2026-02-10
This MIB module defines the managed objects and statistics objects for physical layer characteristics of optical line systems and optical transport devices. Performance monitoring (PM) parameters are used to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: OTS : Optical Transmission Section OTS-OCH : Optical Channel Information on OTS ATTN : Optical Attenuation GAIN : Optical Amplifier Gain TILT : Optical Amplifier TILT LBC : Laser Bias Current OSRI : Optical Safety Remote Interlock TX : Transmit RX : Receive VOA : Variable Optical Attenuator dB : Decibel dBm : Decibel-milliwatt mW : Milliwatt nm : Nanometer.
Download CISCO-OPTICAL-OTS-MIB.txt Open CISCO-OPTICAL-OTS-MIB.txt in a new tab
SCALARS (10) · TABLES (8) · TRAPS (3)
| Name | OID |
|---|---|
| cooOtsStatusChange | 1.3.6.1.4.1.9.9.834.0.1 |
| cooOtsOchStatusChange | 1.3.6.1.4.1.9.9.834.0.2 |
| cooOtsEquipmentAlarm | 1.3.6.1.4.1.9.9.834.0.3 |
END OF TOC
1.3.6.1.4.1.9.9.834.1.1.1
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object controls the generation of cooOtsStatusChange notification. If the value of this object is 'true', then the generation of cooOtsStatusChange notification is enabled. If the value of this object is 'false', then the generation of cooOtsStatusChange notification is disabled.
1.3.6.1.4.1.9.9.834.1.1.4
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object controls the generation of cooOtsOchStatusChange notification. If the value of this object is 'true', then the generation of cooOtsOchStatusChange notification is enabled. If the value of this object is 'false', then the generation of cooOtsOchStatusChange notification is disabled.
1.3.6.1.4.1.9.9.834.1.5.1
SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t
This object indicates the location of the component that raised alarm, within the device.
1.3.6.1.4.1.9.9.834.1.5.2
CoiOptAlarmType1 = alarmUnknown2 = equipmentFailureThis value indicates the alarm type. alarmUnknown(1) - denotes unknown alarm type. equipmentFailure(2) - denotes equipment fail alarm type. · Integer32
This object indicates the type of alarm that is raised.
1.3.6.1.4.1.9.9.834.1.5.3
TimeStampThe value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset to zero as a result of a re- initialization of the network management (sub)system, then the values of all TimeStamp objects are also reset. However, after approximately 497 days without a re- initialization, the sysUpTime object will reach 2^^32-1 and then increment around to zero; in this case, existing values of TimeStamp objects do not change. This can lead to ambiguities in the value of TimeStamp objects. · TimeTicks
This object represents the time when an event occurred. This is accurate only upto a second.
1.3.6.1.4.1.9.9.834.1.5.4
SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t
This object represents the user-visible name, which uniquely identifies the alarm in the system.
1.3.6.1.4.1.9.9.834.1.5.5
SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t
This object provides additional information about the alarm. This object would be an empty string if no additional information is specified.
1.3.6.1.4.1.9.9.834.1.5.6
CoiOptAlarmSeverity1 = notReported2 = notAlarmed3 = minor4 = major5 = criticalThis will indicate the severity of the notification being sent out. Valid values are - notReported(1) - alarm not reported. notAlarmed(2) - alarm not raised. minor(3) - minor alarm. major(4) - major alarm. critical(5) - critical alarm. · Integer32
This object specifies alarm severity.
1.3.6.1.4.1.9.9.834.1.5.7
CoiOptAlarmStatus1 = raised2 = cleared3 = transientThis will indicate the status of the alarm. Valid values are - raised(1) - alarm in raised state. cleared(2) - alarm in cleared state. transient(3)- alarm in transient state. · Integer32
This object specifies alarm status.
1.3.6.1.4.1.9.9.834.1.5.8
CoiOptAlarmServiceAffecting1 = serviceAffecting2 = nonServiceAffectingThis will indicate the sevice-affecting state of the alarm. Valid values are - Service affecting(1) - alarm affects service. Non-Service affecting(2)- alarm does not affect service. · Integer32
This object specifies the service affecting state of the alarm.
1.3.6.1.4.1.9.9.834.1.1.2
Index: ifIndex
This table provides management information for OTS optical layer related attributes of interfaces with an ifType of opticalTransport(196).
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.834.1.1.2.1.1
CiscoOpticalOtsPortType1 = line2 = com3 = osc4 = comCheck5 = working6 = protected7 = addDropThis value indicates the port type for optical OTS interface. Valid values are - line(1) : port facing the fiber and far-end section. com(2) : port facing the near-end section. osc(3) : port for optical service channel signal. comCheck(4) : com monitoring port for near-end safety usage. working(5) : physical working port if device protection. protected(6) : physical protected port if device protection. · Integer32
This object represents the port type of the optical OTS interface.
1.3.6.1.4.1.9.9.834.1.1.2.1.2
CiscoOpticalOtsLaserStatus1 = unknown2 = on3 = off4 = aprThis value indicates the module laser status. Valid values are - unknown(1) : unknown status on(2) : laser on off(3) : laser off apr(4) : Denotes Automatic Power Reduction (APR) · Integer32
This object represents the current operational state of the laser.
1.3.6.1.4.1.9.9.834.1.1.2.1.3
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the receive power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.4
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the transmit power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.5
CiscoOpticalOtsGainInDbOTS ports associated to amplifier device,this value represent the amplifier gain setting. An integer value that represents the gain level in 1/100ths of dB. A negative value represents not meaninful value in case the amplifier is switched off for any reason. Example: The value 800 represents an gain level of 8.0 dB. (-100..4000) · Integer32 · 1/100 dB
This object represents the amplifier gain value in 1/100 dB on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.6
CiscoOpticalOtsTiltInDbOTS ports associated to amplifier device, this values represent the tilt parameter. An integer value that represents the tilt level in 1/100ths of dB. Example: The value 300 represents a tilt level of 3.0 dB. (-500..500) · Integer32 · 1/100 dB
This object represents the amplifier tilt value in 1/100 dB on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.7
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to represents the total receive power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.8
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to represents the total transmit power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.9
CiscoOpticalOtsVoaAttenInDbAn unsigned integer value that represents the VOA attenuation level in 1/100ths of dB. Example: The value 200 represents an attenuation level of 2.0 dB. · Unsigned32 · 1/100 dB
This object represents the receive VOA attenuation value in 1/100 dB on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.10
CiscoOpticalOtsVoaAttenInDbAn unsigned integer value that represents the VOA attenuation level in 1/100ths of dB. Example: The value 200 represents an attenuation level of 2.0 dB. · Unsigned32 · 1/100 dB
This object represents the transmit VOA attenuation value in 1/100 dB on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.11
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the receive low threshold in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.12
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the transmit low threshold in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.13
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the amplifier channel power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.14
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the maximum delta on channel power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.15
CiscoOpticalOtsAmpliControlMode1 = manual2 = auto3 = powerOTS ports associated to amplifier device, this value indicates how the amplifier is controlled. Valid values are - manual(1) : manual control mode (An external entity has to provide gain/tilt settings) auto(2) : automatic control mode (An internal will provide gain/tilt calculation based on power setpoint) power(3) : power control mode (An internal will provide gain/tilt calculation based on power mode settings · Integer32
This object is used to configure the amplifier control mode.
1.3.6.1.4.1.9.9.834.1.1.2.1.16
CiscoOpticalOtsAmpliGainRange1 = normal2 = extendedOTS ports associated to amplifier device, this value indicates the working ranges available for amplifier gain. Valid values are - normal(1) : normal gain range extended(2) : extended gain range · Integer32
This object is used to configure the amplifier gain range.
1.3.6.1.4.1.9.9.834.1.1.2.1.17
CiscoOpticalOtsAmpliSafetyCtrlMode1 = auto2 = disabledOTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode · Integer32
This object is used to configure the safety control mode.
1.3.6.1.4.1.9.9.834.1.1.2.1.18
CiscoOpticalOtsOsri1 = on2 = offOTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation · Integer32
This object is used to configure the OSRI.
1.3.6.1.4.1.9.9.834.1.1.2.1.19
CiscoOpticalOtsProtectionPortRole1 = active2 = standbyThis value indicates the actual OTS port role in case a protection device is in place. Valid values are - active(1) : active port standby(2) : standby port · Integer32
This object represents the port role on optical channel interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.20
CiscoOpticalOtsState1 = up2 = down3 = adminDownThis value indicates the controller status. Valid values are - up(1) : controller operstatus up down(2) : controller operstatus down adminDown(3) : controller administratively down · Integer32
This object represents the controller status of optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.21
CiscoOpticalOtsTranspAdminState1 = inService2 = outOfService3 = maintenance4 = ainsThis value indicates the transport administrative status. Valid values are - inService(1) : transport administrative status in-service outOfService(2) : transport administrative status out-of-service maintenance(3) : transport administrative status maintenance ains(4) : transport administrative status automatic in-service · Integer32
This object represents the transport administration status on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.22
BITS
This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the fail-high threshold highTXPwr : Output optical power reading over the fail-high threshold lowRXPwr : Input optical power reading below the fail-low threshold lowTXPwr : Output optical power reading below the fail-low threshold lospRXPwr : Loss of optical power signal locRXPwr : Loss of optical continuity degLowGain : Amplifier gain degrade low degHighGain : Amplifier gain degrade high alsAmp : Amplifier automatic laser shutdown for safety reason aprAmp : Amplifier automatic power reduction noEqAutoAmp : Channels power not equalized for amplifier automatic control mode misAutoAmp : Misconfiguration for amplifier automatic control mode switchToProtect : Protected port switching to active role autoAmpliCtrlRunning : Amplifier automatic control mode algorithm running
1.3.6.1.4.1.9.9.834.1.1.2.1.23
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dB
This object is used to represents the span loss power in 1/100 dB on optical OTS interfaces
1.3.6.1.4.1.9.9.834.1.1.2.1.24
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dB
This object is used to represents the span loss power in 1/100 dB on optical OTS interfaces
1.3.6.1.4.1.9.9.834.1.1.2.1.25
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object represents the RX direction status of optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.26
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object represents the TX direction status of optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.27
CiscoOpticalOtsIEGainInDbOTS ports associated to amplifier device,this value represent the amplifier gain setting for Ingress and Egress Amplifiers. An integer value that represents the gain level in 1/10ths of dB. A negative value indicates that the amplifier is switched off for any reason. Example: The value 80 represents an gain level of 8.0 dB. (80..400) · Integer32 · 1/10 dB
This object represents the amplifier gain value in 1/10 dB on optical OTS interfaces for ingress direction.
1.3.6.1.4.1.9.9.834.1.1.2.1.28
CiscoOpticalOtsIETiltInDbThis value represents the tilt parameter for an OTS port associated to the amplifier device. An integer value that represents the tilt level in 1/10ths of dB. Example: The value 30 represents a tilt level of 3.0 dB. (-50..50) · Integer32 · 1/10 dB
This object represents the amplifier tilt value in 1/10 dB on optical OTS interfaces for ingress direction.
1.3.6.1.4.1.9.9.834.1.1.2.1.29
CiscoOpticalOtsAmpliGainRange1 = normal2 = extendedOTS ports associated to amplifier device, this value indicates the working ranges available for amplifier gain. Valid values are - normal(1) : normal gain range extended(2) : extended gain range · Integer32
This object is used to configure Ingress amplifier gain range.
1.3.6.1.4.1.9.9.834.1.1.2.1.30
CiscoOpticalOtsAmpliSafetyCtrlMode1 = auto2 = disabledOTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode · Integer32
This object is used to configure Ingress safety control mode.
1.3.6.1.4.1.9.9.834.1.1.2.1.31
CiscoOpticalOtsOsri1 = on2 = offOTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation · Integer32
This object is used to configure Ingress OSRI.
1.3.6.1.4.1.9.9.834.1.1.2.1.32
CiscoOpticalOtsIEGainInDbOTS ports associated to amplifier device,this value represent the amplifier gain setting for Ingress and Egress Amplifiers. An integer value that represents the gain level in 1/10ths of dB. A negative value indicates that the amplifier is switched off for any reason. Example: The value 80 represents an gain level of 8.0 dB. (80..400) · Integer32 · 1/10 dB
This object represents the amplifier gain value in 1/10 dB on optical OTS interfaces for Egress direction.
1.3.6.1.4.1.9.9.834.1.1.2.1.33
CiscoOpticalOtsIETiltInDbThis value represents the tilt parameter for an OTS port associated to the amplifier device. An integer value that represents the tilt level in 1/10ths of dB. Example: The value 30 represents a tilt level of 3.0 dB. (-50..50) · Integer32 · 1/10 dB
This object represents the amplifier tilt value in 1/10 dB on optical OTS interfaces for egress direction.
1.3.6.1.4.1.9.9.834.1.1.2.1.34
CiscoOpticalOtsAmpliGainRange1 = normal2 = extendedOTS ports associated to amplifier device, this value indicates the working ranges available for amplifier gain. Valid values are - normal(1) : normal gain range extended(2) : extended gain range · Integer32
This object is used to configure the Egress amplifier gain range.
1.3.6.1.4.1.9.9.834.1.1.2.1.35
CiscoOpticalOtsAmpliSafetyCtrlMode1 = auto2 = disabledOTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode · Integer32
This object is used to configure Egress safety control mode.
1.3.6.1.4.1.9.9.834.1.1.2.1.36
CiscoOpticalOtsOsri1 = on2 = offOTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation · Integer32
This object is used to configure Egress OSRI.
1.3.6.1.4.1.9.9.834.1.1.2.1.37
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the transmit power(C+L) in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.38
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the receive power(C+L) in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.39
INTEGER0 = off1 = on · Integer32
This object represents Force Automatic Power Reduction for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.40
INTEGER0 = off1 = on · Integer32
This object represents Force Automatic Power Reduction for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.41
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the BR power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.42
INTEGER0 = off1 = greenOn2 = greenFlashing3 = yellowOn4 = yellowFlashing5 = redOn6 = redFlashing7 = na · Integer32
This object represents LED state for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.43
CiscoOpticalOtsBrRatioInDbAn integer value that represents BR Ratio in dB. Example: The value -4500 represents a BR Ratio of -45.00 dB. (-5000..0) · Integer32
This object represents EgressAmpliBrRatio for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.44
CiscoOpticalOtsAmpliControlMode1 = manual2 = auto3 = powerOTS ports associated to amplifier device, this value indicates how the amplifier is controlled. Valid values are - manual(1) : manual control mode (An external entity has to provide gain/tilt settings) auto(2) : automatic control mode (An internal will provide gain/tilt calculation based on power setpoint) power(3) : power control mode (An internal will provide gain/tilt calculation based on power mode settings · Integer32
This object represents the Configured Amplifier Control Mode Value for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.45
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the Configured Egress Amplifier Power Value in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.46
CiscoOpticalOtsTemperatureAn integer value that represents Temperature in Celsius for OTS controllers. Example: The value 4500 represents a Temperature 45.00 C. (-5000..10000) · Integer32 · 1/100 C
This object represents the Controller Temperature in 1/100 C on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.47
CiscoOpticalOtsVoltageAn integer value that represents Voltage for OTS controller. Example: The value 350 represents a Voltage 3.50 V. (-5000..10000) · Integer32 · 1/100 V
This object represents the Controller Temperature in 1/100 V on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.2.1.48
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents EgressAmpliBrPower for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.3
Index: ifIndex
This table provides management information for OTS-OCH optical layer related attributes of interfaces with an ifType of opticalTransport(196).
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.834.1.1.3.1.1
CiscoOpticalOtsPortType1 = line2 = com3 = osc4 = comCheck5 = working6 = protected7 = addDropThis value indicates the port type for optical OTS interface. Valid values are - line(1) : port facing the fiber and far-end section. com(2) : port facing the near-end section. osc(3) : port for optical service channel signal. comCheck(4) : com monitoring port for near-end safety usage. working(5) : physical working port if device protection. protected(6) : physical protected port if device protection. · Integer32
This object represents the port type of the optical OTS-OCH interface.
1.3.6.1.4.1.9.9.834.1.1.3.1.2
CiscoOpticalOtsLaserStatus1 = unknown2 = on3 = off4 = aprThis value indicates the module laser status. Valid values are - unknown(1) : unknown status on(2) : laser on off(3) : laser off apr(4) : Denotes Automatic Power Reduction (APR) · Integer32
This object represents the current operational state of the laser.
1.3.6.1.4.1.9.9.834.1.1.3.1.3
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the receive power in 1/100 dBm on optical OTS-OCH interfaces.
1.3.6.1.4.1.9.9.834.1.1.3.1.4
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the transmit power in 1/100 dBm on optical OTS-OCH interfaces.
1.3.6.1.4.1.9.9.834.1.1.3.1.5
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the receive low threshold in 1/100 dBm on optical OTS-OCH interfaces.
1.3.6.1.4.1.9.9.834.1.1.3.1.6
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the transmit low threshold in 1/100 dBm on optical OTS-OCH interfaces.
1.3.6.1.4.1.9.9.834.1.1.3.1.7
CoiOpticalWavelengthThis value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1Reference: ITU - T Recommendation G.694.1 - Spectral grids for WDM applications: DWDM frequency grid, May 2002 (0 | 1528770..1604030) · Unsigned32 · 1/100 nm
This object represents the wavelength on optical OTS-OCH interfaces (unit 1/100 nm).
1.3.6.1.4.1.9.9.834.1.1.3.1.8
Unsigned32 (1913500..1961000) · 100 MHz
This object represents the frequency on optical Ots-Och channel interfaces (unit 100 MHz).
1.3.6.1.4.1.9.9.834.1.1.3.1.9
Unsigned32 (1..384)
This object represents the channel number on optical OTS-OCH interfaces.
1.3.6.1.4.1.9.9.834.1.1.3.1.10
CiscoOpticalOtsState1 = up2 = down3 = adminDownThis value indicates the controller status. Valid values are - up(1) : controller operstatus up down(2) : controller operstatus down adminDown(3) : controller administratively down · Integer32
This object represents the controller status of optical OTS-OCH interfaces.
1.3.6.1.4.1.9.9.834.1.1.3.1.11
CiscoOpticalOtsTranspAdminState1 = inService2 = outOfService3 = maintenance4 = ainsThis value indicates the transport administrative status. Valid values are - inService(1) : transport administrative status in-service outOfService(2) : transport administrative status out-of-service maintenance(3) : transport administrative status maintenance ains(4) : transport administrative status automatic in-service · Integer32
This object represents the transport administration status on optical OTS-OCH interfaces.
1.3.6.1.4.1.9.9.834.1.1.3.1.12
BITS
This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the fail-high threshold highTXPwr : Output optical power reading over the fail-high threshold lowRXPwr : Input optical power reading below the fail-low threshold lowTXPwr : Output optical power reading below the fail-low threshold lospRXPwr : Loss of optical power signal locRXPwr : Loss of optical continuity degLowGain : Amplifier gain degrade low degHighGain : Amplifier gain degrade high alsAmp : Amplifier automatic laser shutdown for safety reason aprAmp : Amplifier automatic power reduction noEqAutoAmp : Channels power not equalized for amplifier automatic control mode misAutoAmp : Misconfiguration for amplifier automatic control mode switchToProtect : Protected port switching to active role
1.3.6.1.4.1.9.9.834.1.1.3.1.13
Unsigned32 (500..8000) · 1/10 GHz
This object represents the frequency on optical Ots-Och channel interfaces (unit 1/10 GHz).
1.3.6.1.4.1.9.9.834.1.1.5
Index: ifIndex
This table provides raman information for optical layer related attributes of interfaces with an ifType of opticalTransport(196).
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.834.1.1.5.1.1
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 mW
This object represents the Power of Raman Pump Instance 1 for OTS interfaces (unit 1/100 mW).
1.3.6.1.4.1.9.9.834.1.1.5.1.2
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 mW
This object represents the Power of Raman Pump Instance 2 for OTS interfaces (unit 1/100 mW).
1.3.6.1.4.1.9.9.834.1.1.5.1.3
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 mW
This object represents the Power of Raman Pump Instance 3 for OTS interfaces (unit 1/100 mW).
1.3.6.1.4.1.9.9.834.1.1.5.1.4
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 mW
This object represents the Power of Raman Pump Instance 4 for OTS interfaces (unit 1/100 mW).
1.3.6.1.4.1.9.9.834.1.1.5.1.5
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 mW
This object represents the Power of Raman Pump Instance 5 for OTS interfaces (unit 1/100 mW).
1.3.6.1.4.1.9.9.834.1.1.5.1.6
CoiOpticalWavelengthThis value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1Reference: ITU - T Recommendation G.694.1 - Spectral grids for WDM applications: DWDM frequency grid, May 2002 (0 | 1528770..1604030) · Unsigned32 · 1/100 nm
This object represents the wavelength of Raman Pump Instance 1 for OTS interfaces (unit 1/100 nm).
1.3.6.1.4.1.9.9.834.1.1.5.1.7
CoiOpticalWavelengthThis value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1Reference: ITU - T Recommendation G.694.1 - Spectral grids for WDM applications: DWDM frequency grid, May 2002 (0 | 1528770..1604030) · Unsigned32 · 1/100 nm
This object represents the wavelength of Raman Pump Instance 2 for OTS interfaces (unit 1/100 nm).
1.3.6.1.4.1.9.9.834.1.1.5.1.8
CoiOpticalWavelengthThis value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1Reference: ITU - T Recommendation G.694.1 - Spectral grids for WDM applications: DWDM frequency grid, May 2002 (0 | 1528770..1604030) · Unsigned32 · 1/100 nm
This object represents the wavelength of Raman Pump Instance 3 for OTS interfaces (unit 1/100 nm).
1.3.6.1.4.1.9.9.834.1.1.5.1.9
CoiOpticalWavelengthThis value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1Reference: ITU - T Recommendation G.694.1 - Spectral grids for WDM applications: DWDM frequency grid, May 2002 (0 | 1528770..1604030) · Unsigned32 · 1/100 nm
This object represents the wavelength of Raman Pump Instance 4 for OTS interfaces (unit 1/100 nm).
1.3.6.1.4.1.9.9.834.1.1.5.1.10
CoiOpticalWavelengthThis value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1Reference: ITU - T Recommendation G.694.1 - Spectral grids for WDM applications: DWDM frequency grid, May 2002 (0 | 1528770..1604030) · Unsigned32 · 1/100 nm
This object represnts the wavelength of Raman Pump Instance 5 for OTS interfaces (unit 1/100 nm).
1.3.6.1.4.1.9.9.834.1.1.5.1.11
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 mW
This object represents the Composite Power of Raman Pump for OTS interfaces (unit 1/100 mW).
1.3.6.1.4.1.9.9.834.1.1.5.1.12
CiscoOpticalOtsOsri1 = on2 = offOTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation · Integer32
This object represents the Raman Osri for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.5.1.13
CiscoOpticalOtsAmpliSafetyCtrlMode1 = auto2 = disabledOTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode · Integer32
This object represent the Raman Safety Control Mode for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.5.1.14
INTEGER0 = off1 = on · Integer32
This object represents the Raman Force APR for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.5.1.15
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the Raman Br Power for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.5.1.16
CiscoOpticalOtsBrRatioInDbAn integer value that represents BR Ratio in dB. Example: The value -4500 represents a BR Ratio of -45.00 dB. (-5000..0) · Integer32 · 1/100 dB
This object represents the Raman BR Ratio for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.6
Index: ifIndex
This table provides ots transceiver detail for optical layer related attributes of interfaces with an ifType of opticalTransport(196).
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.834.1.1.6.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
This object represents the Controller Vendor Information on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7
Index: ifIndex · cooOtsController2PortType
This table provides management information for OTS optical layer related attributes of interfaces with an ifType of opticalTransport(196). DESIGN RATIONALE: This table supersedes the earlier cooOtsControllerTable which used only ifIndex as the INDEX. The previous design could not distinguish between LINE and COM port attributes on the same physical interface (e.g., different TX power, gain settings per port). The composite INDEX structure { ifIndex, cooOtsController2PortType } was introduced to support multi-port OLS modules where LINE and COM ports share an ifIndex but require independent operational data.
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.834.1.1.7.1.1
CiscoOpticalOtsPortType1 = line2 = com3 = osc4 = comCheck5 = working6 = protected7 = addDropThis value indicates the port type for optical OTS interface. Valid values are - line(1) : port facing the fiber and far-end section. com(2) : port facing the near-end section. osc(3) : port for optical service channel signal. comCheck(4) : com monitoring port for near-end safety usage. working(5) : physical working port if device protection. protected(6) : physical protected port if device protection. · Integer32
This object represents the port type of the optical OTS interface.
1.3.6.1.4.1.9.9.834.1.1.7.1.2
CiscoOpticalOtsLaserStatus1 = unknown2 = on3 = off4 = aprThis value indicates the module laser status. Valid values are - unknown(1) : unknown status on(2) : laser on off(3) : laser off apr(4) : Denotes Automatic Power Reduction (APR) · Integer32
This object represents the current operational state of the laser.
1.3.6.1.4.1.9.9.834.1.1.7.1.3
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the receive power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.4
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the transmit power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.5
CiscoOpticalOtsGainInDbOTS ports associated to amplifier device,this value represent the amplifier gain setting. An integer value that represents the gain level in 1/100ths of dB. A negative value represents not meaninful value in case the amplifier is switched off for any reason. Example: The value 800 represents an gain level of 8.0 dB. (-100..4000) · Integer32 · 1/100 dB
This object represents the amplifier gain value in 1/100 dB on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.6
CiscoOpticalOtsTiltInDbOTS ports associated to amplifier device, this values represent the tilt parameter. An integer value that represents the tilt level in 1/100ths of dB. Example: The value 300 represents a tilt level of 3.0 dB. (-500..500) · Integer32 · 1/100 dB
This object represents the amplifier tilt value in 1/100 dB on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.7
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to represents the total receive power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.8
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to represents the total transmit power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.9
CiscoOpticalOtsVoaAttenInDbAn unsigned integer value that represents the VOA attenuation level in 1/100ths of dB. Example: The value 200 represents an attenuation level of 2.0 dB. · Unsigned32 · 1/100 dB
This object represents the receive VOA attenuation value in 1/100 dB on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.10
CiscoOpticalOtsVoaAttenInDbAn unsigned integer value that represents the VOA attenuation level in 1/100ths of dB. Example: The value 200 represents an attenuation level of 2.0 dB. · Unsigned32 · 1/100 dB
This object represents the transmit VOA attenuation value in 1/100 dB on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.11
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the receive low threshold in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.12
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the transmit low threshold in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.13
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the amplifier channel power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.14
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the maximum delta on channel power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.15
CiscoOpticalOtsAmpliControlMode1 = manual2 = auto3 = powerOTS ports associated to amplifier device, this value indicates how the amplifier is controlled. Valid values are - manual(1) : manual control mode (An external entity has to provide gain/tilt settings) auto(2) : automatic control mode (An internal will provide gain/tilt calculation based on power setpoint) power(3) : power control mode (An internal will provide gain/tilt calculation based on power mode settings · Integer32
This object represents the amplifier control mode.
1.3.6.1.4.1.9.9.834.1.1.7.1.16
CiscoOpticalOtsAmpliGainRange1 = normal2 = extendedOTS ports associated to amplifier device, this value indicates the working ranges available for amplifier gain. Valid values are - normal(1) : normal gain range extended(2) : extended gain range · Integer32
This object is used to configure the amplifier gain range.
1.3.6.1.4.1.9.9.834.1.1.7.1.17
CiscoOpticalOtsAmpliSafetyCtrlMode1 = auto2 = disabledOTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode · Integer32
This object is used to configure the safety control mode.
1.3.6.1.4.1.9.9.834.1.1.7.1.18
CiscoOpticalOtsOsri1 = on2 = offOTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation · Integer32
This object is used to configure the OSRI.
1.3.6.1.4.1.9.9.834.1.1.7.1.19
CiscoOpticalOtsProtectionPortRole1 = active2 = standbyThis value indicates the actual OTS port role in case a protection device is in place. Valid values are - active(1) : active port standby(2) : standby port · Integer32
This object represents the port role on optical channel interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.20
CiscoOpticalOtsAdminState1 = up2 = downThis value indicates the controller status. Valid values are - up(1) : controller admin up down(2) : controller admin down · Integer32
This object represents the controller status of optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.21
CiscoOpticalOtsTranspAdminState1 = inService2 = outOfService3 = maintenance4 = ainsThis value indicates the transport administrative status. Valid values are - inService(1) : transport administrative status in-service outOfService(2) : transport administrative status out-of-service maintenance(3) : transport administrative status maintenance ains(4) : transport administrative status automatic in-service · Integer32
This object represents the transport administration status on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.22
BITS
This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the fail-high threshold highTXPwr : Output optical power reading over the fail-high threshold lowRXPwr : Input optical power reading below the fail-low threshold lowTXPwr : Output optical power reading below the fail-low threshold lospRXPwr : Loss of optical power signal locRXPwr : Loss of optical continuity degLowGain : Amplifier gain degrade low degHighGain : Amplifier gain degrade high alsAmp : Amplifier automatic laser shutdown for safety reason aprAmp : Amplifier automatic power reduction noEqAutoAmp : Channels power not equalized for amplifier automatic control mode misAutoAmp : Misconfiguration for amplifier automatic control mode switchToProtect : Protected port switching to active role autoAmpliCtrlRunning : Amplifier automatic control mode algorithm running
1.3.6.1.4.1.9.9.834.1.1.7.1.23
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dB
This object is used to represents the span loss power in 1/100 dB on optical OTS interfaces
1.3.6.1.4.1.9.9.834.1.1.7.1.24
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dB
This object is used to represents the span loss power in 1/100 dB on optical OTS interfaces
1.3.6.1.4.1.9.9.834.1.1.7.1.25
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object represents the RX direction status of optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.26
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object represents the TX direction status of optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.27
CiscoOpticalOts2IEGainInDbOTS ports associated with an amplifier device. This value represents the amplifier both Ingress and Egress gain setting. The gain is expressed in 1/10ths of a dB. A value of 0 indicates that the amplifier is switched off. Example: A value of 120 represents a gain level of 12.0 dB. (0 | 30..400) · Integer32 · 1/10 dB
This object represents the amplifier gain value in 1/10 dB on optical OTS interfaces for ingress direction.
1.3.6.1.4.1.9.9.834.1.1.7.1.28
CiscoOpticalOtsIETiltInDbThis value represents the tilt parameter for an OTS port associated to the amplifier device. An integer value that represents the tilt level in 1/10ths of dB. Example: The value 30 represents a tilt level of 3.0 dB. (-50..50) · Integer32 · 1/10 dB
This object represents the amplifier tilt value in 1/10 dB on optical OTS interfaces for ingress direction.
1.3.6.1.4.1.9.9.834.1.1.7.1.29
CiscoOpticalOtsAmpliGainRange1 = normal2 = extendedOTS ports associated to amplifier device, this value indicates the working ranges available for amplifier gain. Valid values are - normal(1) : normal gain range extended(2) : extended gain range · Integer32
This object represents the Ingress amplifier gain range.
1.3.6.1.4.1.9.9.834.1.1.7.1.30
CiscoOpticalOtsAmpliSafetyCtrlMode1 = auto2 = disabledOTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode · Integer32
This object represents the Ingress safety control mode.
1.3.6.1.4.1.9.9.834.1.1.7.1.31
CiscoOpticalOtsOsri1 = on2 = offOTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation · Integer32
This object represents the Ingress OSRI.
1.3.6.1.4.1.9.9.834.1.1.7.1.32
CiscoOpticalOts2IEGainInDbOTS ports associated with an amplifier device. This value represents the amplifier both Ingress and Egress gain setting. The gain is expressed in 1/10ths of a dB. A value of 0 indicates that the amplifier is switched off. Example: A value of 120 represents a gain level of 12.0 dB. (0 | 30..400) · Integer32 · 1/10 dB
This object represents the amplifier gain value in 1/10 dB on optical OTS interfaces for Egress direction.
1.3.6.1.4.1.9.9.834.1.1.7.1.33
CiscoOpticalOtsIETiltInDbThis value represents the tilt parameter for an OTS port associated to the amplifier device. An integer value that represents the tilt level in 1/10ths of dB. Example: The value 30 represents a tilt level of 3.0 dB. (-50..50) · Integer32 · 1/10 dB
This object represents the amplifier tilt value in 1/10 dB on optical OTS interfaces for egress direction.
1.3.6.1.4.1.9.9.834.1.1.7.1.34
CiscoOpticalOtsAmpliGainRange1 = normal2 = extendedOTS ports associated to amplifier device, this value indicates the working ranges available for amplifier gain. Valid values are - normal(1) : normal gain range extended(2) : extended gain range · Integer32
This object represents the Egress amplifier gain range.
1.3.6.1.4.1.9.9.834.1.1.7.1.35
CiscoOpticalOtsAmpliSafetyCtrlMode1 = auto2 = disabledOTS ports associated to amplifier device, this value indicates how the safety compliaces regulation are statisfied. Valid values are - auto(1) : automatic safety control mode disabled(2) : disabled safety control mode · Integer32
This object is used to configure Egress safety control mode.
1.3.6.1.4.1.9.9.834.1.1.7.1.36
CiscoOpticalOtsOsri1 = on2 = offOTS ports associated to amplifier device, this value indicates the optical safety remote interlock (OSRI) status. Valid values are - on(1) : force laser shutdown for safety interlock off(2) : normal operation · Integer32
This object is used to configure Egress OSRI.
1.3.6.1.4.1.9.9.834.1.1.7.1.37
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the transmit power(C+L) in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.38
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the receive power(C+L) in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.39
INTEGER0 = off1 = on · Integer32
This object represents Force Automatic Power Reduction for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.40
INTEGER0 = off1 = on · Integer32
This object represents Force Automatic Power Reduction for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.41
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the BR power in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.42
INTEGER0 = off1 = greenOn2 = greenFlashing3 = yellowOn4 = yellowFlashing5 = redOn6 = redFlashing7 = na · Integer32
This object represents LED state for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.43
CiscoOpticalOtsBrRatioInDbAn integer value that represents BR Ratio in dB. Example: The value -4500 represents a BR Ratio of -45.00 dB. (-5000..0) · Integer32
This object represents EgressAmpliBrRatio for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.44
CiscoOpticalOtsAmpliControlMode1 = manual2 = auto3 = powerOTS ports associated to amplifier device, this value indicates how the amplifier is controlled. Valid values are - manual(1) : manual control mode (An external entity has to provide gain/tilt settings) auto(2) : automatic control mode (An internal will provide gain/tilt calculation based on power setpoint) power(3) : power control mode (An internal will provide gain/tilt calculation based on power mode settings · Integer32
This object represents the Configured Amplifier Control Mode Value for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.45
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents the Configured Egress Amplifier Power Value in 1/100 dBm on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.46
CiscoOpticalOtsTemperatureAn integer value that represents Temperature in Celsius for OTS controllers. Example: The value 4500 represents a Temperature 45.00 C. (-5000..10000) · Integer32 · 1/100 C
This object represents the Controller Temperature in 1/100 C on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.47
CiscoOpticalOtsVoltageAn integer value that represents Voltage for OTS controller. Example: The value 350 represents a Voltage 3.50 V. (-5000..10000) · Integer32 · 1/100 V
This object represents the Controller Voltage in 1/100 V on optical OTS interfaces.
1.3.6.1.4.1.9.9.834.1.1.7.1.48
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object represents EgressAmpliBrPower for OTS interfaces.
1.3.6.1.4.1.9.9.834.1.2.1
Index: ifIndex · cooThreshIntervalType
This table provides threshold information for optical layer related attributes of interfaces with an ifType of opticalTransport(196) and interval type as cooThreshIntervalType.
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.834.1.2.1.1.1
CoiIntervalType1 = fifteenMin2 = oneDay3 = thirtySecondThis value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySecond(3)- values for the 30 Sec interval. · Integer32
This object represents the interval type during which the performance statistics are accumulated for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.2
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the threshold of minimum transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.1.1.3
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the threshold of minimum receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.1.1.4
Unsigned32 (0..100) · 1/10 percent
This object is used to configure the threshold of minimum laser bias current in 1/10 percent.
1.3.6.1.4.1.9.9.834.1.2.1.1.5
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the threshold of maximum Transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.1.1.6
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object is used to configure the threshold of maximum receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.1.1.7
Unsigned32 (0..100) · 1/10 percent
This object is used to configure the threshold of maximum Laser Bias Current in 1/10 percent for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.8
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of threshold minimum transmit power for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.9
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold minimum receive power for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.10
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold minimum laser bias current for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.11
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold maximum transmit power for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.12
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold maximum receive power for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.13
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold maximum laser bias current for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.14
Integer32 (0..500) · 1/100 dB
This object is used to configure the threshold of minimum ampli gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.1.1.15
Integer32 (0..500) · 1/100 dB
This object is used to configure the threshold of maximum ampli gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.1.1.16
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold maximum ampli gain for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.17
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold minimum ampli gain for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.18
Integer32 (-50..50) · 1/100 dB
This object is used to configure the threshold of minimum ampli gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.1.1.19
Integer32 (-50..50) · 1/100 db
This object is used to configure the threshold of maximum ampli gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.1.1.20
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold maximum ampli gain tilt for the interface.
1.3.6.1.4.1.9.9.834.1.2.1.1.21
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object is used to configure the enablement of the threshold minimum ampli gain tilt for the interface.
1.3.6.1.4.1.9.9.834.1.2.2
Index: ifIndex · cooCurrentIntervalType
This table provides current information for optical layer related attributes of interfaces with an ifType of opticalChannel(196), lane as cooCurrentLane and interval as cooCurrentIntervalType.
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.834.1.2.2.1.1
CoiIntervalType1 = fifteenMin2 = oneDay3 = thirtySecondThis value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySecond(3)- values for the 30 Sec interval. · Integer32
This object represents the interval type during which the current performance statistics are accumulated.
1.3.6.1.4.1.9.9.834.1.2.2.1.2
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current maximum transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.3
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current maximum receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.4
Unsigned32 (0..100) · 1/10 percent
This object specifies the current maximum laser bias current in 1/10 percent for the interface.
1.3.6.1.4.1.9.9.834.1.2.2.1.5
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current minimum transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.6
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current minimum receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.7
Unsigned32 (0..100) · 1/10 percent
This object specifies the current minimum laser bias current in 1/10 percent for the interface.
1.3.6.1.4.1.9.9.834.1.2.2.1.8
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current average transmit power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.9
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current average receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.10
Unsigned32 (0..100) · 1/10 percent
This object specifies the current average Laser Bias Current in 1/10 percent for the interface.
1.3.6.1.4.1.9.9.834.1.2.2.1.11
OCTET STRING
This object specifies the timestamp for the current bucket for the interface.
1.3.6.1.4.1.9.9.834.1.2.2.1.12
Integer32 · 1/100 dB
This object specifies the current minimum amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.13
Integer32 · 1/100 dB
This object specifies the current maximum amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.14
Integer32 · 1/100 dB
This object specifies the current average amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.15
Integer32 · 1/100 dB
This object specifies the current minimum amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.16
Integer32 · 1/100 dB
This object specifies the current maximum amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.17
Integer32 · 1/100 dB
This object specifies the current average amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.18
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current minimum transmit power C+L for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.19
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current maximum transmit power C+L for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.20
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current Average transmit power C+L for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.21
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current minimum receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.22
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current maximun receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.23
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the current average receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.2.1.24
Integer32 · 1/100 dB
This object specifies the current minimum ingress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.25
Integer32 · 1/100 dB
This object specifies the current maximum ingress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.26
Integer32 · 1/100 dB
This object specifies the current average ingress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.27
Integer32 · 1/100 dB
This object specifies the current minimum egress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.28
Integer32 · 1/100 dB
This object specifies the current maximum egress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.29
Integer32 · 1/100 dB
This object specifies the current average egress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.30
Integer32 · 1/100 dB
This object specifies the current minimum ingress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.31
Integer32 · 1/100 dB
This object specifies the current maximum ingress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.32
Integer32 · 1/100 dB
This object specifies the current average ingress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.33
Integer32 · 1/100 dB
This object specifies the current minimum egress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.34
Integer32 · 1/100 dB
This object specifies the current maximum egress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.2.1.35
Integer32 · 1/100 dB
This object specifies the current average egress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3
Index: ifIndex · cooIntervalType · cooIntervalNum
This table provides interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(196), lane as cooIntervalLane, Interval as cooIntervalIntervalType and history bucket as cooIntervalIntervalType.
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.834.1.2.3.1.1
CoiIntervalType1 = fifteenMin2 = oneDay3 = thirtySecondThis value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySecond(3)- values for the 30 Sec interval. · Integer32
This object represents the interval type during which the performance statistics are accumulated.
1.3.6.1.4.1.9.9.834.1.2.3.1.2
Unsigned32 (1..31)
This object identifies the interval for which the set of interval performance values is available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
1.3.6.1.4.1.9.9.834.1.2.3.1.3
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval maximum transmit power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.4
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval maximum receive power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.5
Unsigned32 (0..100) · 1/10 percent
This object specifies the interval maximum laser bias current in 1/10 percent for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.6
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval minimum transmit power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.7
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval minimum receive power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.8
Unsigned32 (0..100) · 1/10 percent
This object specifies the interval minimum laser bias current in 1/10 percent for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.9
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval average transmit power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.10
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval average receive power in 1/100 dBm for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.11
Unsigned32 (0..100) · 1/10 percent
This object specifies the interval average laser bias current in 1/10 percent for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.12
OCTET STRING
This object specifies the timestamp, for the bucket specified by 'cooIntervalNum', for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.13
Integer32 · 1/100 dB
This object specifies the interval minimum amplifier gain in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.14
Integer32 · 1/100 dB
This object specifies the interval maximum amplifier gain in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.15
Integer32
This object specifies the interval acerage amplifier gain in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.16
Integer32 · 1/100 dB
This object specifies the interval minimum amplifier gain tilt in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.17
Integer32 · 1/100 dB
This object specifies the interval maximum amplifier gain tilt in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.18
Integer32 · 1/100 dB
This object specifies the interval average amplifier gain tilt in 1/100 dB for the interface.
1.3.6.1.4.1.9.9.834.1.2.3.1.19
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval minimum transmit power C+L for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.3.1.20
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval maximum transmit power C+L for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.3.1.21
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval Average transmit power C+L for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.3.1.22
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval minimum receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.3.1.23
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval maximun receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.3.1.24
CoiOpticalPowerThis value indicates the optical receive or transmit power. (-4000..3000) · Integer32 · 1/100 dBm
This object specifies the interval average receive power for the interface in 1/100 dBm.
1.3.6.1.4.1.9.9.834.1.2.3.1.25
Integer32 · 1/100 dB
This object specifies the interval minimum ingress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.26
Integer32 · 1/100 dB
This object specifies the interval maximum ingress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.27
Integer32 · 1/100 dB
This object specifies the interval average ingress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.28
Integer32 · 1/100 dB
This object specifies the interval minimum egress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.29
Integer32 · 1/100 dB
This object specifies the interval maximum egress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.30
Integer32 · 1/100 dB
This object specifies the interval average egress amplifier gain for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.31
Integer32 · 1/100 dB
This object specifies the interval minimum ingress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.32
Integer32 · 1/100 dB
This object specifies the interval maximum ingress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.33
Integer32 · 1/100 dB
This object specifies the interval average ingress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.34
Integer32 · 1/100 dB
This object specifies the interval minimum egress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.35
Integer32 · 1/100 dB
This object specifies the interval maximum egress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.1.2.3.1.36
Integer32 · 1/100 dB
This object specifies the interval average egress amplifier gain tilt for the interface in 1/100 dB.
1.3.6.1.4.1.9.9.834.0.1
This notification is generated when the value of cooOtsControllerStatus changes. The varbind for this notification indicates the ifIndex, ifname of the OTS interface as well as controller port type and status.
1.3.6.1.2.1.2.2.1.1
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.2.1.31.1.1.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.
1.3.6.1.4.1.9.9.834.1.1.2.1.1
CiscoOpticalOtsPortType1 = line2 = com3 = osc4 = comCheck5 = working6 = protected7 = addDropThis value indicates the port type for optical OTS interface. Valid values are - line(1) : port facing the fiber and far-end section. com(2) : port facing the near-end section. osc(3) : port for optical service channel signal. comCheck(4) : com monitoring port for near-end safety usage. working(5) : physical working port if device protection. protected(6) : physical protected port if device protection. · Integer32
This object represents the port type of the optical OTS interface.
1.3.6.1.4.1.9.9.834.1.1.2.1.22
BITS
This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the fail-high threshold highTXPwr : Output optical power reading over the fail-high threshold lowRXPwr : Input optical power reading below the fail-low threshold lowTXPwr : Output optical power reading below the fail-low threshold lospRXPwr : Loss of optical power signal locRXPwr : Loss of optical continuity degLowGain : Amplifier gain degrade low degHighGain : Amplifier gain degrade high alsAmp : Amplifier automatic laser shutdown for safety reason aprAmp : Amplifier automatic power reduction noEqAutoAmp : Channels power not equalized for amplifier automatic control mode misAutoAmp : Misconfiguration for amplifier automatic control mode switchToProtect : Protected port switching to active role autoAmpliCtrlRunning : Amplifier automatic control mode algorithm running
1.3.6.1.4.1.9.9.834.0.2
This notification is generated when the value of cooOtsOchControllerStatus changes. The varbind for this notification indicates the ifIndex, ifname of the OTS-OCH interface as well as controller port type and status.
1.3.6.1.2.1.2.2.1.1
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.2.1.31.1.1.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.
1.3.6.1.4.1.9.9.834.1.1.3.1.1
CiscoOpticalOtsPortType1 = line2 = com3 = osc4 = comCheck5 = working6 = protected7 = addDropThis value indicates the port type for optical OTS interface. Valid values are - line(1) : port facing the fiber and far-end section. com(2) : port facing the near-end section. osc(3) : port for optical service channel signal. comCheck(4) : com monitoring port for near-end safety usage. working(5) : physical working port if device protection. protected(6) : physical protected port if device protection. · Integer32
This object represents the port type of the optical OTS-OCH interface.
1.3.6.1.4.1.9.9.834.1.1.3.1.12
BITS
This object indicates the current alarms status of the Optics layer. Alarms description : noDefect : No alarms highRXPwr : Input optical power reading over the fail-high threshold highTXPwr : Output optical power reading over the fail-high threshold lowRXPwr : Input optical power reading below the fail-low threshold lowTXPwr : Output optical power reading below the fail-low threshold lospRXPwr : Loss of optical power signal locRXPwr : Loss of optical continuity degLowGain : Amplifier gain degrade low degHighGain : Amplifier gain degrade high alsAmp : Amplifier automatic laser shutdown for safety reason aprAmp : Amplifier automatic power reduction noEqAutoAmp : Channels power not equalized for amplifier automatic control mode misAutoAmp : Misconfiguration for amplifier automatic control mode switchToProtect : Protected port switching to active role
1.3.6.1.4.1.9.9.834.0.3
This notification is generated whenever the optical equipment alarm is generated.
1.3.6.1.4.1.9.9.834.1.5.1
SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t
This object indicates the location of the component that raised alarm, within the device.
1.3.6.1.4.1.9.9.834.1.5.2
CoiOptAlarmType1 = alarmUnknown2 = equipmentFailureThis value indicates the alarm type. alarmUnknown(1) - denotes unknown alarm type. equipmentFailure(2) - denotes equipment fail alarm type. · Integer32
This object indicates the type of alarm that is raised.
1.3.6.1.4.1.9.9.834.1.5.3
TimeStampThe value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset to zero as a result of a re- initialization of the network management (sub)system, then the values of all TimeStamp objects are also reset. However, after approximately 497 days without a re- initialization, the sysUpTime object will reach 2^^32-1 and then increment around to zero; in this case, existing values of TimeStamp objects do not change. This can lead to ambiguities in the value of TimeStamp objects. · TimeTicks
This object represents the time when an event occurred. This is accurate only upto a second.
1.3.6.1.4.1.9.9.834.1.5.4
SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t
This object represents the user-visible name, which uniquely identifies the alarm in the system.
1.3.6.1.4.1.9.9.834.1.5.5
SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t
This object provides additional information about the alarm. This object would be an empty string if no additional information is specified.
1.3.6.1.4.1.9.9.834.1.5.6
CoiOptAlarmSeverity1 = notReported2 = notAlarmed3 = minor4 = major5 = criticalThis will indicate the severity of the notification being sent out. Valid values are - notReported(1) - alarm not reported. notAlarmed(2) - alarm not raised. minor(3) - minor alarm. major(4) - major alarm. critical(5) - critical alarm. · Integer32
This object specifies alarm severity.
1.3.6.1.4.1.9.9.834.1.5.7
CoiOptAlarmStatus1 = raised2 = cleared3 = transientThis will indicate the status of the alarm. Valid values are - raised(1) - alarm in raised state. cleared(2) - alarm in cleared state. transient(3)- alarm in transient state. · Integer32
This object specifies alarm status.
1.3.6.1.4.1.9.9.834.1.5.8
CoiOptAlarmServiceAffecting1 = serviceAffecting2 = nonServiceAffectingThis will indicate the sevice-affecting state of the alarm. Valid values are - Service affecting(1) - alarm affects service. Non-Service affecting(2)- alarm does not affect service. · Integer32
This object specifies the service affecting state of the alarm.
1.3.6.1.2.1.31.1.1.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.