CISCO-PPPOE-MIB

Gauge32 · sessions

The current number of active PPPoE sessions within this system.

Unsigned32 · sessions

Maximum number of allowed PPPoE sessions within the system.

Unsigned32 · sessions

Threshold value of the established PPPoE sessions within the system. Default value is equal to cPppoeSystemMaxSessionsConfigurable

Gauge32 · sessions

The current number of active PPPoE sessions on the VCL.

Unsigned32 · sessions

The maximum number of allowed PPPoE sessions on the VCL.

Unsigned32 · sessions

The Threshold value of the established PPPoE sessions on the VCL. Default value is equal to cPppoeVcMaxAllowedSessions.

Unsigned32

This object provides limit on number of PPPoE sessions for a single client Ethernet MAC address. If the limit is reached new session request from the client would be denied

MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:

The client MAC address that is referred as a part of the notification information. Example: cPppoeSystemSessionPerMACLimitNotif

Unsigned32

This object provides the rate limit at which PPPoE session were created from a single client MAC address. During a configured time interval, once the number of new session requests coming from a particular client MAC address reaches this limit, it's expected to have delay in response for those clients.

MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:

The client MAC address that is referred as a part of the notification information. Example: cPppoeSystemSessionPerMACLimitNotif

Unsigned32

This object provides limit on number of PPPoE sessions on a particular Vlan. If the limit is reached new session request on this vlan would be denied.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

VlanIdThe VLAN-ID that uniquely identifies a VLAN. This is the 12-bit VLAN-ID used in the VLAN Tag header. The range is defined by the REFERENCEd specification.Reference: IEEE Std 802.1Q 2003 Edition, Virtual Bridged Local Area Networks. (1..4094) · Integer32 · hint d

The Vlan ID of PPPoE session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVLANLimitNotif

VlanIndexA value used to index per-VLAN tables: values of 0 and 4095 are not permitted. If the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095, then it represents a VLAN with scope local to the particular agent, i.e., one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q, but it is convenient to be able to manage them in the same way using this MIB. · Unsigned32 · hint d

The inner Vlan ID of PPPoE QinQ session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVLANLimitNotif

Unsigned32

This object provides the rate limit at which PPPoE session were created on a Vlan. During a configured time interval once the number of new session requests coming on a particular Vlan reaches this limit, it's expected to have delay in response for client on this Vlan.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

VlanIdThe VLAN-ID that uniquely identifies a VLAN. This is the 12-bit VLAN-ID used in the VLAN Tag header. The range is defined by the REFERENCEd specification.Reference: IEEE Std 802.1Q 2003 Edition, Virtual Bridged Local Area Networks. (1..4094) · Integer32 · hint d

The Vlan ID of PPPoE session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVLANLimitNotif

VlanIndexA value used to index per-VLAN tables: values of 0 and 4095 are not permitted. If the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095, then it represents a VLAN with scope local to the particular agent, i.e., one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q, but it is convenient to be able to manage them in the same way using this MIB. · Unsigned32 · hint d

The inner Vlan ID of PPPoE QinQ session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVLANLimitNotif

Unsigned32

This object provides limit on number of PPPoE sessions on a particular ATM-VC. If the limit is reached new session request on this VC would be denied.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

AtmVcIdentifierThe VCI value for a VCL. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB. (0..65535) · Integer32

The ATM VCI of PPPoE session that is referred as a part of the notification information. Example:cPppoeSystemSessionPerVCLimitTrap

AtmVpIdentifierThe VPI value for a VPL or VCL. The value VPI=0 is only allowed for a VCL. For ATM UNIs supporting VPCs the VPI value ranges from 0 to 255. The VPI value 0 is supported for ATM UNIs conforming to the ATM Forum UNI 4.0 Annex 8 (Virtual UNIs) specification. For ATM UNIs supporting VCCs the VPI value ranges from 0 to 255. For ATM NNIs the VPI value ranges from 0 to 4095. The maximum VPI value cannot exceed the value allowable by atmInterfaceMaxVpiBits defined in ATM-MIB. (0..4095) · Integer32

The ATM VPI of PPPoE session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVCLimitTrap

Unsigned32

This object provides the rate limit at which PPPoE session were created on an ATM-VC. During a configured time interval, once the number of new session requests coming on an ATM-VC reaches this limit, it's expected to have delay in response for those clients on this VC.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

AtmVcIdentifierThe VCI value for a VCL. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB. (0..65535) · Integer32

The ATM VCI of PPPoE session that is referred as a part of the notification information. Example:cPppoeSystemSessionPerVCLimitTrap

AtmVpIdentifierThe VPI value for a VPL or VCL. The value VPI=0 is only allowed for a VCL. For ATM UNIs supporting VPCs the VPI value ranges from 0 to 255. The VPI value 0 is supported for ATM UNIs conforming to the ATM Forum UNI 4.0 Annex 8 (Virtual UNIs) specification. For ATM UNIs supporting VCCs the VPI value ranges from 0 to 255. For ATM NNIs the VPI value ranges from 0 to 4095. The maximum VPI value cannot exceed the value allowable by atmInterfaceMaxVpiBits defined in ATM-MIB. (0..4095) · Integer32

The ATM VPI of PPPoE session that is referred as a part of the notification information. Example: cPppoeSystemSessionPerVCLimitTrap

Unsigned32

This object is used to monitor number of active PPPoE sessions above a healthy watermark. If number of PPPoE sessions falls below this watermark then we can expect something wrong happened. So we send out trap to user indicating session loss below watermark.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

Unsigned32

This object is used to monitor number of active PPPoE sessions, initiated from a particular physical interface. The sssion count is accumulation of all the pppoe session came on a physical and its sub-interfaces. If this count drops below this object water mark, we expect some problem and send out trap indicating drop of sessions below watermark.

PercentAn integer that is in the range of a percent value. (0..100) · Integer32

This object is used to monitor the percentage of PPPoE sessions going down at a configured time interval. During a time interval if percentage of PPPoE sessions lost, falls above this object value, we send trap indicating loss of sessions above percentage expected.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

Unsigned32

This object is used to monitor the percentage of PPPoE sessions loss on a particular physical interface including all of its sub-interfaces. If during a configured interval of time, percentage of PPPoE sessions lost on a physical interface is above this object value we send a trap.