CISCO-TELEPRESENCE-MIB

Unsigned32

This object specifies a unique index for a peripheral which is attached to a Telepresence system.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

This object specifies a description of the attached peripheral. Peripheral description may be the peripheral type, model and/or version information or a peripheral signal description.

CtpPeripheralStatusCode0 = noError1 = other2 = cableError3 = powerError4 = mgmtSysConfigError5 = systemError6 = deviceError7 = linkError8 = commError9 = detectionDisabledThe textual convention identifies the peripheral status. noError (0) -- Expected peripheral device is functioning through the attached port. other (1) -- None of the listed state. cableError (2) -- Expected peripheral device has cabling issue. powerError (3) -- Expected peripheral device has power issue. mgmtSysConfigError (4) -- Expected peripheral device has communications management system configuration issue. systemError (5) -- Telepresence system error. deviceError (6) -- Expected peripheral device is attached but not fully functional. linkError (7) -- Expected peripheral device has port level link issue. commError (8) -- Expected peripheral device has port level communication issue. detectionDisabled (9) -- Status detection has been disabled. · Integer32

This object specifies a peripheral status.

CtpPeripheralDeviceCategoryCode0 = unknown1 = other2 = uplinkDevice3 = ipPhone4 = camera5 = display6 = secCodec7 = docCamera8 = projector9 = dviDevice10 = presentationCodec11 = auxiliaryControlUnit12 = audioExpansionUnit13 = microphone14 = headset15 = positionMic16 = digitialMediaSystem17 = auxHDMIOutputDevice18 = uiDevice19 = auxHDMIInputDevice20 = bringYourOwnDeviceThe textual convention identifies the peripheral type. unknown (0) -- Unknown Device other (1) -- None of the listed device uplinkDevice (2) -- Device attached to CTS uplink port ipPhone (3) -- IP phone camera (4) -- Camera display (5) -- Display secCodec (6) -- CTS secondary codec docCamera (7) -- Document camera projector (8) -- Projector dviDevice (9) -- Device attached to DVI port presentationCodec (10) -- CTS codec process presentation -- stream auxiliaryControlUnit (11) -- Auxiliary control unit audioExpansionUnit (12) -- Audio expansion unit microphone (13) -- Microphone headset (14) -- Headset positionMic (15) -- Position microphone digitalMediaSystem (16) -- Digitial Media System auxHDMIOuputDevice (17) -- Auxiliary HDMI output device uiDevice (18) -- User Interface device for CTS auxHDMIInputDevice (19) -- HDMI input enabled device bringYourOwnDevice (20) -- Bring Your Own Device, -- like PC,Laptop,Tablet etc · Integer32

This object specifies a peripheral category of a device.

Unsigned32

This object specifies a device number for a peripheral. Device number is unique within the same peripheral device category.

Unsigned32

This object specifies a unique number for a peripheral Ethernet interface. If no peripheral has more than one Ethernet interface, this object will have value '1'.

InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d

The object specifies an index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex. If this entry doesn't have corresponding ifIndex, then this value will have value '0'.

InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention. ipv4z(3) A non-global IPv4 address including a zone index as defined by the InetAddressIPv4z textual convention. ipv6z(4) A non-global IPv6 address including a zone index as defined by the InetAddressIPv6z textual convention. dns(16) A DNS domain name as defined by the InetAddressDNS textual convention. Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType. To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32

This object specifies the type of address contained in the corresponding instance of ctpEtherPeripheralAddr.

InetAddressDenotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row. The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING

This object specifies the address of the attached peripheral in the format given by the corresponding instance of ctpEtherPeripheralAddrType.

CtpPeripheralStatusCode0 = noError1 = other2 = cableError3 = powerError4 = mgmtSysConfigError5 = systemError6 = deviceError7 = linkError8 = commError9 = detectionDisabledThe textual convention identifies the peripheral status. noError (0) -- Expected peripheral device is functioning through the attached port. other (1) -- None of the listed state. cableError (2) -- Expected peripheral device has cabling issue. powerError (3) -- Expected peripheral device has power issue. mgmtSysConfigError (4) -- Expected peripheral device has communications management system configuration issue. systemError (5) -- Telepresence system error. deviceError (6) -- Expected peripheral device is attached but not fully functional. linkError (7) -- Expected peripheral device has port level link issue. commError (8) -- Expected peripheral device has port level communication issue. detectionDisabled (9) -- Status detection has been disabled. · Integer32

This object specifies attached peripheral status retrieved via Ethernet port.

Unsigned32

This object specifies a unique number for a peripheral HDMI. If no peripheral has more than one HDMI, this object will have value '1'.

CtpPeripheralCableCode1 = plugged2 = loose3 = unplugged4 = unknown5 = internalErrorThe textual convention identifies cable status of the attached peripheral through HDMI. plugged (1) -- Peripheral cable is plugged. loose (2) -- Peripheral cable is loose. unplugged (3) -- Peripheral cable is unplugged. unknown (4) -- Cannot detect peripheral cable status. internalError (5) -- Internal error. · Integer32

This object specifies cable status of an attached peripheral. This object is set to 'loose' if system detects cable is 'unplugged' but power is 'on'.

CtpPeripheralPowerCode1 = on2 = standby3 = off4 = unknown5 = internalErrorThe textual convention identifies power status of the attached peripheral through HDMI. on (1) -- Peripheral power is on. standby (2) -- Peripheral power is in standby mode. off (3) -- Peripheral power is off. unknown (4) -- Cannot detect peripheral power status. internalError (5) -- Internal error. · Integer32

This object specifies power status of an attached peripheral. This object is set to 'unknown' if system detects cable is 'unplugged'.

Unsigned32

This object specifies a unique number for a peripheral DVI. If no peripheral has more than one DVI, this object will have value '1'. Note that some Telepresence systems have no DVI port and some Telepresence systems have only one DVI port.

CtpPeripheralCableCode1 = plugged2 = loose3 = unplugged4 = unknown5 = internalErrorThe textual convention identifies cable status of the attached peripheral through HDMI. plugged (1) -- Peripheral cable is plugged. loose (2) -- Peripheral cable is loose. unplugged (3) -- Peripheral cable is unplugged. unknown (4) -- Cannot detect peripheral cable status. internalError (5) -- Internal error. · Integer32

This object specifies attached device cable status reported by DVI.

Unsigned32

This object specifies a unique number for a peripheral RS-232. If no peripheral has more than one RS-232, this object will have value '1'. Note that some Telepresence systems have no RS-232 port.

InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d

The object specifies an index value that uniquely identifies the RS-232 port to which this entry is applicable. Its value is the same as RS-232-MIB's rs232PortIndex for the port. If RS-232-MIB is not supported by the agent, then this value will have value '0'.

INTEGER1 = connected2 = unknown · Integer32

This object specifies peripheral which is connected via RS232. When the object is 'connected(1)', peripheral connection via RS232 is working properly. When the object is 'unknown(2)', peripheral connection via RS232 is not working properly. It may due to device problem or connection problem.

Unsigned32

This object specifies a unique number for a peripheral attribute. If no peripheral has more than one attribute, this object will have value '1'.

INTEGER1 = lampOperTime2 = lampState3 = powerSwitchState · Integer32

This object specifies description of a attribute. The supported attributes are lampOperTime(1) -- indicate the lamp operating time of a peripheral lampState(2) -- indicate the lamp state powerSwitchState(3) -- indicate the power on/off state of a peripheral Note that not all peripheral contains all the supported attributes. Agent reports whatever is available.

Unsigned32

This object specifies value of the attribute corresponding to ctpPeripheralAttributeDescr. The possible value of the supported attributes is listed as the following: Attribute Unit SYNTAX ----------------------------------------------------------- lampOperTime hours Unsigned32(0..4294967295) lampState INTEGER { on(1), off(2), failure(3), unknown(4) } powerSwitchState INTEGER { on(1), off(2), unknown(3) }

Unsigned32

This object indicates an arbitrary positive, integer-value that uniquely identifies the USB peripheral.

CtpPeripheralCableCode1 = plugged2 = loose3 = unplugged4 = unknown5 = internalErrorThe textual convention identifies cable status of the attached peripheral through HDMI. plugged (1) -- Peripheral cable is plugged. loose (2) -- Peripheral cable is loose. unplugged (3) -- Peripheral cable is unplugged. unknown (4) -- Cannot detect peripheral cable status. internalError (5) -- Internal error. · Integer32

This object indicates the status of the cable attaching the USB peripheral.

INTEGER1 = unknown2 = self3 = bus4 = both · Integer32

This object indicates the source of power for the attached USB peripheral: 'unknown' - The source of power is unknown. 'self' - The USB peripheral is externally powered. 'bus' - The USB peripheral is powered by the USB bus. 'both' - The USB peripheral can be powered by both the USB bus or self

INTEGER1 = host2 = device3 = hub · Integer32

This object indicates the type of device connected to the USB port: 'host' - no device os connected to the port 'device' - a usb device is connected to the port 'hub' - a usb hub is connected to the port

INTEGER1 = low2 = full3 = high · Integer32

This object indicates the current operational rate of the USB peripheral: 'unknown' - The USB port rate is unknown 'low' - The USB port rate is at 1.5 Mbps. 'full' - The USB port rate is at 12 Mbps. 'high' - The USB port rate is at 480 Mbps.

Unsigned32

This object indicates an arbitrary positive, integer-value that uniquely identifies the IEEE 802.11 peripheral.

InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d

This object indicates an index value that uniquely identifies the interface to which this entry is applicable. If this entry doesn't have corresponding ifIndex, then this value will have value '0'.

InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention. ipv4z(3) A non-global IPv4 address including a zone index as defined by the InetAddressIPv4z textual convention. ipv6z(4) A non-global IPv6 address including a zone index as defined by the InetAddressIPv6z textual convention. dns(16) A DNS domain name as defined by the InetAddressDNS textual convention. Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType. To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32

This object indicates the type of address indicated by the corresponding instance of ctp802dot11PeripheralAddr.

InetAddressDenotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row. The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING

This object indicates the address of the attached peripheral in the format indicated by the corresponding instance of ctp802dot11PeripheralAddrType.

Unsigned32

This object indicates the link strength of an IEEE 802.11 link for a peripheral. A return value of 0 indicates the link is not connected. A return value between 1 - 5 indicates the strength of the link, with 1 being the weakest and 5 being the strongest.

CtpPeripheralCableCode1 = plugged2 = loose3 = unplugged4 = unknown5 = internalErrorThe textual convention identifies cable status of the attached peripheral through HDMI. plugged (1) -- Peripheral cable is plugged. loose (2) -- Peripheral cable is loose. unplugged (3) -- Peripheral cable is unplugged. unknown (4) -- Cannot detect peripheral cable status. internalError (5) -- Internal error. · Integer32

This object indicates the link status of the attached peripheral via IEEE 802.11 link.

Unsigned32

This object indicates a unique number for a peripheral DP. If no peripheral has more than one DP, this object will have value '1'.

CtpPeripheralCableCode1 = plugged2 = loose3 = unplugged4 = unknown5 = internalErrorThe textual convention identifies cable status of the attached peripheral through HDMI. plugged (1) -- Peripheral cable is plugged. loose (2) -- Peripheral cable is loose. unplugged (3) -- Peripheral cable is unplugged. unknown (4) -- Cannot detect peripheral cable status. internalError (5) -- Internal error. · Integer32

This object indicates the cable status of a peripheral which is attached to the system via Display Port interface. This object returns 'loose' if system detects cable is 'unplugged' but power is 'on'.

CtpPeripheralPowerCode1 = on2 = standby3 = off4 = unknown5 = internalErrorThe textual convention identifies power status of the attached peripheral through HDMI. on (1) -- Peripheral power is on. standby (2) -- Peripheral power is in standby mode. off (3) -- Peripheral power is off. unknown (4) -- Cannot detect peripheral power status. internalError (5) -- Internal error. · Integer32

This object indicates the power status of a peripheral which is attached to the system via Display Port interface. This object returns 'unknown' if system detects cable is 'unplugged'.

Unsigned32 (1..4294967295)

A unique non-zero integer value that identifies a CtpPeripheralErrorHistoryEntry in the table. The value of this index starts from '1' and monotonically increases for each peripheral error known to the agent. If the value of this object is '4294967295', the agent will use '1' as the value of the next detected peripheral status change.

Unsigned32

The object specifies the value of ctpPeripheralIndex of a peripheral which is in error state. This object is deprecated in favor of ctpPeripheralErrorDeviceCategory and ctpPeripheralErrorDeviceNumber.

CtpPeripheralStatusCode0 = noError1 = other2 = cableError3 = powerError4 = mgmtSysConfigError5 = systemError6 = deviceError7 = linkError8 = commError9 = detectionDisabledThe textual convention identifies the peripheral status. noError (0) -- Expected peripheral device is functioning through the attached port. other (1) -- None of the listed state. cableError (2) -- Expected peripheral device has cabling issue. powerError (3) -- Expected peripheral device has power issue. mgmtSysConfigError (4) -- Expected peripheral device has communications management system configuration issue. systemError (5) -- Telepresence system error. deviceError (6) -- Expected peripheral device is attached but not fully functional. linkError (7) -- Expected peripheral device has port level link issue. commError (8) -- Expected peripheral device has port level communication issue. detectionDisabled (9) -- Status detection has been disabled. · Integer32

This object specifies the peripheral status after its status changed.

TimeStampThe value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset to zero as a result of a re- initialization of the network management (sub)system, then the values of all TimeStamp objects are also reset. However, after approximately 497 days without a re- initialization, the sysUpTime object will reach 2^^32-1 and then increment around to zero; in this case, existing values of TimeStamp objects do not change. This can lead to ambiguities in the value of TimeStamp objects. · TimeTicks

This object specifies the value of the sysUpTime object at the time the notification was generated.

CtpPeripheralDeviceCategoryCode0 = unknown1 = other2 = uplinkDevice3 = ipPhone4 = camera5 = display6 = secCodec7 = docCamera8 = projector9 = dviDevice10 = presentationCodec11 = auxiliaryControlUnit12 = audioExpansionUnit13 = microphone14 = headset15 = positionMic16 = digitialMediaSystem17 = auxHDMIOutputDevice18 = uiDevice19 = auxHDMIInputDevice20 = bringYourOwnDeviceThe textual convention identifies the peripheral type. unknown (0) -- Unknown Device other (1) -- None of the listed device uplinkDevice (2) -- Device attached to CTS uplink port ipPhone (3) -- IP phone camera (4) -- Camera display (5) -- Display secCodec (6) -- CTS secondary codec docCamera (7) -- Document camera projector (8) -- Projector dviDevice (9) -- Device attached to DVI port presentationCodec (10) -- CTS codec process presentation -- stream auxiliaryControlUnit (11) -- Auxiliary control unit audioExpansionUnit (12) -- Audio expansion unit microphone (13) -- Microphone headset (14) -- Headset positionMic (15) -- Position microphone digitalMediaSystem (16) -- Digitial Media System auxHDMIOuputDevice (17) -- Auxiliary HDMI output device uiDevice (18) -- User Interface device for CTS auxHDMIInputDevice (19) -- HDMI input enabled device bringYourOwnDevice (20) -- Bring Your Own Device, -- like PC,Laptop,Tablet etc · Integer32

The object specifies peripheral device category after its status changed.

Unsigned32

The object specifies peripheral device number after its status changed. Device number is unique within the same peripheral device category.

Unsigned32 (1..4294967295)

A unique non-zero integer value that identifies a CtpSysUserAuthFailHistoryEntry in the table. The value of this index starts from '1' and monotonically increases for each system authentication failure event known to the agent. If the value of this object is '4294967295', the agent will use '1' as the value of the next user authentication failure event.

InetAddressType0 = unknown1 = ipv42 = ipv63 = ipv4z4 = ipv6z16 = dnsA value that represents a type of Internet address. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address that is not in one of the formats defined below. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention. ipv4z(3) A non-global IPv4 address including a zone index as defined by the InetAddressIPv4z textual convention. ipv6z(4) A non-global IPv6 address including a zone index as defined by the InetAddressIPv6z textual convention. dns(16) A DNS domain name as defined by the InetAddressDNS textual convention. Each definition of a concrete InetAddressType value must be accompanied by a definition of a textual convention for use with that InetAddressType. To support future extensions, the InetAddressType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that InetAddressType objects and any dependent objects (e.g., InetAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change an InetAddressType object would, for example, lead to an undefined InetAddress value. In particular, InetAddressType/InetAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)). · Integer32

The object specifies the type of address contained in the corresponding instance of ctpSysUserAuthFailSourceAddr.

InetAddressDenotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value. Every usage of the InetAddress textual convention is required to specify the InetAddressType object that provides the context. It is suggested that the InetAddressType object be logically registered before the object(s) that use the InetAddress textual convention, if they appear in the same logical row. The value of an InetAddress object must always be consistent with the value of the associated InetAddressType object. Attempts to set an InetAddress object to a value inconsistent with the associated InetAddressType must fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. SIZE (0..255) · OCTET STRING

The object specifies the source address when the user authentication failure occurred, in the format given by the corresponding instance of ctpSysUserAuthFailSourceAddrType.

Unsigned32

The object specifies the source TCP/UDP port number when a user authentication failure occurred.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (1..32) · OCTET STRING · hint 255t

The object specifies the user name which was used to gain system access when authentication failure occurred.

CtpSystemAccessProtocol1 = http2 = snmp3 = sshThe textual convention identifies supported Telepresence user access protocol. http (1) -- Hypertext Transfer Protocol (HTTP) snmp (2) -- Simple Network Management Protocol (SNMP) ssh (3) -- Secure Shell (SSH) · Integer32

This object specifies the access protocol when a user authentication failure occurred.

TimeStampThe value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset to zero as a result of a re- initialization of the network management (sub)system, then the values of all TimeStamp objects are also reset. However, after approximately 497 days without a re- initialization, the sysUpTime object will reach 2^^32-1 and then increment around to zero; in this case, existing values of TimeStamp objects do not change. This can lead to ambiguities in the value of TimeStamp objects. · TimeTicks

This object specifies the value of the sysUpTime object at the time the notification was generated.