CISCO-WPAN-MIB

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

INTEGER1 = unknown2 = powerDown3 = powerUp4 = moduleRemove5 = moduleReload6 = driverStop7 = driverStart8 = firmwareUpgrade9 = firmwareReset10 = watchDog · Integer32

This object indicates the reason of the last state change of the WPAN service associated with this given interface. unknown (1) - unknown powerDown (2) - power down WPAN module powerUp (3) - power up WPAN module moduleRemove (4) - module removed moduleReload (5) - power cycle WPAN module driverStop (6) - driver stop driverStart (7) - driver start firmwareUpgrade (8) - firmware upgrade firmwareReset (9) - firmware reset watchDog (10) - watchdog triggered

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

INTEGER1 = unknown2 = manuallyClear3 = configChange4 = interfaceDown5 = timeout6 = serviceStop · Integer32

This object indicates the last reset reason of the WPAN RPL table associated with this given interface. unknown (1) - unknown manuallyClear (2) - RPL table was manually cleared configChange (3) - WPAN configuration changed interfaceDown (4) - WPAN interface was down timeout (5) - RPL table has not been updated for a long time serviceStop (6) - WPAN service has stopped

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

Unsigned32

This object indicates the total number of entries in the WPAN RPL table for this given interface.

Unsigned32

This object specifies the threshold for the RPL table nodes. When the value of the corresponding instance of cwpanIfRplTableNodes is greater than this threshold, a cwpanRisingIfRplTblMinorThreshNodesNotif notification will be generated. After a cwpanRisingIfRplTblMinorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes stays above this threshold. When the value of the corresponding instance of cwpanIfRplTableNodes becomes less than or equal to this threshold after a cwpanRisingIfRplTblMinorThreshNodesNotif notification is generated, a cwpanFallingIfRplTblMinorThreshNodesNotif notification will be generated. After a cwpanFallingIfRplTblMinorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes does not exceed this threshold.

Unsigned32

This object specifies the major node threshold for the WPAN RPL table. When the value of the corresponding instance of cwpanIfRplTableNodes is greater than this value, a cwpanRisingIfRplTblMajorThreshNodesNotif notification will be generated. After a cwpanRisingIfRplTblMajorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes stays above this value. When the value of the corresponding instance of cwpanIfRplTableNodes becomes less than or equal to this value after a cwpanRisingIfRplTblMajorThreshNodesNotif notification is generated, a cwpanFallingIfRplTblMajorThreshNodesNotif notification will be generated. After a cwpanFallingIfRplTblMajorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes does not exceed this value.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

Unsigned32

This object indicates the total number of entries in the WPAN RPL table for this given interface.

Unsigned32

This object specifies the threshold for the RPL table nodes. When the value of the corresponding instance of cwpanIfRplTableNodes is greater than this threshold, a cwpanRisingIfRplTblMinorThreshNodesNotif notification will be generated. After a cwpanRisingIfRplTblMinorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes stays above this threshold. When the value of the corresponding instance of cwpanIfRplTableNodes becomes less than or equal to this threshold after a cwpanRisingIfRplTblMinorThreshNodesNotif notification is generated, a cwpanFallingIfRplTblMinorThreshNodesNotif notification will be generated. After a cwpanFallingIfRplTblMinorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes does not exceed this threshold.

Unsigned32

This object specifies the major node threshold for the WPAN RPL table. When the value of the corresponding instance of cwpanIfRplTableNodes is greater than this value, a cwpanRisingIfRplTblMajorThreshNodesNotif notification will be generated. After a cwpanRisingIfRplTblMajorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes stays above this value. When the value of the corresponding instance of cwpanIfRplTableNodes becomes less than or equal to this value after a cwpanRisingIfRplTblMajorThreshNodesNotif notification is generated, a cwpanFallingIfRplTblMajorThreshNodesNotif notification will be generated. After a cwpanFallingIfRplTblMajorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes does not exceed this value.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

Unsigned32

This object indicates the total number of entries in the WPAN RPL table for this given interface.

Unsigned32

This object specifies the major node threshold for the WPAN RPL table. When the value of the corresponding instance of cwpanIfRplTableNodes is greater than this value, a cwpanRisingIfRplTblMajorThreshNodesNotif notification will be generated. After a cwpanRisingIfRplTblMajorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes stays above this value. When the value of the corresponding instance of cwpanIfRplTableNodes becomes less than or equal to this value after a cwpanRisingIfRplTblMajorThreshNodesNotif notification is generated, a cwpanFallingIfRplTblMajorThreshNodesNotif notification will be generated. After a cwpanFallingIfRplTblMajorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes does not exceed this value.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

Unsigned32

This object indicates the total number of entries in the WPAN RPL table for this given interface.

Unsigned32

This object specifies the major node threshold for the WPAN RPL table. When the value of the corresponding instance of cwpanIfRplTableNodes is greater than this value, a cwpanRisingIfRplTblMajorThreshNodesNotif notification will be generated. After a cwpanRisingIfRplTblMajorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes stays above this value. When the value of the corresponding instance of cwpanIfRplTableNodes becomes less than or equal to this value after a cwpanRisingIfRplTblMajorThreshNodesNotif notification is generated, a cwpanFallingIfRplTblMajorThreshNodesNotif notification will be generated. After a cwpanFallingIfRplTblMajorThreshNodesNotif is generated, another such notification will not be generated if the value of the corresponding instance of cwpanIfRplTableNodes does not exceed this value.

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

INTEGER1 = true2 = false · Integer32

This object indicates the standby is ready. 1 - true 2 - false

INTEGER1 = invalid2 = automatic3 = manual · Integer32

This object indicates the WPAN HA state change reason associated with this given interface. 1 - invalid 2 - automatic 3 - manual

INTEGER1 = disabled2 = active3 = standby · Integer32

This object indicates the WPAN HA state associated with this given interface. 1 - disabled 2 - active 3 - standby

DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the ifTable together represent a single interface as named by the device, then each will have the same value of ifName. Note that for an agent which responds to SNMP queries concerning an interface on some other (proxied) device, then the value of ifName for such an interface is the proxied device's local name for it. If there is no local name, or this object is otherwise not applicable, then this object contains a zero-length string.

INTEGER1 = registrationFailed2 = sessionMismatch4 = modeMismatch8 = processEnableFail16 = modeSetFail32 = eui64SetFail64 = eui64GetFail128 = beaconVersionSetFail256 = rplVersionSetFail512 = neighbourSetFail1024 = sockCloseFail2048 = peerConnectionFail4096 = invalidEvent8192 = prefixUpdateFail16384 = standbyNotReady32768 = configMismatch · Integer32

This object indicates the last failure code for the WPAN HA associated with this given interface. registrationFailed(1), sessionMismatch(2), modeMismatch(4), processEnableFail(8), modeSetFail(16), eui64SetFail(32), eui64GetFail(64), beaconVersionSetFail(128), rplVersionSetFail(256), neighbourSetFail(512), sockCloseFail(1024), peerConnectionFail(2048), invalidEvent(4096), prefixUpdateFail(8192), standbyNotReady(16384), configMismatch(32768)