This table together with the 'cwAtmChanCnfgTable' support provisioning of PVC endpoints and SPVCs on an RPM. This table contains objects that are specific to RPM. This table is an augmentation to the 'cwAtmChanCnfgTable'.
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
The VPI value of a VP or VC connection. The cwaChanVpcFlag serves to distinguish if this is a VP/VC connection
cwaChanVci
Unsigned32 (0..65535)
The VCI value of VC connection. The cwaChanVpcFlag serves to distinguish if this is a VP/VC connection. For a VPC, the VCI is irrelevant and is set to a value of 0
cwrChanSubInterface
1.3.6.1.4.1.351.150.9.1.1.1.1.1
Unsigned32
The RPM's backplane sub-interface for which this channel is configured. Sub-interface 0 means the switch port.
cwrChanVcd
1.3.6.1.4.1.351.150.9.1.1.1.1.2
Unsigned32 (0..4095)
Virtual Circuit Descriptor. A unique number which identifies a connection.
ATM adaptation layer (AAL) and Encapsulation type.
aal5ciscoPPP - For Cisco PPP over ATM.
'cwrChanVirtualTemplate' is required to be set for this type.
aal5muxAPOLLO - For a multiplex (MUX) - type virtual
circuit using the Apollo protocol. aal5muxAPPLETALK - For a MUX-type virtual circuit using the AppleTalk protocol.
aal5muxDECNET - For a MUX-type virtual circuit using the
DECnet protocol.
aal5muxIP - For a MUX-type virtual circuit using the
IP protocol.
aal5muxIPX - For a MUX-type virtual circuit using the
IPX protocol.
aal5muxPPP - For a MUX-type virtual circuit using the
PPP protocol. 'cwrChanVirtualTemplate' is required to be set for this type.
aal5muxVINES - For a MUX-type virtual circuit using the
VINES protocol.
aal5muxXNS - For a MUX-type virtual circuit using the
XNS protocol.
aal5nlpid - Allows ATM interfaces to interoperate with
HSSI.
aal5snap - The only encapsulation supported for
Inverse ARP. Logical Link Control/ Subnetwork Access Protocol (LLC/SNAP) precedes the protocol datagram.
ilmi - Used to set up communication with ILMI.
qsaal - A signalling type PVC used for setting up
or tearing down SVCs.
cwrChanVirtualTemplate
1.3.6.1.4.1.351.150.9.1.1.1.1.4
Unsigned32 (0..200)
This object identifies the virtual template.
The non-zero value need to be specified for Cisco PPP or MUX-type PPP encapsulation (i.e. cwrChanAalEncapType = aal5ciscoPPP or aal5muxPPP).
The value 0 signifies that Virtual Template is not applicable.
cwrChanInArpInterval
1.3.6.1.4.1.351.150.9.1.1.1.1.5
Unsigned32 (0..60) · minutes
This specifies how often Inverse ARP datagrams will be sent on this channel. 0 will disable the InArp for this channel. This object is only supported for aal5snap encapsulation (i.e. cwrChanAalEncapType = aal5snap).
cwrChanOamLoopbkTxInterval
1.3.6.1.4.1.351.150.9.1.1.1.1.6
Unsigned32 (0..600) · seconds
This specifies how often to generate an OAM F5 loopback cell from this channel. 0 will disable generation of OAM F5 loopback cells.
cwrChanOamManage
1.3.6.1.4.1.351.150.9.1.1.1.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This enables/disables OAM management for this channel. If set to true(1), OAM management is enabled.
cwrChanOamRetryUpCount
1.3.6.1.4.1.351.150.9.1.1.1.1.8
Unsigned32 (1..600)
Number of consecutive end-to-end F5 OAM loopback cell responses that must be received in order to change a PVC connection state to up. This object only applies if OAM management is enabled (i.e. cwrChanOAMManage = true).
cwrChanOamRetryDownCount
1.3.6.1.4.1.351.150.9.1.1.1.1.9
Unsigned32 (1..600)
Number of consecutive end-to-end F5 OAM loopback cell responses that are not received in order to change a PVC connection state to down. This object only applies if OAM management is enabled (i.e. cwrChanOAMManage = true).
cwrChanOamRetryInterval
1.3.6.1.4.1.351.150.9.1.1.1.1.10
Unsigned32 (1..1000) · seconds
The frequency that end-to-end F5 OAM loopback cells are transmitted when a change in UP/DOWN state of a PVC is being verified. This object only applies if OAM management is enabled (i.e. cwrChanOAMManage = true).