The MIB for providing information specified in ITU Q752 Monitoring and Measurements for Signalling System No. 7(SS7) Network. This information can be used to manage messages transported over SS7 Network via Cisco IP Transfer Point.
The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 signalling point.
The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7.
Reference: GR-82-CORE 6.4.7 Special Study Measurements
This table contains information about the number of packets and bytes at the MTP3 transport layer. The information collected from both directions(send and receive). The information is broken down by linkset, Destination Point Code (DPC), Originating Point Code (OPC) and Signalling Indicator (SI). This provides the lowest granularity required by Q752 and allows network management stations to calculate the required fields in Q752.
CItpTcNetworkNameThe network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network.
When multiple instance support is not enable the network name will default to the null string.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (0..19) · OCTET STRING
The network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network. When multiple instance support is not enabled the network name will default to the null string.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space.
The accounting table identifier.
'passed' : signifies that this table instance
represents statistics for packets that matched an Access Control List (ACL) in the linkset's inbound ACL and in the outbound ACL.
'violation' : signifies that this table instance represents statistics for packets that did not match an ACL in the linkset's inbound ACL and in the outbound ACL.
'unroutable' : packets that pass access list verification but can not be sent to destination point code. This could be caused by incorrect or missing route statements or inaccessible destination.
cgactMtp3LinksetName
1.3.6.1.4.1.9.9.333.1.1.1.1.2
CItpTcLinksetIdThe configured name associated with an Signalling Point Linkset.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (1..19) · OCTET STRING
The name of the linkset.
cgactMtp3Dpc
1.3.6.1.4.1.9.9.333.1.1.1.1.3
CItpTcPointCodeThe SS7 network node address as specified in the following references. The format of the Point code depends on the variant defined in the CgspSS7Variant object as follows.
33222222222211111111110000000000 10987654321098765432109876543210
ANSI: nnnnnnnn - Network
cccccccc - Cluster
mmmmmmmm - Member
ITU: zzz - Zone
aaaaaaaa - Area/Network
iii - Identifier
NTT: zzzzz - Zone
aaaa - Area/Network
iiiiiii - Identifier
TTC: zzzzz - Zone
aaaa - Area/Network
iiiiiii - Identifier
Note: The China variant has the same format as ANSI.
This form of the point-code is not intended for for presentation.Reference: The SS7 network node address as specified in the International Telecommunication Union standard Q.708: Specifications of Signalling System No. 7 - Numbering of International Signalling Point Codes, and by ANSI T1.111.8 Numbering of Signalling Point Codes.
GF 001-9001 - Technical Specifications of Signalling System No. 7 for National Telephone Network of China. (0..16777216) · Unsigned32
The destination point code.
cgactMtp3Opc
1.3.6.1.4.1.9.9.333.1.1.1.1.4
CItpTcPointCodeThe SS7 network node address as specified in the following references. The format of the Point code depends on the variant defined in the CgspSS7Variant object as follows.
33222222222211111111110000000000 10987654321098765432109876543210
ANSI: nnnnnnnn - Network
cccccccc - Cluster
mmmmmmmm - Member
ITU: zzz - Zone
aaaaaaaa - Area/Network
iii - Identifier
NTT: zzzzz - Zone
aaaa - Area/Network
iiiiiii - Identifier
TTC: zzzzz - Zone
aaaa - Area/Network
iiiiiii - Identifier
Note: The China variant has the same format as ANSI.
This form of the point-code is not intended for for presentation.Reference: The SS7 network node address as specified in the International Telecommunication Union standard Q.708: Specifications of Signalling System No. 7 - Numbering of International Signalling Point Codes, and by ANSI T1.111.8 Numbering of Signalling Point Codes.
GF 001-9001 - Technical Specifications of Signalling System No. 7 for National Telephone Network of China. (0..16777216) · Unsigned32
The origin point code.
cgactMtp3SI
1.3.6.1.4.1.9.9.333.1.1.1.1.5
CItpTcServiceIndicator0 = snmm1 = sntm2 = spare23 = sccp4 = tup5 = isup6 = dupc7 = dupf8 = mtup9 = bisup10 = sisup11 = spare1112 = spare1213 = spare1314 = spare1415 = spare15The list of possible Service Indicator values. This identifies the type of SS7 packet.
The service indicator codes for the international Signalling network are allocated as follows:
'SNMM' : Signalling network management
messages (SNMM)
'SNTM' : Signalling network testing and
maintenance messages (SNTM)
'Spare2' : Spare 2
'SCCP' : SCCP
'TUP' : Telephone User Part (TUP)
'ISUP' : ISDN User Part (ISUP)
'DUPC' : Data User Part, call and circuit-related
messages (DUPC)
'DUPF' : Data User Part, facility registration and
cancellation messages (DUPF)
'MTUP' : Reserved for MTP Testing User Part (MTUP)
'BISUP' : Broadband ISDN User Part (BISUP)
'SISUP' : Satellite ISDN User Part (SISUP)
'Spare11' : Spare 11
'Spare12' : Spare 12
'Spare13' : Spare 13
'Spare14' : Spare 14
'Spare15' : Spare 15Reference: ITU Q.704 Signalling network functions and messages section 14.2.1 Service indicator. · Integer32
The service indicator.
cgactMtp3InPackets
1.3.6.1.4.1.9.9.333.1.1.1.1.6
Counter32 · packets
The accumulated number of packets that have been received by this linkset, DPC and OPC combination since system startup.
cgactMtp3OutPackets
1.3.6.1.4.1.9.9.333.1.1.1.1.7
Counter32 · packets
The accumulated number of packets that have been sent using this linkset, DPC and OPC combination since system startup.
cgactMtp3InOctets
1.3.6.1.4.1.9.9.333.1.1.1.1.8
Counter32 · octets
The accumulated number of bytes that have been received using this linkset, DPC and OPC combination since system startup.
cgactMtp3OutOctets
1.3.6.1.4.1.9.9.333.1.1.1.1.9
Counter32 · octets
The accumulated number of bytes that have been sent using this linkset, DPC and OPC combination since system startup.
This table has been deprecated and replaced with cgactGtt2Table table.
This table contains information about the number of packets and octets required for global title translation.
CItpTcNetworkNameThe network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network.
When multiple instance support is not enable the network name will default to the null string.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (0..19) · OCTET STRING
The network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network. When multiple instance support is not enabled the network name will default to the null string.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space.
cgactGttLinksetName
1.3.6.1.4.1.9.9.333.1.2.1.1.1
CItpTcLinksetIdThe configured name associated with an Signalling Point Linkset.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (1..19) · OCTET STRING
The name of the linkset.
cgactGttSelectorName
1.3.6.1.4.1.9.9.333.1.2.1.1.2
CItpTcGlobalTitleSelectorNameThe configured name associated with SCCP GTT Selector.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (1..9) · OCTET STRING
The Global Title Selector Name.
cgactGttGta
1.3.6.1.4.1.9.9.333.1.2.1.1.3
CItpTcGtaLongAddrThe configured hexadecimal digits in the SCCP GTT Global Title Address. SIZE (0..64) · OCTET STRING
The Global Title Address.
cgactGttTranslatedPc
1.3.6.1.4.1.9.9.333.1.2.1.1.4
CItpTcPointCodeThe SS7 network node address as specified in the following references. The format of the Point code depends on the variant defined in the CgspSS7Variant object as follows.
33222222222211111111110000000000 10987654321098765432109876543210
ANSI: nnnnnnnn - Network
cccccccc - Cluster
mmmmmmmm - Member
ITU: zzz - Zone
aaaaaaaa - Area/Network
iii - Identifier
NTT: zzzzz - Zone
aaaa - Area/Network
iiiiiii - Identifier
TTC: zzzzz - Zone
aaaa - Area/Network
iiiiiii - Identifier
Note: The China variant has the same format as ANSI.
This form of the point-code is not intended for for presentation.Reference: The SS7 network node address as specified in the International Telecommunication Union standard Q.708: Specifications of Signalling System No. 7 - Numbering of International Signalling Point Codes, and by ANSI T1.111.8 Numbering of Signalling Point Codes.
GF 001-9001 - Technical Specifications of Signalling System No. 7 for National Telephone Network of China. (0..16777216) · Unsigned32
The translated point code.
cgactGttPackets
1.3.6.1.4.1.9.9.333.1.2.1.1.5
Counter32 · packets
The accumulated number of packets received by this signalling point requiring global title translation since system startup.
cgactGttOctets
1.3.6.1.4.1.9.9.333.1.2.1.1.6
Counter32 · octets
The accumulated number of bytes received by this signalling point requiring global title translation since system startup.
CItpTcNetworkNameThe network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network.
When multiple instance support is not enable the network name will default to the null string.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (0..19) · OCTET STRING
The network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network. When multiple instance support is not enabled the network name will default to the null string.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space.
cgactGtt2LinksetName
1.3.6.1.4.1.9.9.333.1.2.2.1.1
CItpTcLinksetIdThe configured name associated with an Signalling Point Linkset.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (1..19) · OCTET STRING
The name of the linkset.
cgactGtt2SelectorName
1.3.6.1.4.1.9.9.333.1.2.2.1.2
CItpTcGlobalTitleSelectorNameThe configured name associated with SCCP GTT Selector.
An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. SIZE (1..9) · OCTET STRING
The Global Title Selector Name.
cgactGtt2Gta
1.3.6.1.4.1.9.9.333.1.2.2.1.3
CItpTcGtaLongAddrThe configured hexadecimal digits in the SCCP GTT Global Title Address. SIZE (0..64) · OCTET STRING
The Global Title Address.
cgactGtt2TranslatedInstNumber
1.3.6.1.4.1.9.9.333.1.2.2.1.4
CItpTcInstanceNumberThe instance number used to select a particular Signalling point. (0..255) · Unsigned32
The instance number used to define in which network the translated point-code resides.
cgactGtt2TranslatedPc
1.3.6.1.4.1.9.9.333.1.2.2.1.5
CItpTcPointCodeThe SS7 network node address as specified in the following references. The format of the Point code depends on the variant defined in the CgspSS7Variant object as follows.
33222222222211111111110000000000 10987654321098765432109876543210
ANSI: nnnnnnnn - Network
cccccccc - Cluster
mmmmmmmm - Member
ITU: zzz - Zone
aaaaaaaa - Area/Network
iii - Identifier
NTT: zzzzz - Zone
aaaa - Area/Network
iiiiiii - Identifier
TTC: zzzzz - Zone
aaaa - Area/Network
iiiiiii - Identifier
Note: The China variant has the same format as ANSI.
This form of the point-code is not intended for for presentation.Reference: The SS7 network node address as specified in the International Telecommunication Union standard Q.708: Specifications of Signalling System No. 7 - Numbering of International Signalling Point Codes, and by ANSI T1.111.8 Numbering of Signalling Point Codes.
GF 001-9001 - Technical Specifications of Signalling System No. 7 for National Telephone Network of China. (0..16777216) · Unsigned32
The translated point code.
cgactGtt2Packets
1.3.6.1.4.1.9.9.333.1.2.2.1.6
Counter32 · packets
The accumulated number of packets received by this signalling point requiring global title translation since system startup.
cgactGtt2Octets
1.3.6.1.4.1.9.9.333.1.2.2.1.7
Counter32 · octets
The accumulated number of bytes received by this signalling point requiring global title translation since system startup.