2007-05-23
This MIB Augments the POWER-ETHERNET-MIB created by the IETF Ethernet Interfaces and Hub MIB Working Group for managing Power Source Equipment (PSE). The objects in this MIB are intended to provide additional objects for reporting information available to the hardware on this platform which are not represented in the draft MIB.
Download BROADCOM-POWER-ETHERNET-MIB.txt Open BROADCOM-POWER-ETHERNET-MIB.txt in a new tab
END OF TOC
1.3.6.1.4.1.4526.10.15.1.1
augments pethPsePortTable (POWER-ETHERNET-MIB)
Index: pethPsePortGroupIndex · pethPsePortIndex
A table of per-port information and configuration objects relating to the power status of each port.
from POWER-ETHERNET-MIB
Integer32 (1..2147483647)
This variable uniquely identifies the group containing the port to which a power Ethernet PSE is connected. Group means box in the stack, module in a rack and the value 1 MUST be used for non-modular devices. Furthermore, the same value MUST be used in this variable, pethMainPseGroupIndex, and pethNotificationControlGroupIndex to refer to a given box in a stack or module in the rack.
Integer32 (1..2147483647)
This variable uniquely identifies the power Ethernet PSE port within group pethPsePortGroupIndex to which the power Ethernet PSE entry is connected.
1.3.6.1.4.1.4526.10.15.1.1.1.1
Gauge32 · Milliwatts
The configured maximum power this port can provide to an attached device measured in Milliwatts.
1.3.6.1.4.1.4526.10.15.1.1.1.2
Gauge32 · Milliwatts
The power this port is supplying to an attached device measured in Milliwatts.
1.3.6.1.4.1.4526.10.15.1.1.1.3
Gauge32 · Milliamps
The current this port is supplying to an attached device measured in Milliamps.
1.3.6.1.4.1.4526.10.15.1.1.1.4
Gauge32 · Millivolts
The voltage this port is supplying to an attached device measured in millivolts.
1.3.6.1.4.1.4526.10.15.1.1.1.5
Gauge32 · DEGREES
The temperature measured at this port of the PoE Controller. It is measured in degree celcius.
1.3.6.1.4.1.4526.10.15.1.1.1.6
INTEGER1 = dot3af2 = user3 = none · Integer32
Reference: Broadcom 5910X programmers guide, IEEE Std 802.3af Section 30.9.1.1.6
Describes or controls the maximum power that a port can deliver A value of dot3af(1) means that the port power limit is as per the dot3af class of the PD attached. A value of user(2) means that the port power limit is equal to the value specified by agentPethPowerLimit
1.3.6.1.4.1.4526.10.15.1.1.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Reference: Broadcom 5910X programmers guide
true (1) The PSE port can deliver power up to 32Watts. false(2) The PSE port can deliver power up to 18Watts
1.3.6.1.4.1.4526.10.15.1.1.1.8
INTEGER0 = none1 = legacy2 = fourPtdot3afonly3 = fourPtdot3afandlegacy4 = twoPtdot3afonly5 = twoPtdot3afandlegacy · Integer32
Reference: Broadcom 5910X programmers guide, IEEE Std 802.3af Section 30.9.1.1.6
Describes PD detection mechanism performed by the PSE port. A value of none(0) means no detection is done. A value of legacy(1) means only legacy capacitive detection scheme is used. A value of 4ptdot3afonly(2) means that IEEE 802.3af 4point detection scheme is used. A value of 4ptdot3afandlegacy(3)means that IEEE 802.3af 4point detection scheme is used and when that fails to detect a connected PD, legacity capacitive detection is used. A value of 2ptdot3afonly(4) means that IEEE 802.3af 2point detection scheme is used. A value of 2ptdot3afandlegacy(5)means that IEEE 802.3af 2point detection scheme is used and when that fails to detect a connected PD, legacity capacitive detection is used. The value 'none' can not be forcibly set by the administrator.
1.3.6.1.4.1.4526.10.15.1.1.1.9
INTEGER0 = none1 = mpsAbsent2 = short3 = overload4 = powerDenied · Integer32
Reference: Broadcom 5910X programmers guide, IEEE Std 802.3af
Describes the error description when the pse port is in fault status. A value of none(0) specifies that the pse port is not in any error state. A value of mpsAbsent(1) specifies that the pse port has detected and absence of main power supply. A value of short(2) specifies that the pse port has detected a short circuit condition. A value of overload(3) specifies that the pd connected to the pse port had tried to draw more power than permissible by the hardware. A value of powerDenied(4) specifies that the pse port has been denied power because of shortage of power or due to administrative action.
1.3.6.1.4.1.4526.10.15.1.1.1.10
INTEGER0 = none1 = reset · Integer32
Reference: Broadcom 5910X programmers guide, IEEE Std 802.3af
A value of reset(1) is used to move the pse port dot3af state to idle. A read on this object will always return the value none(0). The value none(0) can not be forcibly set by the administrtor.
1.3.6.1.4.1.4526.10.15.1.1.1.11
INTEGER0 = ieee802dot3af1 = high-inrush2 = pre-802dot3at3 = ieee802dot3at · Integer32
Reference: Broadcom 5910X programmers guide, Command 0x1C
Describes the power up mode used by the PSE Port. A value of 802dot3af(0) means port is powered in IEEE 802.3af mode. A value of high-inrush(1) means port is powered used high-inrush current, used by legacy PD's A value of pre-802dot3at(2) means port is powered in IEEE 802.3af mode initially, switched to high-power IEEE 802.3at mode before 75msec. This mode needs to be used if PSE is NOT performing Layer 2 Classification Or PSE is performing 2-Event Layer 1 Classification. A value of 802dot3at(3) means is port is powered in IEEE 802.3at mode. i.e. if class detected by PSE is not class4 then PSE port will not power up the PD.
1.3.6.1.4.1.4526.10.15.1.1.1.12
INTEGER0 = bypass1 = standard · Integer32
Reference: Broadcom 5910X programmers guide, Command 0x11
Describes the classification mode used by the PSE Port. A value of bypass(0) means port is not performing classification. A value of standard(1) means port is performing classification as per IEEE 802.3af/802.3at .
1.3.6.1.4.1.4526.10.15.1.2.1
augments pethMainPseTable (POWER-ETHERNET-MIB)
Index: pethMainPseGroupIndex
A table of objects that display and control attributes of the main power source in a PSE device. Ethernet switches are one example of boxes that would support these objects. Values of all read-write objects in this table are persistent at restart/reboot.
from POWER-ETHERNET-MIB
Integer32 (1..2147483647)
This variable uniquely identifies the group to which power Ethernet PSE is connected. Group means (box in the stack, module in a rack) and the value 1 MUST be used for non-modular devices. Furthermore, the same value MUST be used in this variable, pethPsePortGroupIndex, and pethNotificationControlGroupIndex to refer to a given box in a stack or module in a rack.
1.3.6.1.4.1.4526.10.15.1.2.1.1.1
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Enable/Disable Legacy device detection. The value true(1) means legacy devices are detected; the value false(2) means legacy devices are not detected.
1.3.6.1.4.1.4526.10.15.1.3
augments pethMainPseTable (POWER-ETHERNET-MIB)
Index: pethMainPseGroupIndex
A table of per-unit information and configuration objects relating to the power configurtion for the entire pse unit.
from POWER-ETHERNET-MIB
Integer32 (1..2147483647)
This variable uniquely identifies the group to which power Ethernet PSE is connected. Group means (box in the stack, module in a rack) and the value 1 MUST be used for non-modular devices. Furthermore, the same value MUST be used in this variable, pethPsePortGroupIndex, and pethNotificationControlGroupIndex to refer to a given box in a stack or module in a rack.
1.3.6.1.4.1.4526.10.15.1.3.1.1
INTEGER1 = static2 = dynamic · Integer32
Reference: Broadcom 5910X programmers guide
Describes or controls the power management algorithm used by the pse to deliver power to the requesting PDsthat a pds.
1.3.6.1.4.1.4526.10.15.1.3.1.2
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
true (1) The PSE port is reset with out administrator intervention whenver a fault condition occurs. false(2) Administrator has to reset the pse port whenver a fault condition is detected.