CISCO-WAN-TRAP-VARS-MIB

Integer32 (0..2147483647)

The object containing the value which can be used for indexing to any table.

Integer32 (1..64)

This object contains the slot number of the module.

AutonomousTypeRepresents an independently extensible type identification value. It may, for example, indicate a particular sub-tree with further MIB definitions, or define a particular type of protocol or hardware. · OBJECT IDENTIFIER

This object contains the entPhysicalVendorType value for the physical entity.

Integer32 (1..4)

This object contains the value for entPhysicalParentRelPos object for line modules.

OCTET STRING SIZE (0..1024)

This object contains the octet string value.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

This object contains the display string value.

INTEGER (0..2147483647) · Integer32

This object contains the container(parent unit number) number of an entity in entPhysicalTable. This object contains the value for the following entities: Fan Tray Power Supply Tray/Group. If it contains value zero, then this object is not applicable for the entity identified by cwTrapPhysicalUnit.

INTEGER (0..2147483647) · Integer32

This object contains the physical unit number(Relative Position) of the physical entity. The physical unit number depends upon the value specified in cwTrapPhysicalContainer object.

INTEGER1 = t12 = e13 = t34 = e3 · Integer32

This object indicates the card role change to T1 from E1, or T3 from E3, vice versa. In case of a card with multiple roles, this object only indicates the changeable role swap between T1 and E1, or T3 and E3.

INTEGER1 = axsm2 = axsme3 = pxm1e4 = hsfr · Integer32

This object is used only for traps and represents the cwSctCardType object in CISCO-WAN-SCT-MGMT-MIB.my.

INTEGER1 = portSct2 = cardSct · Integer32

This object is used only for traps and represents the cwSctType object in CISCO-WAN-SCT-MGMT-MIB.my.

Unsigned32 (1..65535)

This object is used only for traps and represents the cwSctId object in CISCO-WAN-SCT-MGMT-MIB.my.

Unsigned32 (1..65535)

This object is used only for traps and represents the cwSctMajorVersion object in CISCO-WAN-SCT-MGMT-MIB.my.

Unsigned32 (1..1024)

This is an object used only for traps and contains a value for the length of another object. For instance, this can be the length of an address.

INTEGER3 = e1648 = nsap · Integer32

This object is used only for traps and represents the type of an ATM addresses.

Integer32 (1..65535)

This object is used only for traps and represents an object of the same SYNTAX. This object is used in place of: a) 'cwapReference' in CISCO-WAN-ATM-PARTY-MIB.my.

Integer32 (0..2147483647)

The object containing the value which can be used for indexing to any table.

Integer32 (0..2147483647)

The object containing the value which can be used for indexing to any table.