2015-09-21
This MIB module represents the Qam-Partition (QP) and Load Balance Group (LBG) parameters in the headend and it is supported by an snmp agent. It defines objects for managing both QP and LBG.
Download CISCO-QP-LBG-MIB.txt Open CISCO-QP-LBG-MIB.txt in a new tab
SCALARS (4) · TABLES (3) · TRAPS (6)
| Name | OID |
|---|---|
| cqlQpNotifyEnable | 1.3.6.1.4.1.9.9.824.1.4 |
| cqlQamNotifyEnable | 1.3.6.1.4.1.9.9.824.1.5 |
| cqlRouteNotifyEnable | 1.3.6.1.4.1.9.9.824.1.6 |
| cqlQamOverSubscribedEnable | 1.3.6.1.4.1.9.9.824.1.7 |
| Name | OID |
|---|---|
| cqlqamPartitionTable | 1.3.6.1.4.1.9.9.824.1.1 |
| cqlloadBalanceGroupTable | 1.3.6.1.4.1.9.9.824.1.2 |
| cqllbgrouteTable | 1.3.6.1.4.1.9.9.824.1.3 |
END OF TOC
1.3.6.1.4.1.9.9.824.1.4
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object specifies whether the system generates cqlQpStateChange notifications. A false value will prevent cqlQpStateChange notifications from being generated by this system.
1.3.6.1.4.1.9.9.824.1.5
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object specifies whether the system generates cqlQamAdd or cqlQamDelete notifications. A false value will prevent cqlQamAdd or cqlQamDelete notifications from being generated by this system.
1.3.6.1.4.1.9.9.824.1.6
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object specifies whether the system produces cqlRouteAdd or cqlRouteDelete notifications. A false value will prevent cqlRouteAdd or cqlRouteDelete notifications from being generated by this system.
1.3.6.1.4.1.9.9.824.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object specifies whether the system produces cqlQamOverSubscribedAlert notifications. A false value will prevent cqlQamOverSubscribedAlert notifications from being generated by the system.
1.3.6.1.4.1.9.9.824.1.1
Index: cqlqpIndex
This table describes the various parameters of QP such as QP's state, protocol, management IP, server IP, server state, information related to qam and video routes.
1.3.6.1.4.1.9.9.824.1.1.1.1
Unsigned32
Table Index. This index uniquely identifies the QP.
1.3.6.1.4.1.9.9.824.1.1.1.2
Unsigned32
This object specifies the QP Id.
1.3.6.1.4.1.9.9.824.1.1.1.3
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention. ipv4z(3) A non-global IPv4 address including a zone index as defined by the InetAddressIPv4z textual convention. ipv6z(4) A non-global IPv6 address including a zone index as defined by the InetAddressIPv6z textual convention. dns(16) A DNS domain name as defined by the InetAddressDNS textual convention. Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType. To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of the Management address as defined inetAddressType. The supported address types are IPv4 and IPv6.
1.3.6.1.4.1.9.9.824.1.1.1.4
InetAddressDenotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row. The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
This object specifies the Management IP address of a QP.
1.3.6.1.4.1.9.9.824.1.1.1.5
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention. ipv4z(3) A non-global IPv4 address including a zone index as defined by the InetAddressIPv4z textual convention. ipv6z(4) A non-global IPv6 address including a zone index as defined by the InetAddressIPv6z textual convention. dns(16) A DNS domain name as defined by the InetAddressDNS textual convention. Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType. To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of the Server address as defined inetAddressType. The supported address types are IPv4 and IPv6.
1.3.6.1.4.1.9.9.824.1.1.1.6
InetAddressDenotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row. The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
Server IP of the QP.
1.3.6.1.4.1.9.9.824.1.1.1.7
INTEGER1 = inactive2 = init3 = active · Integer32
This object specifies the state of the QP. The following are the valid states. inactive(1) QP is in inactive state. init(2) QP is in init state. active(3) QP is in active state.
1.3.6.1.4.1.9.9.824.1.1.1.8
INTEGER1 = gqi2 = ermi · Integer32
This object specifies the QP Protocol. Gqi(1) Ermi(2)
1.3.6.1.4.1.9.9.824.1.1.1.9
Unsigned32 · seconds
This object specifies the keepalive timer in seconds for a QP.
1.3.6.1.4.1.9.9.824.1.1.1.10
INTEGER1 = disconnected2 = connected · Integer32
This object specifies the Server state of the QP. disconnected(1) Server is in disconnected state. connected(2) Server is in connected state.
1.3.6.1.4.1.9.9.824.1.1.1.11
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
This object specifies the MAC address of a QP, applicable only for GQI Protocol.
1.3.6.1.4.1.9.9.824.1.1.1.12
Unsigned32 · seconds
This object specifies Reset interval for a QP. It is applicable only for GQI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.13
Unsigned32
The total number of qams associated with the QP.
1.3.6.1.4.1.9.9.824.1.1.1.14
OCTET STRING
This object specifies the list of Qam carriers associated with the QP.
1.3.6.1.4.1.9.9.824.1.1.1.15
Unsigned32
The total number of routes associated with the QP.
1.3.6.1.4.1.9.9.824.1.1.1.16
OCTET STRING
Route details of the QP. It includes the configured IP and also the highest and lowest UDP range.
1.3.6.1.4.1.9.9.824.1.1.1.17
OCTET STRING
Component Name for the QP, applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.18
OCTET STRING
Streaming zone for the QP, applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.19
Unsigned32 · seconds
Hold Time in seconds for the QP, applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.20
Unsigned32 · seconds
Connect Time in seconds for the QP, applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.21
Unsigned32 · seconds
Connection retry in seconds for the QP. It is applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.22
Unsigned32 · seconds
Connect time in seconds for the QP. It is applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.23
Unsigned32 · seconds
Connect retry in seconds for the QP, applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.24
Unsigned32 · seconds
Connection timeout in seconds for the QP. It is applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.25
Unsigned32 · seconds
Session Timeout in seconds for the QP. It is applicable only for ERMI protocol.
1.3.6.1.4.1.9.9.824.1.1.1.26
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object specifies oversubscription status of a Qam. The value 'True' indicates the Qam is oversubscribed. Otherwise the value 'False' is reported.
1.3.6.1.4.1.9.9.824.1.1.1.27
OCTET STRING
List of Server IP's for the QP.
1.3.6.1.4.1.9.9.824.1.2
Index: entPhysicalIndex · cqllbgIndex
This table describes the total bandwidth and the reserved bandwidth of QAM/IP based sessions.
from ENTITY-MIB
PhysicalIndexAn arbitrary value that uniquely identifies the physical entity. The value should be a small positive integer. Index values for different physical entities are not necessarily contiguous. (1..2147483647) · Integer32 · hint d
The index for this entry.
1.3.6.1.4.1.9.9.824.1.2.1.1
Unsigned32
This index is to identify the LBG group within the slot.
1.3.6.1.4.1.9.9.824.1.2.1.2
Unsigned32 · Kbps
This object specifies the total bandwidth in Kbps of a LBG.
1.3.6.1.4.1.9.9.824.1.2.1.3
Unsigned32 · Kbps
This object specifies the total reserved bandwidth in Kbps for depi sessions.
1.3.6.1.4.1.9.9.824.1.2.1.4
Unsigned32 · Kbps
This object specifies the total reserved bandwidth in Kbps for video sessions.
1.3.6.1.4.1.9.9.824.1.2.1.5
Unsigned32 · Kbps
This object specifies the available bandwidth in Kbps. This may be calculated as (TotalBandwidth - (QamRsvBandwidth + IpRsvBandwith)).
1.3.6.1.4.1.9.9.824.1.3
Index: entPhysicalIndex · cqllbgRouteIndex
This table describes the route parameters such as QP id,destination ip, low and high udp range, reserved and allocated bandwidth.
from ENTITY-MIB
PhysicalIndexAn arbitrary value that uniquely identifies the physical entity. The value should be a small positive integer. Index values for different physical entities are not necessarily contiguous. (1..2147483647) · Integer32 · hint d
The index for this entry.
1.3.6.1.4.1.9.9.824.1.3.1.1
Unsigned32
The table index. This is the index which uniquely identifies the route within the LBG group.
1.3.6.1.4.1.9.9.824.1.3.1.2
Unsigned32
This object specifies the QP ID. The range of the QP is between 1 and 50.
1.3.6.1.4.1.9.9.824.1.3.1.3
InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention. ipv4z(3) A non-global IPv4 address including a zone index as defined by the InetAddressIPv4z textual convention. ipv6z(4) A non-global IPv6 address including a zone index as defined by the InetAddressIPv6z textual convention. dns(16) A DNS domain name as defined by the InetAddressDNS textual convention. Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType. To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32
The type of the destination address as defined inetAddressType. The supported address types are IPv4 and IPv6.
1.3.6.1.4.1.9.9.824.1.3.1.4
InetAddressDenotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row. The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING
Destination IP address of the route to which the incoming packets are routed to.
1.3.6.1.4.1.9.9.824.1.3.1.5
Unsigned32
The lowest UDP port of the UDP port range that can be used.
1.3.6.1.4.1.9.9.824.1.3.1.6
Unsigned32
The highest UDP port of the UDP port range that can be used.
1.3.6.1.4.1.9.9.824.1.3.1.7
Unsigned32
Ingress port of a QP, applicable only for GQI protocol.
1.3.6.1.4.1.9.9.824.1.3.1.8
Unsigned32 · Kbps
Reserved bandwidth is the total bitrate reserved on this route in Kbps.
1.3.6.1.4.1.9.9.824.1.3.1.9
Unsigned32 · Kbps
The total bandwidth being used by sessions using this route in Kbps.
1.3.6.1.4.1.9.9.824.1.3.1.10
Unsigned32
Number of sessions currently use this route to forward this traffic in Kbps.
1.3.6.1.4.1.9.9.824.0.1
The device generates this notification when a QP state has changed and the value of cqlQpNotifyEnable is 'true'.
1.3.6.1.4.1.9.9.824.1.1.1.7
INTEGER1 = inactive2 = init3 = active · Integer32
This object specifies the state of the QP. The following are the valid states. inactive(1) QP is in inactive state. init(2) QP is in init state. active(3) QP is in active state.
1.3.6.1.4.1.9.9.824.0.2
The device generates this notification when a qam has been added to QP and the value of cqlQamNotifyEnable is 'true'.
1.3.6.1.4.1.9.9.824.1.1.1.2
Unsigned32
This object specifies the QP Id.
1.3.6.1.2.1.2.2.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
1.3.6.1.4.1.9.9.824.0.3
The device generates this notification when a qam has been deleted from QP and the value of cqlQamNotifyEnable is 'true'.
1.3.6.1.4.1.9.9.824.1.1.1.2
Unsigned32
This object specifies the QP Id.
1.3.6.1.2.1.2.2.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
1.3.6.1.4.1.9.9.824.0.4
The device generates this notification when a route has been added to QP and the value of cqlRouteNotifyEnable is 'true'.
1.3.6.1.4.1.9.9.824.1.1.1.16
OCTET STRING
Route details of the QP. It includes the configured IP and also the highest and lowest UDP range.
1.3.6.1.4.1.9.9.824.0.5
The device generates this notification when a route has been deleted from QP and the value of cqlRouteNotifyEnable is 'true'.
1.3.6.1.4.1.9.9.824.1.1.1.16
OCTET STRING
Route details of the QP. It includes the configured IP and also the highest and lowest UDP range.
1.3.6.1.4.1.9.9.824.0.6
The device generates this notification when a qam has been oversubscribed or cleared. This will be enabled when the object cqlQamOverSubscribedEnable is set to 'true'.
1.3.6.1.2.1.2.2.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
1.3.6.1.4.1.9.9.824.1.1.1.26
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object specifies oversubscription status of a Qam. The value 'True' indicates the Qam is oversubscribed. Otherwise the value 'False' is reported.