This MIB module describes new/modified notification objects/events, which are defined in the latest version for OSPF MIB IETF draft draftietf-ospf-mib-update-05.txt. Support for OSPF Sham link is also added
An octet string serving as a bit map for
the trap events defined by the OSPF traps in this MIB. This object is used to enable and
disable specific OSPF traps where a 1
in the corresponding bit field represents
enabled.
Potential types of configuration conflicts.
Used by the cospfConfigError and cospfConfigVirtError
traps. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as noError.
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
cospfPacketSrc
1.3.6.1.4.1.9.10.101.1.1.4
IpAddress SIZE (4)
The IP address of an inbound packet that can- not be identified by a neighbor instance. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as 0.0.0.0.
Trap details
cospfIfConfigError
1.3.6.1.4.1.9.10.101.0.1
A cospfIfConfigError trap signifies that a
packet with mismatched parameter MTU has been
received on a non-virtual interface from a
router.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
ospfIfIpAddress
1.3.6.1.2.1.14.7.1.1
IpAddress SIZE (4)
The IP address of this OSPF interface.
ospfAddressLessIf
1.3.6.1.2.1.14.7.1.2
InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d
For the purpose of easing the instancing of addressed and addressless interfaces; this variable takes the value 0 on interfaces with IP addresses and the corresponding value of ifIndex for interfaces having no IP address.
cospfPacketSrc
1.3.6.1.4.1.9.10.101.1.1.4
IpAddress SIZE (4)
The IP address of an inbound packet that can- not be identified by a neighbor instance. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as 0.0.0.0.
Potential types of configuration conflicts.
Used by the cospfConfigError and cospfConfigVirtError
traps. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as noError.
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
cospfVirtIfConfigError
1.3.6.1.4.1.9.10.101.0.2
A cospfVirtIfConfigError trap signifies that a
packet with mismatched parameter MTU has been received
on a virtual interface from a router.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
ospfVirtIfAreaId
1.3.6.1.2.1.14.9.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The transit area that the virtual link traverses. By definition, this is not 0.0.0.0.
ospfVirtIfNeighbor
1.3.6.1.2.1.14.9.1.2
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
Potential types of configuration conflicts.
Used by the cospfConfigError and cospfConfigVirtError
traps. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as noError.
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
cospfTxRetransmit
1.3.6.1.4.1.9.10.101.0.3
A cospfTxRetransmit trap signifies than an
OSPF packet, which has been associated with
an Opaque LSA LSDB Entry, has been retransmitted
on a non-virtual interface.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
ospfIfIpAddress
1.3.6.1.2.1.14.7.1.1
IpAddress SIZE (4)
The IP address of this OSPF interface.
ospfAddressLessIf
1.3.6.1.2.1.14.7.1.2
InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d
For the purpose of easing the instancing of addressed and addressless interfaces; this variable takes the value 0 on interfaces with IP addresses and the corresponding value of ifIndex for interfaces having no IP address.
ospfNbrRtrId
1.3.6.1.2.1.14.10.1.3
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
The type of the link state advertisement. Each link state type has a separate advertisement format. Reference: OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header The OSPF Opaque LSA Option (RFC 2370)
ospfLsdbLsid
1.3.6.1.2.1.14.4.1.3
IpAddress SIZE (4)
The Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. Reference: OSPF Version 2, Section 12.1.4 Link State ID
ospfLsdbRouterId
1.3.6.1.2.1.14.4.1.4
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
The 32-bit number that uniquely identifies the originating router in the Autonomous System. Reference: OSPF Version 2, Appendix C.1 Global parameters
cospfVirtIfTxRetransmit
1.3.6.1.4.1.9.10.101.0.4
A cospfVirtTxRetransmit trap signifies than an
OSPF packet, which has been associated with
an Opaque LSA LSDB Entry, has been retransmitted
on a non-virtual interface.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
ospfVirtIfAreaId
1.3.6.1.2.1.14.9.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The transit area that the virtual link traverses. By definition, this is not 0.0.0.0.
ospfVirtIfNeighbor
1.3.6.1.2.1.14.9.1.2
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
The type of the link state advertisement. Each link state type has a separate advertisement format. Reference: OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header The OSPF Opaque LSA Option (RFC 2370)
ospfLsdbLsid
1.3.6.1.2.1.14.4.1.3
IpAddress SIZE (4)
The Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. Reference: OSPF Version 2, Section 12.1.4 Link State ID
ospfLsdbRouterId
1.3.6.1.2.1.14.4.1.4
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
The 32-bit number that uniquely identifies the originating router in the Autonomous System. Reference: OSPF Version 2, Appendix C.1 Global parameters
cospfOriginateLsa
1.3.6.1.4.1.9.10.101.0.5
A cospfOriginateLsa trap signifies that a new
Opaque LSA has been originated by this router.
This trap should not be invoked for simple refreshes
of LSAs (which happesn every 30 minutes), but
instead will only be invoked when an LSA is
(re)originated due to a topology change. Additionally,
this trap does not include LSAs that
are being flushed because they have reached
MaxAge.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
ospfLsdbAreaId
1.3.6.1.2.1.14.4.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The 32-bit identifier of the area from which the LSA was received. Reference: OSPF Version 2, Appendix C.2 Area parameters
The type of the link state advertisement. Each link state type has a separate advertisement format. Reference: OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header The OSPF Opaque LSA Option (RFC 2370)
ospfLsdbLsid
1.3.6.1.2.1.14.4.1.3
IpAddress SIZE (4)
The Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. Reference: OSPF Version 2, Section 12.1.4 Link State ID
ospfLsdbRouterId
1.3.6.1.2.1.14.4.1.4
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
The 32-bit number that uniquely identifies the originating router in the Autonomous System. Reference: OSPF Version 2, Appendix C.1 Global parameters
cospfMaxAgeLsa
1.3.6.1.4.1.9.10.101.0.6
A cospfMaxAgeLsa trap signifies that one of
the Opaque LSAs in the router's link-state database has aged to MaxAge.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
ospfLsdbAreaId
1.3.6.1.2.1.14.4.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The 32-bit identifier of the area from which the LSA was received. Reference: OSPF Version 2, Appendix C.2 Area parameters
The type of the link state advertisement. Each link state type has a separate advertisement format. Reference: OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header The OSPF Opaque LSA Option (RFC 2370)
ospfLsdbLsid
1.3.6.1.2.1.14.4.1.3
IpAddress SIZE (4)
The Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. Reference: OSPF Version 2, Section 12.1.4 Link State ID
The type of the link state advertisement. Each link state type has a separate advertisement format. Reference: OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header The OSPF Opaque LSA Option (RFC 2370)
ospfLsdbRouterId
1.3.6.1.2.1.14.4.1.4
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
The 32-bit number that uniquely identifies the originating router in the Autonomous System. Reference: OSPF Version 2, Appendix C.1 Global parameters
cospfNssaTranslatorStatusChange
1.3.6.1.4.1.9.10.101.0.7
A cospfNssaTranslatorStatusChange trap indicates that there has been a change in the router's ability to translate OSPF type-7 LSAs into OSPF type-5 LSAs. This trap should be generated when the Translator Status transitions from or to any defined status on a per area basis.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
ospfAreaId
1.3.6.1.2.1.14.2.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone. Reference: OSPF Version 2, Appendix C.2 Area parameters
Indicates if and how an NSSA Border router is performing NSSA translation of type-7 LSAs into type-5 LSAs. When this object set to enabled, the NSSA Border router's cospfAreaNssaExtTranslatorRole has been set to always. When this object is set to elected, a candidate NSSA Border router is Translating type-7 LSAs into type-5. When this object is set to disabled, a candidate NSSA Border router is NOT translating type-7 LSAs into type-5.
cospfShamLinkStateChange
1.3.6.1.4.1.9.10.101.0.8
A ospfShamLinkStateChange trap signifies that there has been a change in the state of a Sham
Link OSPF interface. This trap should be generated
when the interface state regresses from Point-to-Point
to Down or progresses to Down to Point-to-Point. This trap has been deprecated by cospfShamLinksStateChange.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
cospfShamLinkAreaId
1.3.6.1.4.1.9.10.99.6.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0
cospfShamLinkLocalIpAddress
1.3.6.1.4.1.9.10.99.6.1.2
IpAddress SIZE (4)
The Local IP address of the sham link.
cospfShamLinkNeighborId
1.3.6.1.4.1.9.10.99.6.1.3
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
The Router ID of the other end router of the sham link.
cospfShamLinkState
1.3.6.1.4.1.9.10.99.6.1.7
INTEGER1 = down4 = pointToPoint · Integer32
OSPF sham link states.
cospfShamLinkNbrStateChange
1.3.6.1.4.1.9.10.101.0.9
A cospfShamLinkNbrStateChange trap signifies that there has been a change in the state of a sham link OSPF neighbor. This trap should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full).
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
cospfShamLinkNbrArea
1.3.6.1.4.1.9.10.99.10.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The area to which the sham link is part of.
cospfShamLinksLocalIpAddrType
1.3.6.1.4.1.9.10.99.11.1.2
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's local IP address.
cospfShamLinksLocalIpAddr
1.3.6.1.4.1.9.10.99.11.1.3
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The Local IP address of the sham link.
cospfShamLinkNbrIpAddrType
1.3.6.1.4.1.9.10.99.10.1.2
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link neighbor's IP address.
cospfShamLinkNbrIpAddr
1.3.6.1.4.1.9.10.99.10.1.3
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The IP address this sham link neighbor is using.
cospfShamLinkNbrRtrId
1.3.6.1.4.1.9.10.99.10.1.4
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the neighboring router.
The state of this sham link neighbor relation- ship. Reference: OSPF Version 2, Section 10.1 Neighbor states.
cospfShamLinkConfigError
1.3.6.1.4.1.9.10.101.0.10
A cospfShamLinkConfigError signifies that a packet has been received on a sham link from a router whose configuration parameters conflict with this router's configuration parameters.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
cospfShamLinksAreaId
1.3.6.1.4.1.9.10.99.11.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The area that this sham link is part of.
cospfShamLinksLocalIpAddrType
1.3.6.1.4.1.9.10.99.11.1.2
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's local IP address.
cospfShamLinksLocalIpAddr
1.3.6.1.4.1.9.10.99.11.1.3
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The Local IP address of the sham link.
cospfShamLinksRemoteIpAddrType
1.3.6.1.4.1.9.10.99.11.1.4
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's remote IP address.
cospfShamLinksRemoteIpAddr
1.3.6.1.4.1.9.10.99.11.1.5
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The IP address of the other end router of the sham link.
Potential types of configuration conflicts.
Used by the cospfConfigError and cospfConfigVirtError
traps. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as noError.
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
cospfShamLinkAuthFailure
1.3.6.1.4.1.9.10.101.0.11
A cospfShamLinkAuthFailure trap signifies that a packet has been received on a sham link from a router whose authentication key or authentication type conflicts with this router's authentication key and authentication type.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
cospfShamLinksAreaId
1.3.6.1.4.1.9.10.99.11.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The area that this sham link is part of.
cospfShamLinksLocalIpAddrType
1.3.6.1.4.1.9.10.99.11.1.2
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's local IP address.
cospfShamLinksLocalIpAddr
1.3.6.1.4.1.9.10.99.11.1.3
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The Local IP address of the sham link.
cospfShamLinksRemoteIpAddrType
1.3.6.1.4.1.9.10.99.11.1.4
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's remote IP address.
cospfShamLinksRemoteIpAddr
1.3.6.1.4.1.9.10.99.11.1.5
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The IP address of the other end router of the sham link.
Potential types of configuration conflicts.
Used by the cospfConfigError and cospfConfigVirtError
traps. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as noError.
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
cospfShamLinkRxBadPacket
1.3.6.1.4.1.9.10.101.0.12
A cospfShamLinkRxBadPacket trap signifies that an OSPF packet has been received on a sham link that cannot be parsed.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
cospfShamLinksAreaId
1.3.6.1.4.1.9.10.99.11.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The area that this sham link is part of.
cospfShamLinksLocalIpAddrType
1.3.6.1.4.1.9.10.99.11.1.2
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's local IP address.
cospfShamLinksLocalIpAddr
1.3.6.1.4.1.9.10.99.11.1.3
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The Local IP address of the sham link.
cospfShamLinksRemoteIpAddrType
1.3.6.1.4.1.9.10.99.11.1.4
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's remote IP address.
cospfShamLinksRemoteIpAddr
1.3.6.1.4.1.9.10.99.11.1.5
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The IP address of the other end router of the sham link.
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
cospfShamLinkTxRetransmit
1.3.6.1.4.1.9.10.101.0.13
A cospfShamLinkTxRetransmit trap signifies that an OSPF packet has been retransmitted on a sham link. All packets that may be retransmitted are associated with an LSDB entry. The LS type, LS ID, and Router ID are used identify the LSDB entry.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
cospfShamLinksAreaId
1.3.6.1.4.1.9.10.99.11.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The area that this sham link is part of.
cospfShamLinksLocalIpAddrType
1.3.6.1.4.1.9.10.99.11.1.2
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's local IP address.
cospfShamLinksLocalIpAddr
1.3.6.1.4.1.9.10.99.11.1.3
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The Local IP address of the sham link.
cospfShamLinksRemoteIpAddrType
1.3.6.1.4.1.9.10.99.11.1.4
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's remote IP address.
cospfShamLinksRemoteIpAddr
1.3.6.1.4.1.9.10.99.11.1.5
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The IP address of the other end router of the sham link.
OSPF packet types. When the last value of a trap using this object is needed, but no traps of that type have been sent, this value pertaining to this object should be returned as nullPacket.
The type of the link state advertisement. Each link state type has a separate advertisement format. Reference: OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header The OSPF Opaque LSA Option (RFC 2370)
ospfLsdbLsid
1.3.6.1.2.1.14.4.1.3
IpAddress SIZE (4)
The Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. Reference: OSPF Version 2, Section 12.1.4 Link State ID
ospfLsdbRouterId
1.3.6.1.2.1.14.4.1.4
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
The 32-bit number that uniquely identifies the originating router in the Autonomous System. Reference: OSPF Version 2, Appendix C.1 Global parameters
cospfShamLinksStateChange
1.3.6.1.4.1.9.10.101.0.14
A ospfShamLinkStateChange trap signifies that there has been a change in the state of a Sham
Link OSPF interface. This trap should be generated
when the interface state regresses from Point-to-Point
to Down or progresses to Down to Point-to-Point.
ospfRouterId
1.3.6.1.2.1.14.1.1
RouterIDA OSPF Router Identifier. Note that the Router ID, in OSPF, has the same format as an IP address, but identifies the router independent of its IP address. SIZE (4) · IpAddress
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
This object is persistent and when written the entity SHOULD save the change to non-volatile storage. Reference: OSPF Version 2, C.1 Global parameters
cospfShamLinksAreaId
1.3.6.1.4.1.9.10.99.11.1.1
AreaIDAn OSPF Area Identifier. Note that the Area ID, in OSPF, has the same format as an IP address, but has the function of defining a summarization point for link state advertisements. SIZE (4) · IpAddress
The area that this sham link is part of.
cospfShamLinksLocalIpAddrType
1.3.6.1.4.1.9.10.99.11.1.2
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's local IP address.
cospfShamLinksLocalIpAddr
1.3.6.1.4.1.9.10.99.11.1.3
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The Local IP address of the sham link.
cospfShamLinksRemoteIpAddrType
1.3.6.1.4.1.9.10.99.11.1.4
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType.
To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation.
Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of internet address of this sham link's remote IP address.
cospfShamLinksRemoteIpAddr
1.3.6.1.4.1.9.10.99.11.1.5
InetAddressDenotes a generic Internet address.
An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row.
The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error.
When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
The IP address of the other end router of the sham link.