CISCO-PSA-MICROCODE-MIB

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

The textual name of the physical entity. The value of this object should be the name of the component as assigned by the local device and should be suitable for use in commands entered at the device's 'console'. This might be a text name (e.g., 'console') or a simple component number (e.g., port or module number, such as '1'), depending on the physical component naming syntax of the device. If there is no local name, or if this object is otherwise not applicable, then this object contains a zero-length string. Note that the value of entPhysicalName for two physical entities will be the same in the event that the console interface does not distinguish between them, e.g., slot-1 and the card in slot-1.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

A textual description of physical entity. This object should contain a string that identifies the manufacturer's name for the physical entity and should be set to a distinct value for each version or model of the physical entity.

PsaMicrocodeBundleId1 = unknown2 = none3 = vanillaPOS4 = vanillaGE5 = vanillaInuit6 = vanillaTaz7 = pircPOS8 = pircGE9 = uRPFPOS10 = vrfSelectionPOS11 = bgppaPOS12 = bgppaGE13 = ipColorPOS14 = inputAcl128POS15 = inputAcl128GE16 = outputAcl128POS17 = outputAcl128GE18 = inputAcl448POS19 = inputAcl448GE20 = outputAcl448POS21 = outputAcl448GE22 = serverCard23 = eoMplsGE24 = frtpPOS25 = outputAclATM26 = inputAcl128Taz27 = vrfSelectionGE28 = uRPFGE29 = cscGE30 = linkBundleSMPOS31 = linkBundleDMPOS32 = linkBundleSMGE33 = linkBundleDMGEThe identity of a PSA microcode bundle. The current microcode bundles are: unknown(1): Unknown Bundle. There will be no entry associated with this value in the cpmcBundleTable. none(2): This value is used by cpmcModulePsaPrevBundleId object till the first micrcode reload occurs on the psa. There will be no entry associated with this value in the cpmcBundleTable. vanillaPOS(3): POS Vanilla vanillaGE(4): GE Vanilla vanillaInuit(5): Inuit Vanilla vanillaTaz(6): TAZ Vanilla pircPOS(7): POS Per Interface Rate Control pircGE(8): GE Per Interface Rate Control uRPFPOS(9): POS Unicast Reverse Path Forwarding vrfSelectionPOS(10): POS VRF Selection bgppaPOS(11): POS BGP Policy Accounting bgppaGE(12): GE BGP Policy Accounting ipColorPOS(13): POS IP Coloring inputAcl128POS(14): POS 128 Line Input ACL inputAcl128GE(15): GE 128 Line Input ACL outputAcl128POS(16): POS 128 Line Output ACL outputAcl128GE(17): GE 128 Line Output ACL inputAcl448POS(18): POS 448 Line Input ACL inputAcl448GE(19): GE 448 Line Input ACL outputAcl448POS(20): POS 448 Line Output ACL outputAcl448GE(21): GE 448 Line Output ACL serverCard(22): Server Card eoMplsGE(23): GE Ethernet over MPLS frtpPOS(24): POS Frame Relay Traffic Policing outputAclATM(25): ATM Output ACL inputAcl128Taz(26): TAZ 128 Line Input ACL vrfSelectionGE(27): GE VRF Selection uRPFGE(28): GE Unicast Reverse Path Forwarding cscGE(29): GE Carrier Supporting Carriers linkBundleSMPOS(30): POS Link Bundle Single Mode linkBundleDMPOS(31): POS Link Bundle Double Mode linkBundleSMGE(32): GE Link Bundle Single Mode linkBundleDMGE(33): GE Link Bundle Double Mode · Integer32

The identity of the microcode bundle currently loaded on the PSA of the module identified by entPhysicalIndex.

PsaMicrocodeBundleId1 = unknown2 = none3 = vanillaPOS4 = vanillaGE5 = vanillaInuit6 = vanillaTaz7 = pircPOS8 = pircGE9 = uRPFPOS10 = vrfSelectionPOS11 = bgppaPOS12 = bgppaGE13 = ipColorPOS14 = inputAcl128POS15 = inputAcl128GE16 = outputAcl128POS17 = outputAcl128GE18 = inputAcl448POS19 = inputAcl448GE20 = outputAcl448POS21 = outputAcl448GE22 = serverCard23 = eoMplsGE24 = frtpPOS25 = outputAclATM26 = inputAcl128Taz27 = vrfSelectionGE28 = uRPFGE29 = cscGE30 = linkBundleSMPOS31 = linkBundleDMPOS32 = linkBundleSMGE33 = linkBundleDMGEThe identity of a PSA microcode bundle. The current microcode bundles are: unknown(1): Unknown Bundle. There will be no entry associated with this value in the cpmcBundleTable. none(2): This value is used by cpmcModulePsaPrevBundleId object till the first micrcode reload occurs on the psa. There will be no entry associated with this value in the cpmcBundleTable. vanillaPOS(3): POS Vanilla vanillaGE(4): GE Vanilla vanillaInuit(5): Inuit Vanilla vanillaTaz(6): TAZ Vanilla pircPOS(7): POS Per Interface Rate Control pircGE(8): GE Per Interface Rate Control uRPFPOS(9): POS Unicast Reverse Path Forwarding vrfSelectionPOS(10): POS VRF Selection bgppaPOS(11): POS BGP Policy Accounting bgppaGE(12): GE BGP Policy Accounting ipColorPOS(13): POS IP Coloring inputAcl128POS(14): POS 128 Line Input ACL inputAcl128GE(15): GE 128 Line Input ACL outputAcl128POS(16): POS 128 Line Output ACL outputAcl128GE(17): GE 128 Line Output ACL inputAcl448POS(18): POS 448 Line Input ACL inputAcl448GE(19): GE 448 Line Input ACL outputAcl448POS(20): POS 448 Line Output ACL outputAcl448GE(21): GE 448 Line Output ACL serverCard(22): Server Card eoMplsGE(23): GE Ethernet over MPLS frtpPOS(24): POS Frame Relay Traffic Policing outputAclATM(25): ATM Output ACL inputAcl128Taz(26): TAZ 128 Line Input ACL vrfSelectionGE(27): GE VRF Selection uRPFGE(28): GE Unicast Reverse Path Forwarding cscGE(29): GE Carrier Supporting Carriers linkBundleSMPOS(30): POS Link Bundle Single Mode linkBundleDMPOS(31): POS Link Bundle Double Mode linkBundleSMGE(32): GE Link Bundle Single Mode linkBundleDMGE(33): GE Link Bundle Double Mode · Integer32

The identity of the microcode bundle previously loaded on the PSA of the module identified by entPhysicalIndex. Till the first microcode reload is performed on the module, the value will be 'none(2)'.

PsaMicrocodeFeaturesThe list of features supported on a PSA microcode bundle. The current list of features are: basicIpForwarding(0): Basic IP Forwarding basicMplsSwitching(1): Basic MPLS Switching frameRelaySwitching(2): Frame Relay Switching eAFrSwitching(3): Extended Addressing FR Switching frtp(4): Frame Relay Traffic Policing pirc(5): PIRC vrfSelection(6): VRF Selection uRPF(7): Unicast RPF inputAcl128(8): 128 Line Input ACLs outputAcl128(9): 128 Line Output ACLs inputAcl448(10): 448 Line Input ACLs outputAcl448(11): 448 Line Output ACLs. sampledNetflow(12): Sampled Netflow ipMarking(13): IP Marking bgppa(14): BGP Policy Accounting uti(15): Universal Transport Interface mplsVpn(16): MPLS VPN eoMpls(17): Ethernet over MPLS atmoMpls(18): ATM over MPLS csc(19): Carrier Supporting Carriers multicast(20): Multicast perPacketLoadBalancing(21): Per Packet Load Balancing sourceMacAccounting(22): Source MAC Accounting frSubVrf(23): FR per-subinterface VRF processing serverCard(24): Server Card mplsSNF(25): MPLS aware Sampled Netflow linkBundle(26): Link Bundle atomDisposition(27): AToM Disposition · BITS

The list of features newly enabled due to the loading of the microcode bundle identified by cpmcModulePsaCurrBundleId.

PsaMicrocodeFeaturesThe list of features supported on a PSA microcode bundle. The current list of features are: basicIpForwarding(0): Basic IP Forwarding basicMplsSwitching(1): Basic MPLS Switching frameRelaySwitching(2): Frame Relay Switching eAFrSwitching(3): Extended Addressing FR Switching frtp(4): Frame Relay Traffic Policing pirc(5): PIRC vrfSelection(6): VRF Selection uRPF(7): Unicast RPF inputAcl128(8): 128 Line Input ACLs outputAcl128(9): 128 Line Output ACLs inputAcl448(10): 448 Line Input ACLs outputAcl448(11): 448 Line Output ACLs. sampledNetflow(12): Sampled Netflow ipMarking(13): IP Marking bgppa(14): BGP Policy Accounting uti(15): Universal Transport Interface mplsVpn(16): MPLS VPN eoMpls(17): Ethernet over MPLS atmoMpls(18): ATM over MPLS csc(19): Carrier Supporting Carriers multicast(20): Multicast perPacketLoadBalancing(21): Per Packet Load Balancing sourceMacAccounting(22): Source MAC Accounting frSubVrf(23): FR per-subinterface VRF processing serverCard(24): Server Card mplsSNF(25): MPLS aware Sampled Netflow linkBundle(26): Link Bundle atomDisposition(27): AToM Disposition · BITS

The list of features disabled because of the unloading of microcode bundle identified by cpmcModulePsaPrevBundleId and loading of the microcode bundle identified by cpmcModulePsaCurrBundleId.