table consists of a list of PoE configuration information for ports." ::= { esPoeIfObjects 1 } esPoeIfCfgEntry OBJECT-TYPE SYNTAX EsPoeIfCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains PoE configuration on a port." INDEX { pethMainPseGroupIndex, pethPsePortIndex } ::= { esPoeIfCfgTable 1 } EsPoeIfCfgEntry ::= SEQUENCE { esPoeIfState INTEGER, esPoeIfMaxPower Integer32, esPoeIfTimeRange DisplayString, esPoeIfLegacyPdEnabled TruthValue } esPoeIfState OBJECT-TYPE SYNTAX INTEGER { auto(1), never(2), static(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the PoE state of the entry. auto(1) - the port will automatically detect the PD and provision power to the PD. The max wattage value which can be provisioned to the port is determined by esPoeIfMaxPower. If esPoeIfMaxPower is unspecified, then the class of the PD auto determines the maximum wattage which can be provisioned. The PD will not be provisioned if it requests more wattage than the max wattage which is determined. never(2) - indicates the port will not supply power to connected PD; static(3) - indicates manager pre-allocate power budget to the port by configuring the esPoeIfMaxPower object. The power budget is allocated to the port even though there is no PD connected to the port. If esPoeIfMaxPower is not configured, default value is 15400mW for 802.3af and 30000mW for 802.3at." DEFVAL {auto} ::= { esPoeIfCfgEntry 1 } esPoeIfMaxPower OBJECT-TYPE SYNTAX Integer32( 0 | 1000..30000) UNITS "milliwatts" MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the max wattage value which can be provisioned to the port. Note: This object is valid only while the esPoeIfState object is configured as auto or static." ::= { esPoeIfCfgEntry 2 } esPoeIfTimeRange OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the name of time-range profile to delineate the activation period. A zero length string indicates the time-range is not specified. Note: This object is valid only while the esPoeIfState is 'auto'." ::= { esPoeIfCfgEntry 3 } esPoeIfLegacyPdEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the state of legacy PD support." DEFVAL { false } ::= { esPoeIfCfgEntry 4 } -------------------------------------------------------------------------------- esPoeIfInfoObjects OBJECT IDENTIFIER ::= { esPoeIfObjects 2 } esPoeIfStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF EsPoeIfStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table consists of a list of PoE status for ports." ::= { esPoeIfInfoObjects 1 } esPoeIfStatusEntry OBJECT-TYPE SYNTAX EsPoeIfStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry consists of PoE status for a port." INDEX { pethMainPseGroupIndex,pethPsePortIndex } ::= { esPoeIfStatusTable 1 } EsPoeIfStatusEntry ::= SEQUENCE { esPoeIfDetectStatus INTEGER, esPoeIfFaultyType INTEGER, esPoeIfPowerClassifications INTEGER, esPoeIfOperMaxPower Unsigned32, esPoeIfOperOutputPower Unsigned32, esPoeIfOperDescription DisplayString } esPoeIfDetectStatus OBJECT-TYPE SYNTAX INTEGER { disabled(1), searching(2), requesting(3), delivering(4), faulty(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the operational status of the port PD detection. disabled(1) - PSE function is disabled. searching(2) - Remote PD is not connected. requesting(3) - Remote PD is inserted, but the PSE doesn't provide power yet. delivering(4) - Remote PD is now powering by PoE system. faulty(5) - Device detection or a powered device is in a faulty state. " ::= { esPoeIfStatusEntry 1 } esPoeIfFaultyType OBJECT-TYPE SYNTAX INTEGER { notApplicable(0), mpsAbsent(1), pdShort(2), overload(3), powerDenied(4), thermalShutdown(5), startupFailure(6), classificationFailure(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the specific faulty type. It is meaningful only when esPoeIfDetectStatus object is 'faulty'. notApplicable(0) - indicates this object is meaningless, e.g. the esPoeIfDetectStatus is not 'faulty'. mpsAbsent(1) - indicates MPS(Maintain Power Signature) Absent pdShort(2) - indicates PD Short overload(3) - indicates Overload powerDenied(4) - indicates Power Denied thermalShutdown(5)- indicates Thermal Shutdown startupFailure(6) - indicates Startup Failure classificationFailure(7) - indicates Classification Failure(IEEE 802.3at) " ::= { esPoeIfStatusEntry 2 } esPoeIfPowerClassifications OBJECT-TYPE SYNTAX INTEGER { none(0), class0(1), class1(2), class2(3), class3(4), class4(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Classification is a way to tag different terminals on the Power over LAN network according to their power consumption. Devices such as IP telephones, WLAN access points and others, will be classified according to their power requirements. The meaning of the classification labels is defined in the IEEE specification. This variable is valid only while a PD is being powered, that is, while the attribute pethPsePortDetectionStatus is reporting the enumeration deliveringPower." ::= { esPoeIfStatusEntry 3 } esPoeIfOperMaxPower OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum power of the port." ::= { esPoeIfStatusEntry 4 } esPoeIfOperOutputPower OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliwatts" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the output power of the port." ::= { esPoeIfStatusEntry 5 } esPoeIfOperDescription OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the description for the port." ::= { esPoeIfStatusEntry 6 } -------------------------------------------------------------------------------- esPoeIfMeasurementTable OBJECT-TYPE SYNTAX SEQUENCE OF EsPoeIfMeasurementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table consists of a list of POE measurement information for ports." ::= { esPoeIfInfoObjects 2 } esPoeIfMeasurementEntry OBJECT-TYPE SYNTAX EsPoeIfMeasurementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry consists of PoE measurement information of a port." INDEX { pethMainPseGroupIndex, pethPsePortIndex } ::= { esPoeIfMeasurementTable 1 } EsPoeIfMeasurementEntry ::= SEQUENCE { esPoeIfVoltage Integer32, esPoeIfCurrent Integer32, esPoeIfTemperature Integer32, esPoeIfPower Integer32 } esPoeIfVoltage OBJECT-TYPE SYNTAX Integer32 UNITS "millivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the voltage of the port in millivolts." ::= { esPoeIfMeasurementEntry 1 } esPoeIfCurrent OBJECT-TYPE SYNTAX Integer32 UNITS "milliamperes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current of port in milliamperes." ::= { esPoeIfMeasurementEntry 2 } esPoeIfTemperature OBJECT-TYPE SYNTAX Integer32 UNITS "Degree Centigrade" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the temperature of port in degrees centigrade." ::= { esPoeIfMeasurementEntry 3 } esPoeIfPower OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates consumption power of port in milliwatts." ::= { esPoeIfMeasurementEntry 4 } -------------------------------------------------------------------------------- esPoeIfStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF EsPoeIfStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table consists of a list of POE statistics information for ports." ::= { esPoeIfInfoObjects 3 } esPoeIfStatisticsEntry OBJECT-TYPE SYNTAX EsPoeIfStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry consists of PoE statistics information of a port." INDEX { pethMainPseGroupIndex, pethPsePortIndex } ::= { esPoeIfStatisticsTable 1 } EsPoeIfStatisticsEntry ::= SEQUENCE { esPoeIfStatMpsAbsent Integer32, esPoeIfStatOverload Integer32, esPoeIfStatShort Integer32, esPoeIfStatPowerDenied Integer32, esPoeIfStatInvalidSignature Integer32 } esPoeIfStatMpsAbsent OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the MPS absent counter." ::= { esPoeIfStatisticsEntry 1 } esPoeIfStatOverload OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the overload counter." ::= { esPoeIfStatisticsEntry 2 } esPoeIfStatShort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the short counter." ::= { esPoeIfStatisticsEntry 3 } esPoeIfStatPowerDenied OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the power denied counter." ::= { esPoeIfStatisticsEntry 4 } esPoeIfStatInvalidSignature OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the invalid signature counter." ::= { esPoeIfStatisticsEntry 5 } -------------------------------------------------------------------------------- esPoeIfPdAliveCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF EsPoeIfPdAliveCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table consists of a list of configuration for the PD alive check function for ports. The PD alive check feature provides the solution for PD device that has the stop working or no response problem via Ping mechanism. Detailed Process: The detailed processes are described as follows: 1. The system needs to periodically monitor the specific PD by using Ping function. If there is no response, system takes one of the following actions: (1) Reset: Switch resets (disable then enable) PoE power on the port which connects to a PD under monitoring. (2) Notify: Switch sends logs and traps to notify the administrator. (3) Both: Switch sends logs and traps, and resets the PoE port power. 2. The system should implement the retry mechanism to check PD aliveness, hence the system will reset the PoE port power feeding after the retry by using Ping without any response from a PD. 3. If the action is Reset or Both, the system needs to wait for PD recovery from rebooting and then executes the Ping function again. Besides, the waiting time can be configured by users. 4. If PoE schedule (time range) function is configured on the port which enables the PD Alive Check function, the time range function has the top priority, and therefore PD Alive Check function will not work while PoE time range function is still active. 5. This function only takes effect on PoE enabled port with power feeding. Note: It is required to setup IP settings properly that the PD can be reachable for Ping, otherwise this function cannot work as expected. Limitation 1. Support Ping Function: If the PD does not support ICMP, this function cannot work normally. 2. Direct-Connected PD: The Reset Action can only work on the direct-connected PD. If the PD is not connected directly, the Reset Action may not work as expected. 3. PD Also Acts as PSE: If the direct-connected PD is also a PSE, all the next level PDs connect to this PSE will be power cycling whenever PD Alive Check function takes effect on 'Reset' or 'Both' Action." ::= { esPoeIfObjects 3 } esPoeIfPdAliveCfgEntry OBJECT-TYPE SYNTAX EsPoeIfPdAliveCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains configuration for PD alive check on a port." INDEX { pethMainPseGroupIndex, pethPsePortIndex } ::= { esPoeIfPdAliveCfgTable 1 } EsPoeIfPdAliveCfgEntry ::= SEQUENCE { esPoeIfPdAliveCfgState INTEGER, esPoeIfPdAliveCfgPdIpType InetAddressType, esPoeIfPdAliveCfgPdIpAddr InetAddress, esPoeIfPdAliveCfgInterval Unsigned32, esPoeIfPdAliveCfgRetry Unsigned32, esPoeIfPdAliveCfgWaitTime Unsigned32, esPoeIfPdAliveCfgAction INTEGER, esPoeIfPdAliveCfgResidentialVlan VlanId } esPoeIfPdAliveCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the the PD alive function sate. enabled - Enable the PD alive check function disabled - Disable the PD alive check function." DEFVAL { disabled } ::= { esPoeIfPdAliveCfgEntry 1 } esPoeIfPdAliveCfgPdIpType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the IP address type of the target PD." ::= { esPoeIfPdAliveCfgEntry 2 } esPoeIfPdAliveCfgPdIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the IP address of the target PD." ::= { esPoeIfPdAliveCfgEntry 3 } esPoeIfPdAliveCfgInterval OBJECT-TYPE SYNTAX Unsigned32 (10..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the time interval for system issues ping request to detect the target PD. The valid range for interval time is 10s to 300s." DEFVAL { 30 } ::= { esPoeIfPdAliveCfgEntry 4 } esPoeIfPdAliveCfgRetry OBJECT-TYPE SYNTAX Unsigned32 (0..5) UNITS "times" MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the retry count of ping request when PD has no response. The valid range for retry count is 0 to 5 times." DEFVAL { 2} ::= { esPoeIfPdAliveCfgEntry 5 } esPoeIfPdAliveCfgWaitTime OBJECT-TYPE SYNTAX Unsigned32 (30..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the waiting time for PD reboot. The valid range for waiting time is 30s to 300s." DEFVAL { 90 } ::= { esPoeIfPdAliveCfgEntry 6 } esPoeIfPdAliveCfgAction OBJECT-TYPE SYNTAX INTEGER { reset(1), notify(2), both(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the action when PD doesn't reply the ping request. reset- System will reset the PoE port state . notify- System will send log and trap to notify the administrator. both- System will send log and trap first and reset the PoE port state." DEFVAL { both } ::= { esPoeIfPdAliveCfgEntry 7 } esPoeIfPdAliveCfgResidentialVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the VLAN identifier (VID) of the source IP interface dedicated for ICMP messages. The specific VID of the IP interface is only used for IPv6 ICMP messages." ::= { esPoeIfPdAliveCfgEntry 8 } -- ***************************************************************************** -- MIB Notifications -- ***************************************************************************** esPoeIfPowerDeniedNotification NOTIFICATION-TYPE OBJECTS { pethPsePortPowerDeniedCounter } STATUS current DESCRIPTION " This Notification indicates if PSE state diagram enters the state POWER_DENIED. At least 500 msec must elapse between notifications being emitted by the same object instance." ::= { esPoeMIBNotifications 1 } esPoeIfPowerOverLoadNotification NOTIFICATION-TYPE OBJECTS { pethPsePortOverLoadCounter } STATUS current DESCRIPTION " This Notification indicates if PSE state diagram enters the state ERROR_DELAY_OVER. At least 500 msec must elapse between notifications being emitted by the same object instance." ::= { esPoeMIBNotifications 2 } esPoeIfPowerShortCircuitNotification NOTIFICATION-TYPE OBJECTS { pethPsePortShortCounter } STATUS current DESCRIPTION " This Notification indicates if PSE state diagram enters the state ERROR_DELAY_SHORT. At least 500 msec must elapse between notifications being emitted by the same object instance." ::= { esPoeMIBNotifications 3 } esPoeIfPdAliveFailOccurNotification NOTIFICATION-TYPE OBJECTS { pethMainPseGroupIndex, pethPsePortIndex, esPoeIfPdAliveCfgPdIpType, esPoeIfPdAliveCfgPdIpAddr } STATUS current DESCRIPTION " This Notification indicates if the PD device has the stop working or no response problem." ::= { esPoeMIBNotifications 4 } -- ***************************************************************************** -- MIB Conformance statements -- ***************************************************************************** esPoeMIBCompliances OBJECT IDENTIFIER ::= { esPoeMIBConformance 1 } esPoeMIBGroups OBJECT IDENTIFIER ::= { esPoeMIBConformance 2 } esPoeMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the DLINKES-POE-MIB." MODULE -- this module MANDATORY-GROUPS { esPoeGroupCfgGroup, esPoeIfCfgGroup, esPoeGroupInfoGroup, esPoeIfInfoGroup, esPoeIfErrorStateNotificationGroup, esPoeIfPdAliveCfgGroup } ::= { esPoeMIBCompliances 1 } esPoeGroupCfgGroup OBJECT-GROUP OBJECTS { esPoeGroupPolicyPreempt, esPoeGroupGuardBand } STATUS current DESCRIPTION "A collection of objects to configure or display the group-specific PoE information." ::= { esPoeMIBGroups 1 } esPoeIfCfgGroup OBJECT-GROUP OBJECTS { esPoeGroupClearIfStatistic, esPoeIfState, esPoeIfMaxPower, esPoeIfTimeRange, esPoeIfLegacyPdEnabled } STATUS current DESCRIPTION "A collection of objects configure or display the ports information." ::= { esPoeMIBGroups 2 } esPoeGroupInfoGroup OBJECT-GROUP OBJECTS { esPoeGroupMaxPorts, esPoeGroupHWVersion, esPoeGroupSWVersion } STATUS current DESCRIPTION "A collection of objects display the groups information." ::= { esPoeMIBGroups 3 } esPoeIfInfoGroup OBJECT-GROUP OBJECTS { esPoeIfDetectStatus, esPoeIfFaultyType, esPoeIfPowerClassifications, esPoeIfOperMaxPower, esPoeIfOperOutputPower, esPoeIfOperDescription, esPoeIfVoltage, esPoeIfCurrent, esPoeIfTemperature, esPoeIfPower, esPoeIfStatMpsAbsent, esPoeIfStatOverload, esPoeIfStatShort, esPoeIfStatPowerDenied, esPoeIfStatInvalidSignature } STATUS current DESCRIPTION "A collection of objects display the ports information." ::= { esPoeMIBGroups 4 } esPoeIfErrorStateNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { esPoeIfPowerDeniedNotification, esPoeIfPowerOverLoadNotification, esPoeIfPowerShortCircuitNotification, esPoeIfPdAliveFailOccurNotification } STATUS current DESCRIPTION "A collection of objects provides ports error state notifications." ::= { esPoeMIBGroups 5 } esPoeIfPdAliveCfgGroup OBJECT-GROUP OBJECTS { esPoeIfPdAliveCfgState, esPoeIfPdAliveCfgPdIpType, esPoeIfPdAliveCfgPdIpAddr, esPoeIfPdAliveCfgInterval, esPoeIfPdAliveCfgRetry, esPoeIfPdAliveCfgWaitTime, esPoeIfPdAliveCfgAction, esPoeIfPdAliveCfgResidentialVlan } STATUS current DESCRIPTION "A collection of objects display the PD alive check configuration." ::= { esPoeMIBGroups 6 } END