CISCO-MEMORY-POOL-MIB

CiscoMemoryPoolTypesRepresents the different types of memory pools that may be present in a managed device. Memory pools can be roughly categorized into two groups, predefined pools and dynamic pools. The following pool types are currently predefined: 1: processor memory 2: i/o memory 3: pci memory 4: fast memory 5: multibus memory Dynamic pools will have a pool type value greater than any of the predefined types listed above. Note that only the processor pool is required to be supported by all devices. Support for other pool types is dependent on the device being managed. (1..65535) · Integer32

The type of memory pool for which this entry contains information.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

A textual name assigned to the memory pool. This object is suitable for output to a human operator, and may also be used to distinguish among the various pool types, especially among dynamic pools.

Integer32 (0..65535)

Indicates whether or not this memory pool has an alternate pool configured. Alternate pools are used for fallback when the current pool runs out of memory. If an instance of this object has a value of zero, then this pool does not have an alternate. Otherwise the value of this object is the same as the value of ciscoMemoryPoolType of the alternate pool.

TruthValue1 = true2 = falseRepresents a boolean value. · Integer32

Indicates whether or not the remaining objects in this entry contain accurate data. If an instance of this object has the value false (which in and of itself indicates an internal error condition), the values of the remaining objects in the conceptual row may contain inaccurate information (specifically, the reported values may be less than the actual values).

Gauge32 · bytes

Indicates the number of bytes from the memory pool that are currently in use by applications on the managed device.

Gauge32 · bytes

Indicates the number of bytes from the memory pool that are currently unused on the managed device. Note that the sum of ciscoMemoryPoolUsed and ciscoMemoryPoolFree is the total amount of memory in the pool

Gauge32 · bytes

Indicates the largest number of contiguous bytes from the memory pool that are currently unused on the managed device.

PercentAn integer that is in the range of a percent value. (0..100) · Integer32

This object is used to indicate the threshold value in percentage of free memory remaining in a memory pool. If the free memory available goes below this threshold value and if ciscoMemoryPoolLowMemoryNotifEnable is set to 'true', ciscoMemoryPoolLowMemoryNotif will be generated. When the available free memory comes back to the threshold value ciscoMemoryPoolLowMemoryRecoveryNotif will be generated.

PercentAn integer that is in the range of a percent value. (0..100) · Integer32

This is the memory pool utilization for 1 minute.

PercentAn integer that is in the range of a percent value. (0..100) · Integer32

This is the memory pool utilization for 5 minutes.

PercentAn integer that is in the range of a percent value. (0..100) · Integer32

This is the memory pool utilization for 10 minutes.