CISCO-WAN-OPTIMIZATION-MIB

Gauge32 · number of peers

This object contains total number of active peers connected with this device for WAN optimization.

Unsigned32

This object contains maximum number of peers that this device can peer with for WAN optimization.

Unsigned32 (1..100) · percent

This object contains high threshold (percentage) value of CPU usage of system when WAN optimization feature is running. The current CPU utilization, stored in cpmCPUTotalMonIntervalValue, is compared against this value. A cwoCpuThrottlingOn notification is generated whenever cpmCPUTotalMonIntervalValue exceeds cwoGeneralCpuThrottleHigh for cwoGeneralCpuThrottlPeriod.

Unsigned32 (1..100) · percent

This object contains low threshold (percentage) value of CPU usage of system when WAN optimization feature is running. The current CPU utilization, stored in cpmCPUTotalMonIntervalValue, is compared against this value. A cwoCpuThrottlingOff notification is generated if a prior cwoCpuThrottlingOn notification was generated, and the current value of cpmCPUTotalMonIntervalValue is below cwoGeneralCpuThrottleLow for cwoGeneralCpuThrottlPeriod. Note that the value of cwoGeneralCpuThrottleLow must be less than or equal to cwoGeneralCpuThrottleHigh.

TimeIntervalA period of time, measured in units of 0.01 seconds. (0..2147483647) · Integer32

This Object indicates CPU throttling observation period. The value of the CPU utilization for this period is stored in cpmCPUTotalMonIntervalValue. If the value of cpmCPUTotalMonIntervalValue object is above cwoGeneralCPUThrottleHigh, a cwoCPUThrottlingOn notification is sent. If it is below cwoGeneralCPUThrottleLow, a cwoCPUThrottlingOff notification is sent to the NMS.

Counter64 (0..18446744073709551615)

This object contains total number of TCP connections optimized since TFO was started or its statistics were last reset.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64

This object contains number of currently active TCP connections getting optimized.

Unsigned64An unsigned 64 bit integer. We use SYNTAX Counter64 for the encoding rules. (0..18446744073709551615) · Counter64

This object contains maximum number of active TCP connections that this device can optimize.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64

This object contains number of active TCP connections going through TCP plus other optimization.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64

This object contains number of active connections going through only TCP optimization.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64

This object contains number of current active TCP connections that were originated by an accelerator to acquire data in anticipation of its future use.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64

This object contains number of current active TCP connections in the auto-discovery state.

Unsigned64An unsigned 64 bit integer. We use SYNTAX Counter64 for the encoding rules. (0..18446744073709551615) · Counter64

This object contains number of TCP connections reserved for the MAPI accelerator.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64

This object contains number of TCP connections, which are pending in queue of connections to be optimized.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64

This object contains number of active Pass Through TCP connections. Connections which are not selected for optimization are called Pass Through.

Counter64 (0..18446744073709551615)

This object contains total number of optimized TCP connections which were closed normally since TFO was started or its statistics were last reset.

Counter64 (0..18446744073709551615)

This object contains total number of optimized TCP connections, which are reset since TFO was started or its statistics were last reset.

CwoLoadStates1 = unknown2 = green3 = yellow4 = redRepresents load status of the system or feature. unknown : This state is applicable when feature is not active or disabled. green : This state indicates that the feature is operating normally, within acceptable load limits. yellow : This state indicates that the feature is overloaded, and new connections received by it may not get optimized. red : This state indicates that the feature is not healthy, and existing as well as new connections received by it may not get optimized. · Integer32

This object indicates the load status of Traffic Flow Optimizer (TFO).

Counter64 (0..18446744073709551615) · bytes

This object contains total number of bytes read from SMB Application Optimizer cache (Read-ahead and Metadata cache) since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615) · bytes

This object contains total number of bytes written to SMB Application Optimizer cache (Read-ahead and Metadata) since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615) · bytes

This object contains total number of bytes read from file servers by SMB Application Optimizer since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615) · bytes

This object contains total number of bytes written to file servers by SMB Application Optimizer since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615) · bytes

This object contains total number of bytes read by SMB Application Optimizer clients since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615) · bytes

This object contains total number of bytes written by SMB Application optimizer clients since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615) · requests

This object contains total number of requests processed by SMB Application Optimizer since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · requests

This object contains total number of active requests getting processed by SMB Application Optimizer.

Unsigned64An unsigned 64 bit integer. We use SYNTAX Counter64 for the encoding rules. (0..18446744073709551615) · Counter64 · requests

This object contains total number of requests timed out in SMB Application Optimizer since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615) · requests

This object contains total number of SMB requests sent to remote file server since SMB AO was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615) · requests

This object contains total number of SMB requests served locally by SMB Application Optimizer since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32

This object contains average duration of time taken by SMB Application Optimizer to process all remote requests since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32

This object contains average duration of time taken by SMB Application Optimizer to process all local requests since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615)

This object contains SMB Application Optimizer Read Ahead Cache hit count since SMB AO was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615)

This object contains SMB Application Optimizer Metadata cache hit count since SMB AO was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Gauge32 (0..100) · percent

This object contains SMB Application Optimizer Read Ahead cache hit rate since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Gauge32 (0..100) · percent

This object contains SMB Application Optimizer Metadata cache hit rate since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Unsigned64An unsigned 64 bit integer. We use SYNTAX Counter64 for the encoding rules. (0..18446744073709551615) · Counter64 · bytes

This object contains Maximum disk space that can be allocated for Read Ahead data in SMB Application Optimizer cache.

Unsigned64An unsigned 64 bit integer. We use SYNTAX Counter64 for the encoding rules. (0..18446744073709551615) · Counter64 · bytes

This object contains maximum disk space that can be allocated for Metadata in SMB Application Optimizer cache.

CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes

This object contains current size of Metadata cache in SMB Application Optimizer.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32

This object contains amount of time spent in the SMB Application Optimizer Read Ahead cache by the resource that was last evicted since last update. If this amount is too short or too long, it is recommended to modify the size of the cache.

TimeIntervalSecA period of time, measured in units of 1 second. · Unsigned32

This object contains total round trip time for all SMB connections since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

TimeIntervalSecA period of time, measured in units of 1 second. · Unsigned32

This object contains total response time saved due to SMB AO optimizations since it was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Gauge32 · files

This object contains number of files currently opened by SMB Application Optimizer.

Gauge32 · files

This object contains total number of files in SMB Application optimizer Read Ahead cache.

Counter64 (0..18446744073709551615)

This object contains the total number of Layer 4 (L4) optimized signed bytes read from WAN by SMB Application Optimizer since the SMB Application Optimizer was started. L4 optimization comprises of TFO, DRE and LZ optimizations. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615)

This object contains the total number of Layer 4 (L4) optimized signed bytes written to WAN by SMB Application Optimizer since SMB Application Optimizer was started. L4 optimization comprises of TFO, DRE and LZ optimizations. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615)

This object contains the total number of signed bytes read from LAN by SMB Application Optimizer since the SMB Application Optimizer was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

Counter64 (0..18446744073709551615)

This object contains the total number of original signed bytes written to LAN by SMB Application Optimizer since SMB Application Optimizer was started. Discontinuities in the value of this counter can occur at re-initialization of the SMB AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the SMB AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates total time saved due to optimizations done by HTTP AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the HTTP AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the HTTP AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates total Round Trip Time (RTT) for all the connections going through HTTP AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the HTTP AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the HTTP AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates total time for Meta Data Cache Misses (MDCM) for HTTP AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the HTTP AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the HTTP AO.

Gauge32 (0..100) · percent

This object indicates percentage estimated time saved due to optimizations done by HTTP AO since it was started.

Counter64 (0..18446744073709551615) · sessions

This object indicates the total number of SharePoint Optimized HTTP sessions. This counter is incremented for every session on which SharePoint optimization can be performed. An HTTP session is tagged as a SharePoint Session based on the information present in the HTTP request.

Counter64 (0..18446744073709551615) · sessions

This object indicates the total number of SharePoint Pre-fetch optimized HTTP sessions. This counter is incremented for every session on which SharePoint pre-fetch optimization can be performed. An HTTP session is tagged as a SharePoint pre-fetch Session based on the information present in the HTTP request. A pre-fetch operation is one where the edge WAAS device fetches the next set of data (which it anticipates the client will request later) from the server based on the current HTTP Request information.

Counter64 (0..18446744073709551615) · requests

This object indicates the total number of pre-fetched objects served locally for SharePoint pre-fetch sessions. The edge WAAS device maintains a local cache where the pre-fetched responses are saved. This object is incremented whenever the SharePoint client request is served from the pre-fetch cache.

Counter64 (0..18446744073709551615) · milliseconds

This object contains total Round Trip Time (RTT) saved due to SharePoint pre-fetch optimizations since SharePoint pre-fetch optimization was started. Discontinuities in the value of this counter can occur at re-initialization of the HTTP AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the HTTP AO.

Counter64 (0..18446744073709551615) · milliseconds

This object indicates total time for SharePoint pre-fetch Cache Misses since SharePoint pre-fetch optimization was started. Discontinuities in the value of this counter can occur at re-initialization of the HTTP AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the HTTP AO.

Counter64 (0..18446744073709551615) · requests

This object indicates the Akamai connected cache statistics for total number of cache-bypass transactions that were handled in bypass mode transparent cache profile. When bypass mode transparent cache profile is set for a particular hostname, the caching for the hostname specified in a rule is suppressed. In this mode, the cache-engine turns off caching for one or more configured sites.

Counter64 (0..18446744073709551615) · bytes

This object indicates the total number of response bytes saved for cache-hit HTTP transactions in bypass mode transparent cache profile.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of cache-hit HTTP transactions in bypass mode transparent cache profile.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of response bytes saved for cache-hit HTTP transactions in bypass mode transparent cache profile.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the total response time saved for cache-hit HTTP transactions in bypass mode transparent cache profile, in milli-seconds.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the average response time saved per cache-hit HTTP transaction in bypass mode transparent cache profile, in milli-seconds.

Gauge32 (0..100) · percent

This object indicates the percentage of total response time saved for cache-hit HTTP transactions in bypass mode transparent cache profile.

Counter64 (0..18446744073709551615) · requests

This object indicates the Akamai connected cache statistics for total number of cache-hit transactions that were served from cache in standard mode transparent cache profile. This is a default mode.In this mode, the cache engine also follows the RFC-2616 behavior for cache control headers with the exception of not honoring the client cache override behavior.

Counter64 (0..18446744073709551615) · bytes

This object indicates the total number of response bytes saved for cache-hit HTTP transactions in standard mode transparent cache profile.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of cache-hit HTTP transactions in standard mode transparent cache profile.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of response bytes saved for cache-hit HTTP transactions in standard mode transparent cache profile.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the total response time saved for cache-hit HTTP transactions in standard mode transparent cache profile, in milli-seconds.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the average response time saved per cache-hit HTTP transaction in standard mode transparent cache profile, in milli-seconds.

Gauge32 (0..100) · percent

This object indicates the percentage of total response time saved for cache-hit HTTP transactions in standard mode transparent cache profile.

Counter64 (0..18446744073709551615) · requests

This object indicates the Akamai connected cache statistics for total number of cache-hit transactions that were served from cache in basic mode transparent cache profile. In this mode, the cache engine works in strict RFC-2616 behavior, and therefore, only caches responses that are marked explicitly as cacheable with cache-control headers or responses that have an expiry header to service and accelerate traffic from a datacenter to a branch office over any type of IP network.

Counter64 (0..18446744073709551615) · bytes

This object indicates the total number of response bytes saved for cache-hit HTTP transactions in basic mode transparent cache profile.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of cache-hit HTTP transactions in basic mode transparent cache profile.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of response bytes saved for cache-hit HTTP transactions in basic mode transparent cache profile.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the total response time saved for cache-hit HTTP transactions in basic mode transparent cache profile, in milli-seconds.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the average response time saved per cache-hit HTTP transaction in basic mode transparent cache profile, in milli-seconds.

Gauge32 (0..100) · percent

This object indicates the percentage of total response time saved for cache-hit HTTP transactions in basic mode transparent cache profile.

Counter64 (0..18446744073709551615) · requests

This object indicates the Akamai connected cache statistics for total number of cache-hit transactions that were served from cache in advanced mode transparent cache profile. In advanced mode,the cache engine caches media types more aggressively, and caches all object types for longer time (when there is no explicit expiration time).

Counter64 (0..18446744073709551615) · bytes

This object indicates the total number of response bytes saved for cache-hit HTTP transactions in advanced mode transparent cache profile.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of cache-hit HTTP transactions in advanced mode transparent cache profile.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of response bytes saved for cache-hit HTTP transactions in advanced mode transparent cache profile.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the total response time saved for cache-hit HTTP transactions in advanced mode transparent cache profile, in milli-seconds.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the average response time saved per cache-hit HTTP transaction in advanced mode transparent cache profile, in milli-seconds.

Gauge32 (0..100) · percent

This object indicates the percentage of total response time saved for cache-hit HTTP transactions in advanced mode transparent cache profile.

Counter64 (0..18446744073709551615) · requests

This object indicates the aggregation of all the statistics related to various Akamai Connected Cache profile types - Bypass, Standard, Basic and Advanced.

Counter64 (0..18446744073709551615) · bytes

This object indicates the total number of response bytes saved for cache-hit HTTP transactions in all transparent cache profile modes.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of cache-hit HTTP transactions in all transparent cache profile modes.

Gauge32 (0..100) · percent

This object indicates the percentage of total number of response bytes saved for cache-hit HTTP transactions in all transparent cache profile modes.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the total response time saved for cache-hit HTTP transactions in all transparent cache profile modes, in milli-seconds.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the average response time saved per cache-hit HTTP transaction in all transparent cache profile modes, in milli-seconds.

Gauge32 (0..100) · percent

This object indicates the percentage of total response time saved for Cache-hit HTTP transactions in all transparent cache profile modes.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates Average Local Response Time (ALRT) for unencrypted connections of MAPI AO since it was started.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates Average Local Response Time (ALRT) for encrypted connections of MAPI AO since it was started.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates Average Remote Response Time (ARRT) for unencrypted connections of MAPI AO since it was started.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates Average Remote Response Time (ARRT) for encrypted connections of MAPI AO since it was started.

Counter64 (0..18446744073709551615) · requests

This object indicates total requests served locally for unencrypted connections by MAPI AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the MAPI AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the MAPI AO.

Counter64 (0..18446744073709551615) · requests

This object indicates total requests served locally for encrypted connections by MAPI AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the MAPI AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the MAPI AO.

Counter64 (0..18446744073709551615) · requests

This object indicates total Remote Requests(RR) served by remote servers for unencrypted connections of MAPI AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the MAPI AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the MAPI AO.

Counter64 (0..18446744073709551615) · requests

This object indicates total Remote Requests(RR) served by remote servers for encrypted connections by MAPI AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the MAPI AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the MAPI AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates average time reduced for unencrypted connections due to optimizations done by MAPI AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the MAPI AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the MAPI AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates average time reduced for encrypted connections due to optimizations done by MAPI AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the MAPI AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the MAPI AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates Average Local Response Time (ALRT) for NFS AO since it was started.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates Average Remote Response Time (ARRT) for NFS AO since it was started.

Counter64 (0..18446744073709551615) · requests

This object indicates total requests served locally by NFS AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the NFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the NFS AO.

Counter64 (0..18446744073709551615) · requests

This object indicates total Remote Requests (RR) served by remote servers for NFS AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the NFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the NFS AO.

Gauge32 (0..100) · percent

This object indicates percentage estimated time saved due to optimizations done by NFS AO since it was started.

Counter64 (0..18446744073709551615) · bytes

This object indicates total incoming bytes for Video AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the Video AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the Video AO.

Counter64 (0..18446744073709551615) · bytes

This object indicates total outgoing bytes for Video AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the Video AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the Video AO.

Counter32 · kilo-bytes

This object indicates the total bytes read by clients from the client side (via cache or remotely) using CIFS AO since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

Counter32 · kilo-bytes

This object indicates the total bytes written to the client-side using the CIFS AO since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

Counter32 · requests

This object indicates the total requests sent to remote file server since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

Counter32 · requests

This object indicates the total number requests served locally by CIFS AO since it was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the total duration of time taken by CIFS AO to process all remote requests since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object indicates the total duration of time taken by CIFS AO to process all local requests since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

Gauge32 · sessions

This object indicates the number of currently connected CIFS sessions.

Gauge32 · files

This object indicates the number of currently open CIFS files.

Gauge32 · kilo-bytes

This object indicates the maximum disk space (in KB) allocated for data in the CIFS AO cache.

Gauge32 · kilo-bytes

This object indicates the amount of disk space (in KB), currently being used for data in the CIFS AO cache.

Gauge32 · files

This object indicates the maximum number of cache resources (files and directories) supported by the CIFS AO cache, regardless of the size of these resources.

Gauge32 · files

This object indicates the number of cache resources (files and directories) currently held in the CIFS AO cache.

Counter32 · files

This object indicates the number of cache resources (files and directories) that have been evicted from the cache since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

TimeStampThe value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset to zero as a result of a re- initialization of the network management (sub)system, then the values of all TimeStamp objects are also reset. However, after approximately 497 days without a re- initialization, the sysUpTime object will reach 2^^32-1 and then increment around to zero; in this case, existing values of TimeStamp objects do not change. This can lead to ambiguities in the value of TimeStamp objects. · TimeTicks

This object indicates the time when cache resources (files and directories) were last evicted from the CIFS AO cache. 00:00 is displayed if no cache resources have been evicted since CIFS AO was started.

Gauge32 (0..100) · percent

This object indicates the disk usage high watermark in percentage that triggers the eviction of resources from the CIFS AO cache.

Gauge32 (0..100) · percent

This object indicates the target disk usage low watermark percentage to be reached via cache eviction when triggered by cfVolHiWatermark. When this low watermark is reached, cache eviction stops.

Gauge32 (0..100) · percent

This object indicates the target percentage of maximum cache resources (defined by cfMaxCacheResources) that triggers the eviction of resources from the CIFS AO cache.

Gauge32 (0..100) · percent

This object indicates the target percentage of maximum cache resources (defined by cfMaxCacheResources) to be reached via cache eviction when triggered by cfAmntHiWatermark. When this low watermark is reached, cache eviction stops.

TimeIntervalA period of time, measured in units of 0.01 seconds. (0..2147483647) · Integer32

This object indicates the amount of time spent in the CIFS AO cache by the resource that was last evicted. If this amount is too short or too long, it is recommended to modify the size of the cache.

TimeStampThe value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset to zero as a result of a re- initialization of the network management (sub)system, then the values of all TimeStamp objects are also reset. However, after approximately 497 days without a re- initialization, the sysUpTime object will reach 2^^32-1 and then increment around to zero; in this case, existing values of TimeStamp objects do not change. This can lead to ambiguities in the value of TimeStamp objects. · TimeTicks

This object indicates the value of sysUpTime when the resource, which was last evicted from the CIFS AO cache has been last accessed.

Counter64 (0..18446744073709551615) · requests

This object contains total number of FindFirst (FF) requests since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

Counter64 (0..18446744073709551615) · requests

This object contains total number of FindFirst (FF) requests sent to the remote file-server since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object contains the average local response time for FindFirst (FF) requests replied locally since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

CiscoMilliSecondsRepresents time unit value in milliseconds. · Unsigned32 · milliseconds

This object contains the average remote response time for FindFirst (FF) requests replied remotely since CIFS AO was started. Discontinuities in the value of this counter can occur at re-initialization of the CIFS AO. The last discontinuity time is indicated by the value of cwoAoStatsLastResetTime for the CIFS AO.

Gauge32 · files

This object contains the total number of currently allocated Directory Resources in CIFS AO.

CwoDreCacheStatus1 = notUsable2 = initializing3 = usable4 = temporarilyFailed5 = failedRepresents various DRE cache status of an application optimizer. notUsable(1) : This state indicates that DRE cache is currently not usable/accessible (eg.,when DRE partition is not mounted/available). initializing(2) : This state indicates that DRE cache is getting initialized. usable(3) : This state indicates that DRE cache is accessible and in usable condition. tempFailed(4) : This state indicates that DRE cache is temporarily not available due to internal errors. failed(5) : This state indicates that DRE cache initialization failed. · Integer32

This object describes the status of the portion of the disk that is meant for DRE cache.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

This object indicates the age of the oldest data present in the DRE cache. For example, let us say that the portion of the disk space allocated for DRE cache is 1GB and it is full. Now, if new data is written onto this cache, then it would replace the oldest data in the cache in First-In-First-Out (FIFO) order. This object will specify what is the oldest data now present in the cache. It takes the format of <x>d<x>h<x>m, where 'x' is an integer number. For example, 6d20h30m means that the oldest data's age is 6 days, 20 hours and 30 minutes.

Unsigned32 · MB

This object indicates the percentage of available disk space for DRE cache. For example, if the total disk space is 202 GB and let us say that 20% of this disk space is allocated for DRE cache, then this would mean that 40GB (40960 MB) out of the total disk space is allocated for DRE cache.

Gauge32 · percent

This object indicates the percentage of DRE disk space currently used out of the total space allocated for DRE cache. For example, if the disk space allocated for DRE cache is 972798MB and if this object indicates 1%, it means that 9727 MB is used and remaining approximate 963071 MB of disk space is free.

Unsigned32 · MB

This object indicates DRE disk space currently used by data unit. DRE stores the actual data as data units in data block and the metadata (chuck signature) in signature block.

Unsigned32 · MB

This object indicates the amount of data unit replaced in the last one hour in DRE cache. DRE stores the actual data as data units in the cache data block. If new data units have to be stored in the cache, the older data units in the cache are evicted in First-In-First-Out (FIFO) order. This object would also indicate how much new data units have been stored in the DRE cache in the past one hour.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

This object indicates the age of oldest data unit in the data block. DRE stores the actual data as data units in the data block and the metadata (chuck signature) in signature block. If new data unit should be written to the data block when it is full, then the oldest data unit currently present in the data block will be evicted. So this object would indicate the age of the oldest data unit present in the DRE cache. It takes the format of <x>d<x>h<x>m, where 'x' is an integer number. For example, 6d20h30m means that the oldest data's age is 6 days, 20 hours and 30 minutes.

Unsigned32 · MB

This object indicates DRE disk space currently used by sigblock or signature block. DRE stores the actual data as data units in cache data block and the metadata (chuck signature) in signature block.

Unsigned32 · MB

This object indicates the amount of signatures replaced in last one hour in sigblock. DRE stores the metadata (chuck signature) in signature block of DRE cache. If new signatures have to be stored in the cache, the older signatures in the sigblock are evicted in First-In-First-Out (FIFO) order. This object would also indicate how much new signatures have been stored in the DRE cache sigblock in the past one hour.

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0..255) · OCTET STRING · hint 255t

This object indicates the age of oldest signature in the sigblock. DRE stores the actual data as data units in the data block and the metadata (chuck signature) in signature block. If a new signature should be written to the sigblock when it is full, then the oldest signature currently present in the sigblock will be evicted. So this object would indicate the age of the oldest signature present in the DRE cache. It takes the format of <x>d<x>h<x>m, where 'x' is an integer number. For example, 6d20h30m means that the oldest data's age is 6 days, 20 hours and 30 minutes.

Gauge32 (1..100) · percent

This object indicates the total compression ratio provided by all the DRE components - DRE, LZ and PLZ (if applicable), during the encoding process. It is the ratio of the number of bytes entering the DRE module (from LAN side) and the number of bytes exiting the DRE module (from WAN side). This object indicates the value that is calculated since the last time the counter was cleared. The calculation is not based on per-connection or per-peer basis.

Unsigned32 · ms

This object indicates the processing latency that is introduced by DRE/LZ/PLZ processes during the encoding of data that is coming into the DRE module. The encoding process comprises of dividing the input data into chunks and calculating the signature of every chunk. This encoding process would add certain latency. Then the LZ compression would add further latency. This object indicates the value that is calculated since the last time the counter was cleared. The calculation is not based on per-connection or per-peer basis.

Unsigned32 · bytes

This object indicates the average size of all the messages handled by DRE during encoding (i.e., for all the messages received from the LAN side). The message size is an important factor in performance of DRE. This object indicates the value that is calculated since the last time the counter was cleared. The calculation is not based on per-connection or per-peer basis.

Gauge32 (1..100) · percent

This object indicates the total compression ratio provided by all the DRE components - DRE, LZ and PLZ (if applicable), during the decoding process. It is the ratio of the number of bytes entering the DRE module (from WAN side) and the number of bytes exiting the DRE module (from LAN side). This object indicates the value that is calculated since the last time the counter was cleared. The calculation is not based on per-connection or per-peer basis.

Unsigned32 · ms

This object indicates the processing latency that is introduced by DRE/LZ/PLZ processes during the decoding of data that is coming into the DRE module. The LZ decompression (for applicable data) would add certain latency. Then the decoding process that involves a lot of signature look-up for disk IO and data fetch from the data unit for recreation of original data, would add further latency. This object indicates the value that is calculated since the last time the counter was cleared. The calculation is not based on per-connection or per-peer basis.

Unsigned32 · bytes

This object indicates the average size of all the messages handled by DRE during decoding (i.e., for all the messages received from the WAN side). The message size is an important factor in performance of DRE. This object indicates the value that is calculated since the last time the counter was cleared. The calculation is not based on per-connection or per-peer basis.

This notification indicates that the device has reached its limit of number of connections it can optimize. No new connections will be picked-up for optimization, while the device is in this state.

This notification indicates the device has reached its limit of number of peer devices with which it can optimize connections. While the device is in this state, connections from new peer device will not be picked-up for optimization.

This notification indicates that the device has detected that the current CPU utilization (stored in cpmCPUTotalMonIntervalValue) is higher than the cwoGeneralCpuThrottleHigh. As a result the device has entered into a throttling mode due to which connections under optimization may experience slowdown. This notification is generated the moment it occurs after a time lapse of 30 minutes since the previous notification.

This notification indicates that device has detected that the CPU utilization of device (stored in cpmCPUTotalMonIntervalValue) has fallen below the cwoGeneralCpuThrottleLow from cwoGeneralCpuThrottleHigh. As a result the device has come out of the throttling mode and there should not be any negative impact of CPU usage on connection under optimization. This notification is generated the moment it occurs after a time lapse of 30 minutes since the previous notification.

This notification is generated when the license on the system expires after the period for which it was installed.

This notification is generated when a requested revoke ticket is obtained. This ticket could have been requested in order to move the license to a different system.

This notification is generated when the license on the system is cleared.