CISCO-MMODAL-CONTACT-APPS-MIB

Integer32 (1..1000)

An arbitrary integer, selected by the local Device, which uniquely identifies a Device within the cluster.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

The Host name of the Device in the Cluster.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

The description for the device which can include additional information regarding the device.

INTEGER1 = runtime2 = reporting3 = unknown · Integer32

The Device type. runtime(1) : The device is a runtime device. reporting(2): The device is a reporting server device. unknown(3) : The type of the remote device is not known.

INTEGER1 = unknown2 = local3 = remoteup4 = remotedown · Integer32

The current status of the remote Device as viewed by this device. A remote device is up if the local device can communicate with it. unknown(1) : Current status of the remote device is Unknown, local (2) : This is the local device in the table, remote-up(3) : The local device is running and is able to communicate with the remote device. remote-down(4): The local device is running but it is unable to communicate with the remote Device.

InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention. ipv4z(3) A non-global IPv4 address including a zone index as defined by the InetAddressIPv4z textual convention. ipv6z(4) A non-global IPv6 address including a zone index as defined by the InetAddressIPv6z textual convention. dns(16) A DNS domain name as defined by the InetAddressDNS textual convention. Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType. To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32

This object identifies the IP address type of the remote device.

InetAddressDenotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row. The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING

This object identifies ip address of the remote device. The type of address for this is identified by InetAddressType.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

The unique ID of the Cluster to which this device belongs. At any point in time, the Cluster Id helps in associating a device to any given Cluster.

Integer32 (1..1000)

An arbitrary integer, selected by the local device used to identify the neighbouring node.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

The name of the node that is connected to the device.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

A string describing the type of node that is connected to the device. This can be Unknown, ICM(PG), CUPS.

InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention. ipv4z(3) A non-global IPv4 address including a zone index as defined by the InetAddressIPv4z textual convention. ipv6z(4) A non-global IPv6 address including a zone index as defined by the InetAddressIPv6z textual convention. dns(16) A DNS domain name as defined by the InetAddressDNS textual convention. Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType. To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32

This object identifies the IP address type of the neighbouring node connected to the device.

InetAddressDenotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row. The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING

This object identifies ip address of the neighbouring node connected to the device. The type of address for this is identified by cmmcaNextNodeIpAddrType.

CmmcaNextNodeStatus1 = unknown2 = available3 = unavailableThis textual convention is used to identify the link status of a neighbouring node with a CUEA Device. 'unknown' The status of the link is unknown to the SNMP agent either because the link between the agent and the application has been broken or the agent is in the midst of refreshing link status. (A refresh typically occurs after an agent restart due to configuration changes.) 'available' The connection between the neighbouring node and CUEA device is up and available. 'unavailable' The connection between the neighbouring node and CUEA device is down and unavailable. · Integer32

The current status of the neighbouring node connected to the device as viewed by this Device. unknown(1) : Current status of the node is Unknown, available (2) : The connection is up and available unavailable(3) : The connection is down and not available.

Integer32 (1..1000)

An arbitrary integer, selected by the local device used to identify the System Condition.

Integer32 (1..2147483647)

An unique Id of the System Condition used to identify a specific System Condition.

CmmcaConditionStatus1 = conditionWarn2 = conditionCriticalThis textual convention is used to specify the severity of a specific system condition raised by CUEA or services in it. CUEA can run with certain system conditions raised. The overall system condition status of the application is specified by CmmcaSystemConditionStatus. conditionWarn(1) : This severity level indicates a warning that something is not right, however the application is still functioning, but the condition may be indicative of problem that may become more serious later. conditionCritical(2): This serverity indicates a condition where the application is not functioning properly. · Integer32

This object specifies the severity level of the raised condition.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

This object provides a breif description of the raised System Condition.

DateAndTimeA date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. SIZE (8 | 11) · OCTET STRING · hint 2d-1d-1d,1d:1d:1d.1d,1a1d:1d

The timestamp of when the Condition was raised.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

This object provides a message about the event which resulted in the System Condition being raised.

CmmcaIndexAn arbitrary value which uniquely identifies a service. The value should be a small positive integer; index values for different services are not necessarily contiguous. (1..4294967295) · Unsigned32

The service index is a value that uniquely identifies an entry in the service table. The value is arbitrarily assigned by the SNMP agent.

CmmcaServiceType1 = cm2 = rm3 = wa4 = mpa5 = bre6 = icmgw7 = rda8 = ra9 = rsThis textual convention is used to identify the type of service. The Cisco Unified Expert Advisor includes one or but probably multiple, of the following services. 'cm': Contact Manager: The Contact manager service is responsible for the handling of call requests and maintaining contact state. CM uses BRE to help direct call flow decision making. The major services that the CM interfaces with are the Work Assigner (WA), Media Platform Interface (MPA), Knowledge Broker (KB), the ICM Gateway (GW), and Business Rules Execution Engine (BRE). 'rm': Resource Manager: The Resource Manager (RM) is responsible for maintaining the state of assignable resources, e.g. agents. The RM interfaces to the Work Assigner, Media Platform Interface, Resource Desktop Adapter and Business Rules Engine. 'wa': Work assigner: The Work Asssigner is responsible for matching Contacts that need Resources with Resources that need Contacts. 'mpa': Media Platform Adapter: The Media Platform Adapter is a generic interface to various switching and call control platforms. Removes inconsistencies and normalizes messages before sending them. It is an SIP Back to Back user Agent, providing basic third party call control and end point functions to its clients(RM,CM,RDA). 'bre': Business Rules Engine: The BRE allows customers to define how the system will behave and then execute scripts or business rules at runtime. 'icmgw': ICM Gateway : The ICM Gateway talks to the ERS PG of ICM over the GED-188 (ACMI) protocol. It sends agent state information to the ICM so that the ICM knows whether or not to route calls. 'rda': Resource Desktop Adapter: This service is used by RM to communicate to the user interface of the Resource(Agent). It provides a normalized interface (RDI) to the RM that removes differences between communicating to different types of desktops or Resources viz;CTI-OS, Presence, WebBased desktops or Traditional/occasional agents. 'ra': Reporting Adapter: RAs listen to event streams that are produced by runtime components. They then take those events, convert them as appropriate (for example, converting them to a particular version of a schema or applying a security policy of what data can be sent to the reporting database) and then send a new message to the Cisco MMCA Reporting Subsystem. 'rs': Reporting Subsystem: The RS is responsible for writing data into the reporting database. It receives messages from various Reporting Adapters and converts them into db writes. · Integer32

The service type object identifies the type of Cisco Unified Expert Advisor functional service, see CmmcaServiceType Textual convention for more information.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

The service name object is a user-intuitive textual name for the application service.

CmmcaServiceStatus1 = disabled2 = starting3 = inService4 = inServiceWarning5 = inServiceCritical6 = partialService7 = outOfService8 = stopping9 = stopped10 = unknownThis textual convention is used to identify the run status of a Cisco Unified Expert Advisor service. The value shown is the result of evaluating the current run status of each of the individual elements associated with the service. 'disabled' The service has not yet begun to start up. 'starting' The service is in initialization procedure, configuring and licensing, not accepting connections yet. 'inService' The service is up and running optimally, accepting connections at full QoS (if applicable). 'inServiceWarning' The service is running sub-optimally, possibly due to poor QoS or a threshold reached; see transition reason for explanation. 'inServiceCritical' The service is running but very near to failure, similar to 'inServiceWarning' but much more dire. 'partialService' The service is no longer accepting new calls but finishes processing active calls (may be due to a loss of a dependency/ connectivity, or a shutdown request). 'outOfService' The service is no longer accepting new calls and is down for some reason. It can still be brought in service. 'stopping' The service no longer accepts new connections, lets current connections terminate gracefully. 'stopped' The service has shut down and is not processing any more calls. The process itself is terminating (doing memory cleanup, saving settings, shutting down threads, etc.). 'unknown' The status of the mmca service is unknown to the SNMP agent either because the link between the agent and the application has been broken or the agent is in the midst of refreshing service status. (A refresh typically occurs after an agent restart due to configuration changes). · Integer32

The service status object is the last known status of the application service.

Gauge32 (1..1440) · minutes

This object defines the interval window over which values of certain MIB objects of the corresponding service are calculated. Each service entry defined in cmmcaServiceTable has corresponding entries in a related table in cmmcaServiceInfo that are identified by the same index and hence have sparse dependent relationship. For eg: if cmmcaServiceIntPeriod is 30 min for a service of type Reporting Subsystem(rs), then cmmcaRsIntResourceEventDetailRecords interval object in cmmcaRsTable for this service, reports the number of ResourceEventDetailRecords written into the database in the last 30 min interval.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

The routing domain, a descriptive text, that specifies the service is in.

CmmcaSeverityLevel1 = emergency2 = alert3 = critical4 = error5 = warning6 = notice7 = informational8 = debugThis textual convention is used to specify the severity level of an event. The severity levels are 'emergency': This severity level event indicates that a devastating failure has occurred; the system or service is unusable. Immediate operator intervention is required. 'alert': This severity level event indicates that a devastating failure is imminent that will render the system unusable. Immediate operator attention is necessary. 'critical': This severity level event indicates that a service impacting failure is likely to occur soon; an error has occurred that was not appropriately handled by the system. Operator attention is needed as soon as possible. 'error': This severity level event indicates that the system has experienced a temporary impairment or an error that was appropriately handled by the system. 'warning': This severity level event may be a precursor to an error occurrence. An operator should review the event soon to determine if action is needed. 'notice': This severity level event contains health or operational state information that may be pertinent to the health of the system but does not require the attention of the administrator at this time. 'informational': This severity level event contains interesting system-level information that is valuable to an administrator, however, the event itself does not indicate a failure or impairment condition. 'debug': This severity level event provides supplemental information that may be beneficial toward diagnosing or resolving a problem but does not in itself provide operational health status. · Integer32

The current log level of the service. A log level acts as a filter to decide which events will be logged. Hence a log level has the same values as defined in CmmcaSeverityLevel. A log level will enable the service to log events that have atleast the designated severity. For eg: a log level set to warning(5) will only log events that have a level of atleast warning(5) severity; ie; All emergency(1), alert(2), critical(3), error(4), warning(5) events will be logged. 'emergency': This log level indicates that only events of such severity will be logged. . 'alert': This log level indicates that all emergency and alert events will be logged. 'critical': This log level indicates that all emergency, alert and critical events will be logged. 'error': This log level indicates that all emergency, alert, critical and error level events will be logged. 'warning': This log level indicates that all emergency, alert, critical, error and warning events will be logged. 'notice': This log level indicates that all emergency, alert, critical, error, warning and notice level events will be logged. 'informational': This log level indicates that all emergency, alert, critical, error, warning, notice and informational events will be logged. 'debug': This log level indicates that all emergency, alert, critical, error, warning, notice and debug level events will be logged.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

The current trace mask for debugging for the service.

Gauge32 · messages per second

The Average message throughput in messages/sec per service.

Counter64 (0..18446744073709551615) · seconds

The total number of seconds the service has been up.

Counter64 (0..18446744073709551615) · messages

The total number of messages received by the service since application start time specified by cmmcaStartTime.

Unsigned32 · threads

The Maximum number of threads available for this Service.

Gauge32 · threads

Number of threads currently running for this Service.

Gauge32 · agents

The Real Time indicator of the number of agents currently logged in.

Gauge32 · agents

The real Time indicator of the number of agents currently on calls.

Gauge32 · agents

The real Time indicator of the number of agents currently in the reserved state.

Gauge32 · agents

The real Time indicator of the number of agents currently wrapping up a call.

Gauge32 · agents

The real Time indicator of the number of agents currently in the ready state.

Gauge32 · agents

The real Time indicator of the number of agents currently unallocated in any queue (most likely a configuration error).

Counter64 (0..18446744073709551615) · offers

The number of offers accepted since application start time specified by cmmcaStartTime.

Gauge32 · offers

The number of offers accepted over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · offers

The number of offers rejected since application start time specified by cmmcaStartTime.

Gauge32 · offers

The number of offers rejected over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · offers

The number of offers that timed out since application start time specified by cmmcaStartTime.

Gauge32 · offers

The number of offers that timed out over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · calls

The real time indicator of the number of active calls.

Gauge32 · calls

The real time indicator of the number of calls where a contact is created; BRE script is started.

Gauge32 · calls

The real time indicator of the number of calls which are currently receiving ringback.

Gauge32 · calls

The real time indicator of the number of calls where a resource has been identified selected and the call is in the process of being connected.

Gauge32 · calls

The real time indicator of the number of calls in which a contact is connected to one or more participant (e.g., self-service, agents, conference).

Gauge32 · calls

The real time indicator of the number of calls in which a contact is in initial state.

Counter64 (0..18446744073709551615) · calls

Number of new calls which arrived at the Contact Manager since application start time specified by cmmcaStartTime.

Gauge32 · calls

Number of new calls which arrived at the Contact Manager over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · calls

The real time indicator of the number of calls which could not be accepted and processed (e.g. due to invalid call, lack of system resources or licenses, or no agent available) and are currently in the process of being rejected.

Gauge32 · calls

The real time indicator of the number of calls in which participant changes are currently in progress (e.g.,participant adds/removes like conferencing, redirecting or transferring).

Gauge32 · calls

The real time indicator of the number of calls which are currently terminating because all parties but one have disconnected.

Gauge32 · seconds

The average call handling time since application start time specified by cmmcaStartTime.

Gauge32 · seconds

The average call handling time over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Integer32 · seconds

The maximum call handling time since application start time specified by cmmcaStartTime.

Integer32 · seconds

The maximum call handling time over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

DateAndTimeA date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. SIZE (8 | 11) · OCTET STRING · hint 2d-1d-1d,1d:1d:1d.1d,1a1d:1d

The timestamp when the maximum call duration time since application start time, cmmcaStartTime, has occurred.

DateAndTimeA date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. SIZE (8 | 11) · OCTET STRING · hint 2d-1d-1d,1d:1d:1d.1d,1a1d:1d

The timestamp of when the maximum call duration time over the last interval, specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable, occurred.

Gauge32 · seconds

The average call time in queue since application start time specified by cmmcaStartTime.

Gauge32 · seconds

The average call time in queue over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Integer32 · seconds

The maximum call time in queue since application start time specified by cmmcaStartTime.

Integer32 · seconds

The maximum call time in queue over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

DateAndTimeA date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. SIZE (8 | 11) · OCTET STRING · hint 2d-1d-1d,1d:1d:1d.1d,1a1d:1d

The timestamp of when the maximum call time in queue since application start(cmmcaStartTime), occurred.

DateAndTimeA date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. SIZE (8 | 11) · OCTET STRING · hint 2d-1d-1d,1d:1d:1d.1d,1a1d:1d

The timestamp of when the maximum call time in queue over the last interval, specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable, occurred.

Gauge32 · calls per minute

The average call arrival rate since application start time specified by cmmcaStartTime.

Integer32 · calls per minute

The maximum of interval average call arrival rate, displayed by cmmcaCmIntAvgCallArrivalRate, since application start time, specified by cmmcaStartTime.

DateAndTimeA date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. SIZE (8 | 11) · OCTET STRING · hint 2d-1d-1d,1d:1d:1d.1d,1a1d:1d

The timestamp of when the maximum call arrival rate since application start (cmmcaStartTime), occurred.

Gauge32 · calls per minute

The average rate of calls over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · messages

The number of messages processed since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · messages

The number of messages processed over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · notifications

The number of successful presence notifications since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · notifications

The number of successful presence notifications over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · clients

The real time number of active end-user devices that have capability to perform instant message operation.

Gauge32 · tasks

The real time number of outstanding offertasks to be processed.

Counter64 (0..18446744073709551615) · notifications

The number of unsuccessful presence notifications since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · notifications

The number of unsucessful presence notifications over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · clients

The real time number of inactive clients.

Counter32 · scripts

The total number of scripts loaded by the BRE.

Counter32 · scripts

The total number of distinct scripts loaded by the BRE (not including different versions of the same script).

Gauge32 · scripts

The real time number of loaded BRE scripts that are active.

Gauge32 · instances

The current number of script instances existing at this moment in time.

Counter32 · instances

The maximum number of script instances that existed since application start time specified by cmmcaStartTime.

Gauge32 · instances

The maximum number of script instances that existed over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

DateAndTimeA date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. SIZE (8 | 11) · OCTET STRING · hint 2d-1d-1d,1d:1d:1d.1d,1a1d:1d

The timestamp of when the maximum concurrent instances, specified by cmmcaBreAggMaxConcurrentInstances, since application start time (cmmcaStartTime) has occurred.

DateAndTimeA date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. SIZE (8 | 11) · OCTET STRING · hint 2d-1d-1d,1d:1d:1d.1d,1a1d:1d

The timestamp of when the maximum concurrent instances over the last interval, specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable, has occurred.

Gauge32 · instances

The average number of instances being worked on by the BRE since application start time specified by cmmcaStartTime.

Gauge32 · instances

The average number of instances being worked on by the BRE over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · initiations

The total number of script instances created since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · initiations

The total number of script instances created over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · initiations

The total number of contact script instances created since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · initiations

The total number of contact script instances created over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · initiations

The total number of resource script instances created since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · initiations

The total number of resource script instances created over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · terminations

The total number of script instances terminated since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · terminations

The total number of script instances terminated over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · terminations

The total number of contact script instances terminated since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · terminations

The total number of contact script instances terminated over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · terminations

The total number of resource script instances terminated since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · terminations

The total number of resource script instances terminated over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · endings

The total number of script instances that ended abnormally since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · endings

The total number of script instances that ended abnormally over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · endings

The total number of contact script instances that ended abnormally since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · endings

The total number of contact script instances that ended abnormally over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Counter64 (0..18446744073709551615) · endings

The total number of resource script instances that ended abnormally since application start time specified by cmmcaStartTime.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · endings

The total number of resource script instances that ended abnormally over the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · none

The real time number of Assignment Queues configured.

Gauge32 · none

The real time number of Attribute definitions configured.

Gauge32 · none

The real time number of selection strategies configured.

Gauge32 · none

The real time number of skills configured.

Counter64 (0..18446744073709551615) · none

The real time number of errors processing config messages.

Counter64 (0..18446744073709551615) · messages

The total number of CancelResourceRequest messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of ResourceRequest messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of ResourceResponse messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of CancelWorkRequest messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total mumber of OfferTaskAccept messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of OfferTaskCancelled messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of OfferTaskResponse messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of OfferTask messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of ResyncResourceResponseAcknowledgement messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of ResyncResourceResponse received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of ResyncResource messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of WorkRequest messages Received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of QueueEvent messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of WorkRequestCanceled messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of WRIFailureResponse messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of RRIFailureResponseSent messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of ResourceResponseCanceled messages sent since boot time.

Counter64 (0..18446744073709551615) · messages

The total number of CancelQueueEvent messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of times messages could not be sent since application start time specified by cmmcaStartTime.

Gauge32 · criteria

The real time number of resource criteria configured.

Gauge32 · attributes

The real time number of selection strategy attributes configured.

Gauge32 · criteria

The real time number of attribute criteria configured.

Gauge32 · resources

The real time number of resources configured.

Gauge32 · values

The real time number of attribute values configured.

Gauge32 · competencies

The real time number of skill competencies configured.

Gauge32 · members

The real time number of resource members configured.

Gauge32 · resources

The real time number of known total resources.

Gauge32 · contacts

The real time number of total known total contacts.

Gauge32 · services

The real time number of known resource manager services.

Gauge32 · services

The real time number of known contact manager services.

Counter64 (0..18446744073709551615) · calls

The total number of new calls requests received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · connects

The total number of connect attempts since application start time specified by cmmcaStartTime.

Gauge32 · milliseconds

The average time in milliseconds required to complete a connection.

Counter64 (0..18446744073709551615) · invitations

The total number of failed invitation attempts since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · invitations

The total number of failed re-invitation attempts since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · calls

The current number of calls into and originating from the MPA.

Gauge32 · calls

The current number of Incoming calls.

Gauge32 · calls

The current number of calls originating from the MPA.

Gauge32 · sessions

The number of currently registered Client Sessions.

Counter64 (0..18446744073709551615) · sessions

The total number of client sessions opened(Including disconnected clients), since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of instant messages sent since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of instant messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · updates

The total number of presence documents received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · bytes

Total number of bytes received in presence updates, since application start time specified by cmmcaStartTime.

Gauge32 · addresses

The real time number of SIP current registrations to SIP Registrar.

Gauge32 · addresses

The real time number of SIP addresses currently registered.

Gauge32 · addresses

The real time number of IM addresses currently registered.

Gauge32 · addresses

The real time number active presence addresses currently being monitored.

Counter64 (0..18446744073709551615) · addresses

The total number of SIP Registrations to SIP Registrar (Including deregistered ones) since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · addresses

The total number of SIP addresses registered(Including deregistered ones) since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · addresses

The total number of IM addresses registered(Including deregistered ones) since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · addresses

The total number of Presentities registered with presence server(Including deregistered ones) since application start time specified by cmmcaStartTime.

Gauge32 · interactions

The real time number of Interactions that currently exist.

Gauge32 · addresses

The real time number of Publishers currently registered with presence server.

Gauge32 · addresses

The real time number of Publishers registered with presence server(Including deregistered ones).

Counter64 (0..18446744073709551615) · messages

The total number of messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of contact detail messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of contact detail messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of contact detail attributes messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of contact segment detail messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of contact segment detail messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of contact segment media detail messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of resource task detail messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of resource task detail messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of task state change messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of resource state change messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of resource state change messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of version response messages received since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of version request messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of node synchronization messages dispatched since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · records

Total number of Contact Detail Records written to the database since since application start time specified by cmmcaStartTime. For each ContactDetail Record written this metric will be incremented by one.

Counter64 (0..18446744073709551615) · records

Total number of ContactDetailAttribute Records written to the database since application start time specified by cmmcaStartTime. For each ContactDetailAttribute record written this metric will be incremented by one.

Counter64 (0..18446744073709551615) · records

Total number of Contact Segment Detail Records written to the database since application start time specified by cmmcaStartTime. For each ContactSegmentDetail Record written this metric will be incremented by one.

Counter64 (0..18446744073709551615) · records

Total number of ResourceTaskDetail Records written to the database since application start time specified by cmmcaStartTime. For each ResourceTaskDetail Record written this metric will be incremented by one.

Counter64 (0..18446744073709551615) · records

Total number of ResourceEventDetail Records written to the database since application start time specified by cmmcaStartTime. For each ResourceEventDetail Record written this metric will be incremented by one.

Counter64 (0..18446744073709551615) · records

Total number of AssignmentQueueDetail Records written to the database since application start time specified by cmmcaStartTime. For each AssignmentQueueDetail Record written this metric will be incremented by one.

Counter64 (0..18446744073709551615) · records

Total number of AssignmentQueueAttribute Records written to the database since application start time specified by cmmcaStartTime. For each AssignmentQueueAttribute written received, this metric will be incremented by one.

Counter64 (0..18446744073709551615) · records

Total number of Contact Segment Media Detail Records written to the database since application start time specified by cmmcaStartTime. For each ContactSegment media Detail Record written this metric will be incremented by one.

Counter64 (0..18446744073709551615) · writes

Total number of writes to the database by the Reporting Server since application start time specified by cmmcaStartTime. For each write to the database by the Reporting Server, this metric will be increased by one.

Gauge32 · records

Total number of ContactDetailRecords written to the database by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · records

Total number of ContactDetailAttribute Records written to the database by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · records

Total number of ContactSegmentDetail Records written to the database by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · records

Total number of ResourceTaskDetail Records written to the database by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · records

Total number of ResourceEventDetail Records written to the database by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · records

Total number of AssignmentQueueDetail Records written to the database by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · records

Total number of AddignmentQueueAttribute Records written to the database by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · records

Total number of Contact Segment Media Detail Records written to the database by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

Gauge32 · writes

IntervalDBWrites is an interval metric indicating the total number of writes to the database made by the Reporting Server during the last interval specified by the corresponding cmmcaServiceIntPeriod in cmmcaServiceTable.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

A descriptive text used to indicate the current status associated with the Reporting database Server.

Gauge32 · sessions

Current number of active Reporting database User sessions.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes

The real time allocated size (bytes) of the Reporting Server database.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes

The real time number of bytes of used database space.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes

The real time number of bytes of free database space.

Gauge32 · percentage

The real time percentage of used database space.

Gauge32 · percentage

The real time percentage of free database space.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes

The real time size of the transaction log in Reporting Server database.

Counter64 (0..18446744073709551615) · sockets

The total number of socket connections since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · sockets

The total number of socket disconnections since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · bytes

The total number of bytes sent to the PIM since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · bytes

The total number of bytes received from the PIM since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of messages sent to the PIM since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · messages

The total number of messages received from the PIM since application start time specified by cmmcaStartTime.

Gauge32 · messages

The current ACMI output queue depth.

Gauge32 · milliseconds

The real time Queuing time of the message in the ACMI output queue in milliseconds.

Gauge32 · agents

The real time number of agents being monitored.

Gauge32 · queues

The real time number of Assignment Queues being monitored.

Gauge32 · routes

The real time number of DNIS being monitored.

Gauge32 · dialogues

The real time number of pending QueryAgentState dialogues.

Gauge32 · dialogues

The real time number of pending GetContactDetail dialogues.

Counter64 (0..18446744073709551615) · timeouts

The total number of QueryAgentState timeouts since application start time specified by cmmcaStartTime.

Counter64 (0..18446744073709551615) · timeouts

The total Number of GetContactDetail timeouts since application start time specified by cmmcaStartTime.

Gauge32 · milliseconds

The real time QueryAgentState response delay.

Gauge32 · milliseconds

The real time GetContactDetail response delay.

Gauge32 · messages

The real time number of pending CallTerminationEvent messages.