2002-12-18
The MIB for providing information specified in ITU Q752 Monitoring and Measurements for Signalling System No. 7(SS7) Network. This information can be used to manage messages transported over SS7 Network via Cisco IP Transfer Point. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 signaling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7.
Download CISCO-ITP-ACT-MIB.txt Open CISCO-ITP-ACT-MIB.txt in a new tab
| Name | OID |
|---|---|
| cItpActMtp3Table | 1.3.6.1.4.1.9.9.230.1.1.1 |
| cItpActGttTable | 1.3.6.1.4.1.9.9.230.1.2.1 |
END OF TOC
1.3.6.1.4.1.9.9.230.1.1.1
Index: cItpActMtp3TableId · cItpActMtp3LinksetName · cItpActMtp3Dpc · cItpActMtp3Opc · cItpActMtp3SI
This table contains information about the number of packets and bytes at the MTP3 layer. The information collected from both directions(send and receive). The information is broken down by linkset, Destination Point Code (DPC), Originating Point Code (OPC) and Signalling Indicator (SI). This provides the lowest granularity required by Q752 and allows network management stations to calculate the required fields in Q752.
1.3.6.1.4.1.9.9.230.1.1.1.1.1
INTEGER1 = passed2 = violation · Integer32
The accounting table identifier. 'passed' : signifies that this table instance represents statistics for packets that matched an Access Control List (ACL) in the linkset's inbound ACL and in the outbound ACL. 'violation' : signifies that this table instance represents statistics for packets that did not match an ACL in the linkset's inbound ACL and in the outbound ACL.
1.3.6.1.4.1.9.9.230.1.1.1.1.2
CItpTcLinksetIdThe configured name associated with an Signalling Point Linkset. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (1..19) · OCTET STRING
The name of the linkset.
1.3.6.1.4.1.9.9.230.1.1.1.1.3
CItpTcPointCodeThe SS7 network node address as specified in the following references. The format of the Point code depends on the variant defined in the CgspSS7Variant object as follows. 33222222222211111111110000000000 10987654321098765432109876543210 ANSI: nnnnnnnn - Network cccccccc - Cluster mmmmmmmm - Member ITU: zzz - Zone aaaaaaaa - Area/Network iii - Identifier NTT: zzzzz - Zone aaaa - Area/Network iiiiiii - Identifier TTC: zzzzz - Zone aaaa - Area/Network iiiiiii - Identifier Note: The China variant has the same format as ANSI. This form of the point-code is not intended for for presentation.Reference: The SS7 network node address as specified in the International Telecommunication Union standard Q.708: Specifications of Signalling System No. 7 - Numbering of International Signalling Point Codes, and by ANSI T1.111.8 Numbering of Signalling Point Codes. GF 001-9001 - Technical Specifications of Signalling System No. 7 for National Telephone Network of China. (0..16777216) · Unsigned32
The destination point code.
1.3.6.1.4.1.9.9.230.1.1.1.1.4
CItpTcPointCodeThe SS7 network node address as specified in the following references. The format of the Point code depends on the variant defined in the CgspSS7Variant object as follows. 33222222222211111111110000000000 10987654321098765432109876543210 ANSI: nnnnnnnn - Network cccccccc - Cluster mmmmmmmm - Member ITU: zzz - Zone aaaaaaaa - Area/Network iii - Identifier NTT: zzzzz - Zone aaaa - Area/Network iiiiiii - Identifier TTC: zzzzz - Zone aaaa - Area/Network iiiiiii - Identifier Note: The China variant has the same format as ANSI. This form of the point-code is not intended for for presentation.Reference: The SS7 network node address as specified in the International Telecommunication Union standard Q.708: Specifications of Signalling System No. 7 - Numbering of International Signalling Point Codes, and by ANSI T1.111.8 Numbering of Signalling Point Codes. GF 001-9001 - Technical Specifications of Signalling System No. 7 for National Telephone Network of China. (0..16777216) · Unsigned32
The origin point code.
1.3.6.1.4.1.9.9.230.1.1.1.1.5
CItpTcServiceIndicator0 = snmm1 = sntm2 = spare23 = sccp4 = tup5 = isup6 = dupc7 = dupf8 = mtup9 = bisup10 = sisup11 = spare1112 = spare1213 = spare1314 = spare1415 = spare15The list of possible Service Indicator values. This identifies the type of SS7 packet. The service indicator codes for the international Signalling network are allocated as follows: 'SNMM' : Signalling network management messages (SNMM) 'SNTM' : Signalling network testing and maintenance messages (SNTM) 'Spare2' : Spare 2 'SCCP' : SCCP 'TUP' : Telephone User Part (TUP) 'ISUP' : ISDN User Part (ISUP) 'DUPC' : Data User Part, call and circuit-related messages (DUPC) 'DUPF' : Data User Part, facility registration and cancellation messages (DUPF) 'MTUP' : Reserved for MTP Testing User Part (MTUP) 'BISUP' : Broadband ISDN User Part (BISUP) 'SISUP' : Satellite ISDN User Part (SISUP) 'Spare11' : Spare 11 'Spare12' : Spare 12 'Spare13' : Spare 13 'Spare14' : Spare 14 'Spare15' : Spare 15Reference: ITU Q.704 Signalling network functions and messages section 14.2.1 Service indicator. · Integer32
The service indicator.
1.3.6.1.4.1.9.9.230.1.1.1.1.6
Counter32 · packets
Sum of all received packets for this linkset, DPC and OPC combination.
1.3.6.1.4.1.9.9.230.1.1.1.1.7
Counter32 · packets
Sum of all transmitted packets for this linkset, DPC and OPC combination.
1.3.6.1.4.1.9.9.230.1.1.1.1.8
Counter32 · bytes
Sum of all received bytes for this linkset, DPC and OPC combination.
1.3.6.1.4.1.9.9.230.1.1.1.1.9
Counter32 · bytes
Sum of all transmitted bytes for this linkset, DPC and OPC combination.
1.3.6.1.4.1.9.9.230.1.2.1
Index: cItpActGttLinksetName · cItpActGttSelectorName · cItpActGttGta · cItpActGttTranslatedPc
This table contains information about the number of packets and bytes required for global title translation.
1.3.6.1.4.1.9.9.230.1.2.1.1.1
CItpTcLinksetIdThe configured name associated with an Signalling Point Linkset. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (1..19) · OCTET STRING
The name of the linkset.
1.3.6.1.4.1.9.9.230.1.2.1.1.2
CItpTcGlobalTitleSelectorNameThe configured name associated with SCCP GTT Selector. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (1..9) · OCTET STRING
The Global Title Selector Name.
1.3.6.1.4.1.9.9.230.1.2.1.1.3
CItpTcGtaAddrThe configured digits in the SCCP GTT Global Title Address. An octet string specified by an administrator must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (8) · OCTET STRING
The Global Title Address.
1.3.6.1.4.1.9.9.230.1.2.1.1.4
CItpTcPointCodeThe SS7 network node address as specified in the following references. The format of the Point code depends on the variant defined in the CgspSS7Variant object as follows. 33222222222211111111110000000000 10987654321098765432109876543210 ANSI: nnnnnnnn - Network cccccccc - Cluster mmmmmmmm - Member ITU: zzz - Zone aaaaaaaa - Area/Network iii - Identifier NTT: zzzzz - Zone aaaa - Area/Network iiiiiii - Identifier TTC: zzzzz - Zone aaaa - Area/Network iiiiiii - Identifier Note: The China variant has the same format as ANSI. This form of the point-code is not intended for for presentation.Reference: The SS7 network node address as specified in the International Telecommunication Union standard Q.708: Specifications of Signalling System No. 7 - Numbering of International Signalling Point Codes, and by ANSI T1.111.8 Numbering of Signalling Point Codes. GF 001-9001 - Technical Specifications of Signalling System No. 7 for National Telephone Network of China. (0..16777216) · Unsigned32
The translated point code.
1.3.6.1.4.1.9.9.230.1.2.1.1.5
Counter32 · bytes
Number of packets performing Global Title Translation.
1.3.6.1.4.1.9.9.230.1.2.1.1.6
Counter32 · bytes
Count of bytes received that required Global Title Translation.