InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
dsx0Ds0ChannelNumber
1.3.6.1.2.1.10.81.1.1.1
INTEGER (0..31) · Integer32
This object indicates the channel number of the ds0 on its DS1/E1.
dsx0RobbedBitSignalling
1.3.6.1.2.1.10.81.1.1.2
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object indicates if Robbed Bit Signalling is turned on or off for a given ds0. This only applies to DS0s on a DS1 link. For E1 links the value is always off (false).
dsx0CircuitIdentifier
1.3.6.1.2.1.10.81.1.1.3
DisplayStringRepresents textual information taken from the NVT ASCII
character set, as defined in pages 4, 10-11 of RFC 854.
To summarize RFC 854, the NVT ASCII repertoire specifies:
- the use of character codes 0-127 (decimal)
- the graphics characters (32-126) are interpreted as US ASCII
- NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854
- the other 25 codes have no standard interpretation
- the sequence 'CR LF' means newline
- the sequence 'CR NUL' means carriage-return
- an 'LF' not preceded by a 'CR' means moving to the same column on the next line.
- the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.)
Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
This object contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.
dsx0IdleCode
1.3.6.1.2.1.10.81.1.1.4
INTEGER (0..15) · Integer32
This object contains the code transmitted in the ABCD bits when the ds0 is not connected and dsx0TransmitCodesEnable is enabled. The object is a bitmap and the various bit positions are:
1 D bit
2 C bit
4 B bit
8 A bit
dsx0SeizedCode
1.3.6.1.2.1.10.81.1.1.5
INTEGER (0..15) · Integer32
This object contains the code transmitted in the ABCD bits when the ds0 is connected and dsx0TransmitCodesEnable is enabled. The object is a bitmap and the various bit positions are:
1 D bit
2 C bit
4 B bit
8 A bit
dsx0ReceivedCode
1.3.6.1.2.1.10.81.1.1.6
INTEGER (0..15) · Integer32
This object contains the code being received in the ABCD bits. The object is a bitmap and the various bit positions are:
1 D bit
2 C bit
4 B bit
8 A bit
dsx0TransmitCodesEnable
1.3.6.1.2.1.10.81.1.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object determines if the idle and seized codes are transmitted. If the value of this object is true then the codes are transmitted.
dsx0Ds0BundleMappedIfIndex
1.3.6.1.2.1.10.81.1.1.8
InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d
This object indicates the ifIndex value assigned by the agent for the ds0Bundle(82) ifEntry to which the given ds0(81) ifEntry may belong.
If the given ds0(81) ifEntry does not belong to any ds0Bundle(82) ifEntry, then this object has a value of zero.
While this object provides information that can also be found in the ifStackTable, it provides this same information with a single table lookup, rather than by walking the ifStackTable to find the possibly non-existent ds0Bundle(82) ifEntry that may be stacked above the given ds0(81) ifTable entry.
dsx0ChanMappingTable
1.3.6.1.2.1.10.81.3
Index: ifIndex · dsx0Ds0ChannelNumber
The DS0 Channel Mapping table. This table maps a DS0 channel number on a particular DS1/E1 into an ifIndex.
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
dsx0ChanMappedIfIndex
1.3.6.1.2.1.10.81.3.1.1
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
This object indicates the ifIndex value assigned by the agent for the individual ds0 ifEntry that corresponds to the given DS0 channel number (specified by the INDEX element dsx0Ds0ChannelNumber) of the given channelized interface (specified by INDEX element ifIndex).