jnxIfOtnNotificationTrigDefaultHoldtimeUp
1.3.6.1.4.1.2636.3.70.1.1.7
Integer32
This object will indicate the time (ms) for the defect to persist before it is declared an alarm.
JUNIPER-IFOTN-MIB
2016-09-12
Deprecated OCh2 tables and entries
Download JUNIPER-IFOTN-MIB.txt Open JUNIPER-IFOTN-MIB.txt in a new tab
SCALARS (5) · TABLES (12) · TRAPS (2)
Scalars (5)
Tables (12)
Traps (2)
| Name | OID |
|---|---|
| jnxIfOtnNotificationAdminStatus | 1.3.6.1.4.1.2636.4.21.0.1 |
| jnxIfOtnNotificationOperStatus | 1.3.6.1.4.1.2636.4.21.0.2 |
END OF TOC
Scalar details
jnxIfOtnNotificationTrigDefaultHoldtimeDown
1.3.6.1.4.1.2636.3.70.1.1.8
Integer32
This object will indicate the time (ms) for the defect to absent before the alarm is cleared.
jnxOtnClearAllPMs
1.3.6.1.4.1.2636.3.70.1.1.10
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
To clear all Performance monitoring counters on OTN interfaces
jnxOtnClearInterfacePMs
1.3.6.1.4.1.2636.3.70.1.1.11
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
To clear all Performance monitoring counters on this OTN interfaces
jnxOtnClearInterfaceCurrentPM
1.3.6.1.4.1.2636.3.70.1.1.12
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
To clear the current Performance monitoring counters on this OTN interfaces
Table details
jnxIfOtnOChCfgTable
1.3.6.1.4.1.2636.3.70.1.1.1
Index: jnxIfOtnOChCfgContainerIndex · jnxIfOtnOChCfgL1Index · jnxIfOtnOChCfgL2Index · jnxIfOtnOChCfgL3Index
Information about the Otn OCh Config Table.
jnxIfOtnOChCfgContainerIndex
1.3.6.1.4.1.2636.3.70.1.1.1.1.1
Integer32 (1..1024)
The associated jnxContentsContainerIndex - eg shelf..
jnxIfOtnOChCfgL1Index
1.3.6.1.4.1.2636.3.70.1.1.1.1.2
Integer32 (1..1024)
The level one index associated with this subject ... eg fpc slot.
jnxIfOtnOChCfgL2Index
1.3.6.1.4.1.2636.3.70.1.1.1.1.3
Integer32 (1..1024)
The level two index associated with this subject .. eg pic slot.
jnxIfOtnOChCfgL3Index
1.3.6.1.4.1.2636.3.70.1.1.1.1.4
Integer32 (1..1024)
The level three index associated with this subject.. eg port.
jnxIfOtnLocalLoopback
1.3.6.1.4.1.2636.3.70.1.1.1.1.5
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This is the local loopback at the Line (after the optics).
jnxIfOtnLineLoopback
1.3.6.1.4.1.2636.3.70.1.1.1.1.6
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This is the line loopback at the Line.
jnxIfOtnPayloadLoopback
1.3.6.1.4.1.2636.3.70.1.1.1.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This is the Payload loopback before the optics.
jnxIfOtnAdminState
1.3.6.1.4.1.2636.3.70.1.1.1.1.8
JnxIfAdminStates1 = jnxAdminStateInService2 = jnxAdminStateInServiceMA3 = jnxAdminStateOutofService4 = jnxAdminStateOutofServiceMAAdmin states for an interface · Integer32
The Admin state of this interface
jnxIfOtnOperState
1.3.6.1.4.1.2636.3.70.1.1.1.1.9
JnxIfOperStates1 = jnxOperStateInit2 = jnxOperStateNormal3 = jnxOperStateFault4 = jnxOperStateDegradedOperational states for an interface · Integer32
The operational state of this interface
jnxIfOtnIndex
1.3.6.1.4.1.2636.3.70.1.1.1.1.10
Unsigned32
The interface ifIndex of this interface
jnxIfOtnOChStatus
1.3.6.1.4.1.2636.3.70.1.1.1.1.11
BITS
The interface status at the OCh layer.
jnxIfOtnOChPortMode
1.3.6.1.4.1.2636.3.70.1.1.1.1.12
Unsigned32
The Port Mode for this interface 0 - default (not applicable) 1 - lan 2 - wan 3 - gfp
jnxIfOtnOTUkCfgTable
1.3.6.1.4.1.2636.3.70.1.1.2
Index: jnxIfOtnOTUkCfgContainerIndex · jnxIfOtnOTUkCfgL1Index · jnxIfOtnOTUkCfgL2Index · jnxIfOtnOTUkCfgL3Index
Information about the Otn OTUk config table.
jnxIfOtnOTUkCfgContainerIndex
1.3.6.1.4.1.2636.3.70.1.1.2.1.1
Integer32 (1..1024)
The associated jnxContentsContainerIndex - eg shelf.
jnxIfOtnOTUkCfgL1Index
1.3.6.1.4.1.2636.3.70.1.1.2.1.2
Integer32 (1..1024)
The level one index associated with this subject ... eg fpc slot.
jnxIfOtnOTUkCfgL2Index
1.3.6.1.4.1.2636.3.70.1.1.2.1.3
Integer32 (1..1024)
The level two index associated with this subject .. eg pic slot.
jnxIfOtnOTUkCfgL3Index
1.3.6.1.4.1.2636.3.70.1.1.2.1.4
Integer32 (1..1024)
The level three index associated with this subject.. eg port.
jnxIfOtnOTUkCfgRate
1.3.6.1.4.1.2636.3.70.1.1.2.1.5
JnxIfOtnRate1 = otu02 = otu13 = otu24 = otu2e5 = otu36 = otu47 = otu1e8 = otu5Rates for an interface · Integer32
This is the rate for the interface and the rates depend on the interface/fru type.
jnxIfOtnOTUkCfgFecMode
1.3.6.1.4.1.2636.3.70.1.1.2.1.6
JnxIfOtnFecType0 = nofec1 = gfec2 = efecI23 = efecI34 = efecI45 = efecI56 = efecI67 = efecI78 = efecI89 = efecI910 = gfecandsdfec11 = sdfec12 = hgfec13 = sdfec15fec modes of an interface · Integer32
This is the Fec type in the OTU frame and the selection depends on the interface/fru type.
jnxIfOtnOTUkEnableAutoFrrByteInsert
1.3.6.1.4.1.2636.3.70.1.1.2.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will enable/disable the automatic insertion of the frr SF/SD byte in the overhead bytes(RES)
jnxIfOtnOTUkEnableBERFrrSupport
1.3.6.1.4.1.2636.3.70.1.1.2.1.8
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will enable/disable the FRR support for BER
jnxIfOtnOTUkPreFecBERThresholdMantissa
1.3.6.1.4.1.2636.3.70.1.1.2.1.9
Integer32
This will set the BER threshold(mantissa), which when crossed will trigger Signal Degrade.
jnxIfOtnOTUkPreFecBERThresholdExponent
1.3.6.1.4.1.2636.3.70.1.1.2.1.10
Integer32
This will set the BER threshold(exponent), which when crossed will trigger Signal Degrade.
jnxIfOtnOTUkPreFecBERThresholdTime
1.3.6.1.4.1.2636.3.70.1.1.2.1.11
Integer32 · ms
The collection times (1ms - 1sec) to calculate the BER.
jnxIfOtnOTUkTIMActEnabled
1.3.6.1.4.1.2636.3.70.1.1.2.1.12
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. The default value of this object is false(2).
jnxIfOtnOTUkTxTTI
1.3.6.1.4.1.2636.3.70.1.1.2.1.13
OCTET STRING SIZE (0..64)
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined
jnxIfOtnOTUkRxTTI
1.3.6.1.4.1.2636.3.70.1.1.2.1.14
OCTET STRING SIZE (64)
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined
jnxIfOtnOTUkExpectedRxSapi
1.3.6.1.4.1.2636.3.70.1.1.2.1.15
OCTET STRING SIZE (0..16)
Expected receive SAPI.
jnxIfOtnOTUkExpectedRxDapi
1.3.6.1.4.1.2636.3.70.1.1.2.1.16
OCTET STRING SIZE (0..16)
Expected receive DAPI.
jnxIfOtnOTUkStatus
1.3.6.1.4.1.2636.3.70.1.1.2.1.17
BITS
The interface status at the OTUk layer.
jnxIfOtnOTUkPreFecBERThresholdClearMantissa
1.3.6.1.4.1.2636.3.70.1.1.2.1.18
Integer32
This will set the BER threshold(mantissa) for clear signal degrade condition, which signal degrade condition will be cleared when Pre-Fec error count is below the clear threshold error count.
jnxIfOtnOTUkPreFecBERThresholdClearExponent
1.3.6.1.4.1.2636.3.70.1.1.2.1.19
Integer32
This will set the BER threshold(exponent) for clear signal degrade condition, which signal degrade condition will be cleared when Pre-Fec error count is below the clear threshold error count.
jnxIfOtnOTUkTxSapiTTIFstByteNul
1.3.6.1.4.1.2636.3.70.1.1.2.1.20
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
jnxIfOtnOTUkTxDapiTTIFstByteNul
1.3.6.1.4.1.2636.3.70.1.1.2.1.21
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
jnxIfOtnOTUkExpectedRxSapiFstByteNul
1.3.6.1.4.1.2636.3.70.1.1.2.1.22
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
jnxIfOtnOTUkExpectedRxDapiFstByteNul
1.3.6.1.4.1.2636.3.70.1.1.2.1.23
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
jnxIfOtnODUkCfgTable
1.3.6.1.4.1.2636.3.70.1.1.3
Index: jnxIfOtnODUkCfgContainerIndex · jnxIfOtnODUkCfgL1Index · jnxIfOtnODUkCfgL2Index · jnxIfOtnODUkCfgL3Index
Information about the Otn ODUk config table.
jnxIfOtnODUkCfgContainerIndex
1.3.6.1.4.1.2636.3.70.1.1.3.1.1
Integer32 (1..1024)
The associated jnxContentsContainerIndex - eg shelf..
jnxIfOtnODUkCfgL1Index
1.3.6.1.4.1.2636.3.70.1.1.3.1.2
Integer32 (1..1024)
The level one index associated with this subject ... eg fpc slot.
jnxIfOtnODUkCfgL2Index
1.3.6.1.4.1.2636.3.70.1.1.3.1.3
Integer32 (1..1024)
The level two index associated with this subject .. eg pic slot.
jnxIfOtnODUkCfgL3Index
1.3.6.1.4.1.2636.3.70.1.1.3.1.4
Integer32 (1..1024)
The level three index associated with this subject.. eg port.
jnxIfOtnODUkAPSPCC0
1.3.6.1.4.1.2636.3.70.1.1.3.1.5
Integer32 (0..255)
Read/Write APS PCC byte 0 for this ODUk only.
jnxIfOtnODUkAPSPCC1
1.3.6.1.4.1.2636.3.70.1.1.3.1.6
Integer32 (0..255)
Read/Write APS PCC byte 1 for this ODUk only.
jnxIfOtnODUkAPSPCC2
1.3.6.1.4.1.2636.3.70.1.1.3.1.7
Integer32 (0..255)
Read/Write APS PCC byte 2 for this ODUk only.
jnxIfOtnODUkAPSPCC3
1.3.6.1.4.1.2636.3.70.1.1.3.1.8
Integer32 (0..255)
Read/Write APS PCC byte 3 for this ODUk only.
jnxIfOtnODUkPayloadType
1.3.6.1.4.1.2636.3.70.1.1.3.1.9
Integer32 (0..255)
Read/Write Payload Type for ODUk only.
jnxIfOtnODUkTIMActEnabled
1.3.6.1.4.1.2636.3.70.1.1.3.1.10
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. The default value of this object is false(2).
jnxIfOtnODUkTxTTI
1.3.6.1.4.1.2636.3.70.1.1.3.1.11
OCTET STRING SIZE (0..64)
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
jnxIfOtnODUkRxTTI
1.3.6.1.4.1.2636.3.70.1.1.3.1.12
OCTET STRING SIZE (64)
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
jnxIfOtnODUkExpectedRxSapi
1.3.6.1.4.1.2636.3.70.1.1.3.1.13
OCTET STRING SIZE (0..16)
Expected receive SAPI for this layer.
jnxIfOtnODUkExpectedRxDapi
1.3.6.1.4.1.2636.3.70.1.1.3.1.14
OCTET STRING SIZE (0..16)
Expected receive DAPI for this layer.
jnxIfOtnODUkStatus
1.3.6.1.4.1.2636.3.70.1.1.3.1.15
BITS
The status at the ODUk layer Only some of these alarms are valid for the TCM layer
jnxIfOtnODUkRxPayloadType
1.3.6.1.4.1.2636.3.70.1.1.3.1.16
Integer32 (0..255)
Receive Payload Type for ODUk only.
jnxIfOtnODUkTxSapiTTIFstByteNul
1.3.6.1.4.1.2636.3.70.1.1.3.1.17
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
jnxIfOtnODUkTxDapiTTIFstByteNul
1.3.6.1.4.1.2636.3.70.1.1.3.1.18
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
jnxIfOtnODUkExpectedRxSapiFstByteNul
1.3.6.1.4.1.2636.3.70.1.1.3.1.19
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
jnxIfOtnODUkExpectedRxDapiFstByteNul
1.3.6.1.4.1.2636.3.70.1.1.3.1.20
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
jnxIfOtnTcmCfgTable
1.3.6.1.4.1.2636.3.70.1.1.4
Index: jnxIfOtnTcmCfgContainerIndex · jnxIfOtnTcmCfgL1Index · jnxIfOtnTcmCfgL2Index · jnxIfOtnTcmCfgL3Index · jnxIfOtnTcmCfgLevel
Information about the Otn TCM config table.
jnxIfOtnTcmCfgContainerIndex
1.3.6.1.4.1.2636.3.70.1.1.4.1.1
Integer32 (1..1024)
The associated jnxContentsContainerIndex - eg shelf.
jnxIfOtnTcmCfgL1Index
1.3.6.1.4.1.2636.3.70.1.1.4.1.2
Integer32 (1..1024)
The level one index associated with this subject ... eg fpc slot.
jnxIfOtnTcmCfgL2Index
1.3.6.1.4.1.2636.3.70.1.1.4.1.3
Integer32 (1..1024)
The level two index associated with this subject .. eg pic slot.
jnxIfOtnTcmCfgL3Index
1.3.6.1.4.1.2636.3.70.1.1.4.1.4
Integer32 (1..1024)
The level three index associated with this subject.. eg port.
jnxIfOtnTcmCfgLevel
1.3.6.1.4.1.2636.3.70.1.1.4.1.5
Integer32 (1..6)
The TCM level for the Table
jnxIfOtnTCMEnable
1.3.6.1.4.1.2636.3.70.1.1.4.1.6
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Enable this TCM layer (only for TCM layers)
jnxIfOtnTcmTxTTI
1.3.6.1.4.1.2636.3.70.1.1.4.1.7
OCTET STRING SIZE (0..64)
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
jnxIfOtnTcmRxTTI
1.3.6.1.4.1.2636.3.70.1.1.4.1.8
OCTET STRING SIZE (64)
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
jnxIfOtnTcmExpectedRxSapi
1.3.6.1.4.1.2636.3.70.1.1.4.1.9
OCTET STRING SIZE (0..16)
Expected receive SAPI for this layer.
jnxIfOtnTcmExpectedRxDapi
1.3.6.1.4.1.2636.3.70.1.1.4.1.10
OCTET STRING SIZE (0..16)
Expected receive DAPI for this layer.
jnxIfOtnTcmStatus
1.3.6.1.4.1.2636.3.70.1.1.4.1.11
BITS
The status at the TCM layer.
jnxIfOtnODUkTcmTestTable
1.3.6.1.4.1.2636.3.70.1.1.5
Index: ifIndex · jnxIfOtnODUkTcmTestLayer · jnxIfOtnODUkTcmTestTCMLevel
Information about the Otn ODUk Test function table.
from IF-MIB
ifIndex
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
jnxIfOtnODUkTcmTestLayer
1.3.6.1.4.1.2636.3.70.1.1.5.1.1
JnxIfOtnLayer1 = jnxOch2 = jnxOTUk3 = jnxODUk4 = jnxTCMLayer which describes the table · Integer32
The layer OTU/ODU/TCM layer for the alarm
jnxIfOtnODUkTcmTestTCMLevel
1.3.6.1.4.1.2636.3.70.1.1.5.1.2
Integer32 (0..6)
For ODUk will be this will be 0 If layer is TCM then this will give the TCM level 1..6.
jnxIfOtnODUkTcmInsertAis
1.3.6.1.4.1.2636.3.70.1.1.5.1.3
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Insert ODU Ais into OTN stream.
jnxIfOtnODUkTcmInsertLck
1.3.6.1.4.1.2636.3.70.1.1.5.1.4
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Insert ODU Lck into OTN stream.
jnxIfOtnODUkTcmInsertOci
1.3.6.1.4.1.2636.3.70.1.1.5.1.5
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Insert ODU Oci into OTN stream.
jnxIfOtnODUkPayloadPRBS
1.3.6.1.4.1.2636.3.70.1.1.5.1.6
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Insert Payload PRBS, For ODUK layer and TCM level is 0.
jnxIfOtnODUkPayloadPRBSResult
1.3.6.1.4.1.2636.3.70.1.1.5.1.7
OCTET STRING
Result of the Payload PRBS .
jnxIfOtnODUkTcmDMTable
1.3.6.1.4.1.2636.3.70.1.1.6
Index: ifIndex · jnxIfOtnODUkTcmDMLayer · jnxIfOtnODUkTcmDMLevel
Table for Otn ODUk/TCM Delay Measurement config table.
from IF-MIB
ifIndex
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
jnxIfOtnODUkTcmDMLayer
1.3.6.1.4.1.2636.3.70.1.1.6.1.1
JnxIfOtnLayer1 = jnxOch2 = jnxOTUk3 = jnxODUk4 = jnxTCMLayer which describes the table · Integer32
The layer OTU/ODU/TCM layer for the alarm
jnxIfOtnODUkTcmDMLevel
1.3.6.1.4.1.2636.3.70.1.1.6.1.2
Integer32 (0..6)
For ODUk will be this will be 0 If layer is TCM then this will give the TCM level 1..6.
jnxIfOtnDMConnectionMonitoringEndpoint
1.3.6.1.4.1.2636.3.70.1.1.6.1.3
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Originate Connection Monitoring Endpoint for the Delay Measurement
jnxIfOtnDMBypass
1.3.6.1.4.1.2636.3.70.1.1.6.1.4
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Act as tandem, passing Dm value through node
jnxIfOtnDMPersistFrames
1.3.6.1.4.1.2636.3.70.1.1.6.1.5
Integer32
Number of consequtive frames required to declare Dm Complete
jnxIfOtnDMEnable
1.3.6.1.4.1.2636.3.70.1.1.6.1.6
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Start/Stop the DM measurement
jnxIfOtnDMRemoteLoopEnable
1.3.6.1.4.1.2636.3.70.1.1.6.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Remote Loop Enable/Disable
jnxIfOtnNotificationTrigTable
1.3.6.1.4.1.2636.3.70.1.1.9
Index: jnxIfOtnNotificationTrigContainerIndex · jnxIfOtnNotificationTrigL1Index · jnxIfOtnNotificationTrigL2Index · jnxIfOtnNotificationTrigL3Index · jnxIfOtnNotificationTrigLayer · jnxIfOtnNotificationTrigTCMLevel · jnxIfOtnNotificationTrigAlmId
Information about the otn Alarm/Alart/Info trigger table.
jnxIfOtnNotificationTrigContainerIndex
1.3.6.1.4.1.2636.3.70.1.1.9.1.1
Integer32 (1..1024)
The associated jnxContentsContainerIndex - eg shelf.
jnxIfOtnNotificationTrigL1Index
1.3.6.1.4.1.2636.3.70.1.1.9.1.2
Integer32 (1..1024)
The level one index associated with this subject ... eg fpc slot.
jnxIfOtnNotificationTrigL2Index
1.3.6.1.4.1.2636.3.70.1.1.9.1.3
Integer32 (1..1024)
The level two index associated with this subject .. eg pic slot.
jnxIfOtnNotificationTrigL3Index
1.3.6.1.4.1.2636.3.70.1.1.9.1.4
Integer32 (1..1024)
The level three index associated with this subject.. eg port.
jnxIfOtnNotificationTrigLayer
1.3.6.1.4.1.2636.3.70.1.1.9.1.5
JnxIfOtnLayer1 = jnxOch2 = jnxOTUk3 = jnxODUk4 = jnxTCMLayer which describes the table · Integer32
The layer OTU/ODU/TCM layer for the alarm
jnxIfOtnNotificationTrigTCMLevel
1.3.6.1.4.1.2636.3.70.1.1.9.1.6
Integer32 (0..6)
For OCh/OTUk/ODUk will be this will be 0 If layer is TCM then this will give the TCM level 1..6.
jnxIfOtnNotificationTrigAlmId
1.3.6.1.4.1.2636.3.70.1.1.9.1.7
Integer32 (0..255)
This will be the ID of Alarm for that layer 'JnxoptIfOTNOChAlarms'/'JnxoptIfOTNODUkTcmAlarms'.
jnxIfOtnNotificationTrigSeverity
1.3.6.1.4.1.2636.3.70.1.1.9.1.8
JnxIfOtnSeverity1 = jnxCritical2 = jnxMajor3 = jnxMinor4 = jnxInfoSeverity of the Notification · Integer32
This will be the Severity of the Notification for that layer.
jnxIfOtnNotificationTrigIgnore
1.3.6.1.4.1.2636.3.70.1.1.9.1.9
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This object will ignore the alarm when set.
jnxIfOtnNotificationTrigHoldtimeUp
1.3.6.1.4.1.2636.3.70.1.1.9.1.10
Integer32
This object will indicate the time (ms) for the defect to persist before it is declared an alarm.
jnxIfOtnNotificationTrigHoldtimeDown
1.3.6.1.4.1.2636.3.70.1.1.9.1.11
Integer32
This object will indicate the time (ms) for the defect is absent before the alarm is cleared.
jnxIfOtnTrigServiceStateAction
1.3.6.1.4.1.2636.3.70.1.1.9.1.12
JnxIfOtnServiceStateAction0 = jnxNotSupported1 = jnxNonServiceAffecting2 = jnxServiceAffectingNotification's action on the service state · Integer32
This will indicate whether this alarm is service affecting or not .
jnxOtnClearIfPMsTable
1.3.6.1.4.1.2636.3.70.1.1.13
Index: ifIndex
To clear OTN Performance monitoring counters on this OTN interfaces
from IF-MIB
ifIndex
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
jnxOtnClearCurrent
1.3.6.1.4.1.2636.3.70.1.1.13.1.1
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
1- to clear all the current OTN PM's for this interface
jnxOtnClearInterfaceInterval
1.3.6.1.4.1.2636.3.70.1.1.13.1.2
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
1- to clear all the OTN PM's intervals(1-96) for this interface
jnxOtnClearInterfaceDay
1.3.6.1.4.1.2636.3.70.1.1.13.1.3
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
1 - to clear all the Current Day and Previous Day OTN PM's for this interface
jnxOtnClearInterfaceAll
1.3.6.1.4.1.2636.3.70.1.1.13.1.4
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
1 - to clear all the OTN PM's for this interface
jnxIfOtnOCh2CfgTable
1.3.6.1.4.1.2636.3.70.1.2.1
Index: jnxIfOtnOCh2CfgContainerIndex · jnxIfOtnOCh2CfgL1Index · jnxIfOtnOCh2CfgL2Index · jnxIfOtnOCh2CfgL3Index · jnxIfOtnOCh2CfgL4Index
Table was for 48x10G/12x40G gingerALE PIC in 10G mode. It is not supported hence marked as obsolete. Information about the Otn OCh2 Config Table.
jnxIfOtnOCh2CfgContainerIndex
1.3.6.1.4.1.2636.3.70.1.2.1.1.1
Integer32 (1..1024)
Container Index associated with the object instance.
jnxIfOtnOCh2CfgL1Index
1.3.6.1.4.1.2636.3.70.1.2.1.1.2
Integer32 (1..1024)
FPC slot number of the interface.
jnxIfOtnOCh2CfgL2Index
1.3.6.1.4.1.2636.3.70.1.2.1.1.3
Integer32 (1..1024)
PIC slot number of the interface.
jnxIfOtnOCh2CfgL3Index
1.3.6.1.4.1.2636.3.70.1.2.1.1.4
Integer32 (1..1024)
Port number of the interface.
jnxIfOtnOCh2CfgL4Index
1.3.6.1.4.1.2636.3.70.1.2.1.1.5
Integer32 (1..1024)
Sub-Port number of the interface.
jnxIfOtnOCh2LocalLoopback
1.3.6.1.4.1.2636.3.70.1.2.1.1.6
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This is the local loopback at the Line (after the optics).
jnxIfOtnOCh2LineLoopback
1.3.6.1.4.1.2636.3.70.1.2.1.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This is the line loopback at the Line.
jnxIfOtnOCh2PayloadLoopback
1.3.6.1.4.1.2636.3.70.1.2.1.1.8
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This is the Payload loopback before the optics.
jnxIfOtnOCh2AdminState
1.3.6.1.4.1.2636.3.70.1.2.1.1.9
JnxIfAdminStates1 = jnxAdminStateInService2 = jnxAdminStateInServiceMA3 = jnxAdminStateOutofService4 = jnxAdminStateOutofServiceMAAdmin states for an interface · Integer32
The Admin state of this interface
jnxIfOtnOCh2OperState
1.3.6.1.4.1.2636.3.70.1.2.1.1.10
JnxIfOperStates1 = jnxOperStateInit2 = jnxOperStateNormal3 = jnxOperStateFault4 = jnxOperStateDegradedOperational states for an interface · Integer32
The operational state of this interface
jnxIfOtnOCh2Index
1.3.6.1.4.1.2636.3.70.1.2.1.1.11
Unsigned32
The interface ifIndex of this interface
jnxIfOtnOCh2Status
1.3.6.1.4.1.2636.3.70.1.2.1.1.12
BITS
The interface status at the OCh layer.
jnxIfOtnOCh2PortMode
1.3.6.1.4.1.2636.3.70.1.2.1.1.13
Unsigned32
The Port Mode for this interface 0 - default (not applicable) 1 - lan 2 - wan 3 - gfp
jnxIfOtnOCh2OTUkCfgTable
1.3.6.1.4.1.2636.3.70.1.2.2
Index: jnxIfOtnOCh2OTUkCfgContIndx · jnxIfOtnOCh2OTUkCfgL1Index · jnxIfOtnOCh2OTUkCfgL2Index · jnxIfOtnOCh2OTUkCfgL3Index · jnxIfOtnOCh2OTUkCfgL4Index
Table was for 48x10G/12x40G gingerALE PIC in 10G mode. It is not supported hence marked as obsolete. Information about the Otn OCh2 OTUk config table.
jnxIfOtnOCh2OTUkCfgContIndx
1.3.6.1.4.1.2636.3.70.1.2.2.1.1
Integer32 (1..1024)
Container Index associated with the object instance.
jnxIfOtnOCh2OTUkCfgL1Index
1.3.6.1.4.1.2636.3.70.1.2.2.1.2
Integer32 (1..1024)
FPC slot number of the interface.
jnxIfOtnOCh2OTUkCfgL2Index
1.3.6.1.4.1.2636.3.70.1.2.2.1.3
Integer32 (1..1024)
PIC slot number of the interface.
jnxIfOtnOCh2OTUkCfgL3Index
1.3.6.1.4.1.2636.3.70.1.2.2.1.4
Integer32 (1..1024)
Port number of the interface.
jnxIfOtnOCh2OTUkCfgL4Index
1.3.6.1.4.1.2636.3.70.1.2.2.1.5
Integer32 (1..1024)
Port number of the interface.
jnxIfOtnOCh2OTUkCfgRate
1.3.6.1.4.1.2636.3.70.1.2.2.1.6
JnxIfOtnRate1 = otu02 = otu13 = otu24 = otu2e5 = otu36 = otu47 = otu1e8 = otu5Rates for an interface · Integer32
This is the rate for the interface and the rates depend on the interface/fru type.
jnxIfOtnOCh2OTUkCfgFecMode
1.3.6.1.4.1.2636.3.70.1.2.2.1.7
JnxIfOtnFecType0 = nofec1 = gfec2 = efecI23 = efecI34 = efecI45 = efecI56 = efecI67 = efecI78 = efecI89 = efecI910 = gfecandsdfec11 = sdfec12 = hgfec13 = sdfec15fec modes of an interface · Integer32
This is the Fec type in the OTU frame and the selection depends on the interface/fru type.
jnxIfOtnOCh2OTUkEnAutoFrrByteIns
1.3.6.1.4.1.2636.3.70.1.2.2.1.8
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will enable/disable the automatic insertion of the frr SF/SD byte in the overhead bytes(RES)
jnxIfOtnOCh2OTUkEnBERFrrSupport
1.3.6.1.4.1.2636.3.70.1.2.2.1.9
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
This will enable/disable the FRR support for BER
jnxIfOtnOCh2OTUkPreFecBERThMant
1.3.6.1.4.1.2636.3.70.1.2.2.1.10
Integer32
This will set the BER threshold(mantissa), which when crossed will trigger Signal Degrade.
jnxIfOtnOCh2OTUkPreFecBERThExpo
1.3.6.1.4.1.2636.3.70.1.2.2.1.11
Integer32
This will set the BER threshold(exponent), which when crossed will trigger Signal Degrade.
jnxIfOtnOCh2OTUkPreFecBERThTime
1.3.6.1.4.1.2636.3.70.1.2.2.1.12
Integer32 · ms
The collection times (1ms - 1sec) to calculate the BER.
jnxIfOtnOCh2OTUkTIMActEnabled
1.3.6.1.4.1.2636.3.70.1.2.2.1.13
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. The default value of this object is false(2).
jnxIfOtnOCh2OTUkTxTTI
1.3.6.1.4.1.2636.3.70.1.2.2.1.14
OCTET STRING SIZE (0..64)
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined
jnxIfOtnOCh2OTUkRxTTI
1.3.6.1.4.1.2636.3.70.1.2.2.1.15
OCTET STRING SIZE (64)
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined
jnxIfOtnOCh2OTUkExpectedRxSapi
1.3.6.1.4.1.2636.3.70.1.2.2.1.16
OCTET STRING SIZE (0..16)
Expected receive SAPI.
jnxIfOtnOCh2OTUkExpectedRxDapi
1.3.6.1.4.1.2636.3.70.1.2.2.1.17
OCTET STRING SIZE (0..16)
Expected receive DAPI.
jnxIfOtnOCh2OTUkStatus
1.3.6.1.4.1.2636.3.70.1.2.2.1.18
BITS
The interface status at the OTUk layer.
jnxIfOtnOCh2OTUkPreFecBERThClrMn
1.3.6.1.4.1.2636.3.70.1.2.2.1.19
Integer32
This will set the BER threshold(mantissa) for clear signal degrade condition, which signal degrade condition will be cleared when Pre-Fec error count is below the clear threshold error count.
jnxIfOtnOCh2OTUkPreFecBERThClrEx
1.3.6.1.4.1.2636.3.70.1.2.2.1.20
Integer32
This will set the BER threshold(exponent) for clear signal degrade condition, which signal degrade condition will be cleared when Pre-Fec error count is below the clear threshold error count.
jnxIfOtnOCh2ODUkCfgTable
1.3.6.1.4.1.2636.3.70.1.2.3
Index: jnxIfOtnOCh2ODUkCfgContIndx · jnxIfOtnOCh2ODUkCfgL1Index · jnxIfOtnOCh2ODUkCfgL2Index · jnxIfOtnOCh2ODUkCfgL3Index · jnxIfOtnOCh2ODUkCfgL4Index
Table was for 48x10G/12x40G gingerALE PIC in 10G mode. It is not supported hence marked as obsolete. Information about the Otn ODUk config table.
jnxIfOtnOCh2ODUkCfgContIndx
1.3.6.1.4.1.2636.3.70.1.2.3.1.1
Integer32 (0..255)
Container Index associated with the Object Instance.
jnxIfOtnOCh2ODUkCfgL1Index
1.3.6.1.4.1.2636.3.70.1.2.3.1.2
Integer32 (0..255)
FPC slot number of the interface.
jnxIfOtnOCh2ODUkCfgL2Index
1.3.6.1.4.1.2636.3.70.1.2.3.1.3
Integer32 (0..255)
PIC slot number of the interface.
jnxIfOtnOCh2ODUkCfgL3Index
1.3.6.1.4.1.2636.3.70.1.2.3.1.4
Integer32 (0..255)
Port number of the interface.
jnxIfOtnOCh2ODUkCfgL4Index
1.3.6.1.4.1.2636.3.70.1.2.3.1.5
Integer32 (0..255)
Sub-Port number of the interface.
jnxIfOtnOCh2ODUkAPSPCC0
1.3.6.1.4.1.2636.3.70.1.2.3.1.6
Integer32 (0..255)
Read/Write APS PCC byte 0 for this ODUk only.
jnxIfOtnOCh2ODUkAPSPCC1
1.3.6.1.4.1.2636.3.70.1.2.3.1.7
Integer32 (0..255)
Read/Write APS PCC byte 1 for this ODUk only.
jnxIfOtnOCh2ODUkAPSPCC2
1.3.6.1.4.1.2636.3.70.1.2.3.1.8
Integer32 (0..255)
Read/Write APS PCC byte 2 for this ODUk only.
jnxIfOtnOCh2ODUkAPSPCC3
1.3.6.1.4.1.2636.3.70.1.2.3.1.9
Integer32 (0..255)
Read/Write APS PCC byte 3 for this ODUk only.
jnxIfOtnOCh2ODUkPayloadType
1.3.6.1.4.1.2636.3.70.1.2.3.1.10
Integer32 (0..255)
Read/Write Payload Type for ODUk only.
jnxIfOtnOCh2ODUkTIMActEnabled
1.3.6.1.4.1.2636.3.70.1.2.3.1.11
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. The default value of this object is false(2).
jnxIfOtnOCh2ODUkTxTTI
1.3.6.1.4.1.2636.3.70.1.2.3.1.12
OCTET STRING SIZE (0..64)
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
jnxIfOtnOCh2ODUkRxTTI
1.3.6.1.4.1.2636.3.70.1.2.3.1.13
OCTET STRING SIZE (64)
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
jnxIfOtnOCh2ODUkExpectedRxSapi
1.3.6.1.4.1.2636.3.70.1.2.3.1.14
OCTET STRING SIZE (0..16)
Expected receive SAPI for this layer.
jnxIfOtnOCh2ODUkExpectedRxDapi
1.3.6.1.4.1.2636.3.70.1.2.3.1.15
OCTET STRING SIZE (0..16)
Expected receive DAPI for this layer.
jnxIfOtnOCh2ODUkStatus
1.3.6.1.4.1.2636.3.70.1.2.3.1.16
BITS
The status at the ODUk layer Only some of these alarms are valid for the TCM layer
jnxIfOtnOCh2ODUkRxPayloadType
1.3.6.1.4.1.2636.3.70.1.2.3.1.17
Integer32 (0..255)
Receive Payload Type for ODUk only.
jnxIfOtnOCh2TcmCfgTable
1.3.6.1.4.1.2636.3.70.1.2.4
Index: jnxIfOtnOCh2TcmCfgContIndx · jnxIfOtnOCh2TcmCfgL1Index · jnxIfOtnOCh2TcmCfgL2Index · jnxIfOtnOCh2TcmCfgL3Index · jnxIfOtnOCh2TcmCfgL4Index · jnxIfOtnOCh2TcmCfgLevel
Table was for 48x10G/12x40G gingerALE PIC in 10G mode. It is not supported hence marked as obsolete. Information about the Otn TCM config table.
jnxIfOtnOCh2TcmCfgContIndx
1.3.6.1.4.1.2636.3.70.1.2.4.1.1
Integer32 (0..255)
Container Index associated with the object.
jnxIfOtnOCh2TcmCfgL1Index
1.3.6.1.4.1.2636.3.70.1.2.4.1.2
Integer32 (0..255)
FPC slot number of the interface.
jnxIfOtnOCh2TcmCfgL2Index
1.3.6.1.4.1.2636.3.70.1.2.4.1.3
Integer32 (0..255)
PIC slot number of the interface.
jnxIfOtnOCh2TcmCfgL3Index
1.3.6.1.4.1.2636.3.70.1.2.4.1.4
Integer32 (0..255)
Port number of the interface.
jnxIfOtnOCh2TcmCfgL4Index
1.3.6.1.4.1.2636.3.70.1.2.4.1.5
Integer32 (0..255)
Sub-Port number of the interface.
jnxIfOtnOCh2TcmCfgLevel
1.3.6.1.4.1.2636.3.70.1.2.4.1.6
Integer32 (1..6)
The TCM level for the Table
jnxIfOtnOCh2TCMEnable
1.3.6.1.4.1.2636.3.70.1.2.4.1.7
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
Enable this TCM layer (only for TCM layers)
jnxIfOtnOCh2TcmTxTTI
1.3.6.1.4.1.2636.3.70.1.2.4.1.8
OCTET STRING SIZE (0..64)
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
jnxIfOtnOCh2TcmRxTTI
1.3.6.1.4.1.2636.3.70.1.2.4.1.9
OCTET STRING SIZE (64)
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
jnxIfOtnOCh2TcmExpectedRxSapi
1.3.6.1.4.1.2636.3.70.1.2.4.1.10
OCTET STRING SIZE (0..16)
Expected receive SAPI for this layer.
jnxIfOtnOCh2TcmExpectedRxDapi
1.3.6.1.4.1.2636.3.70.1.2.4.1.11
OCTET STRING SIZE (0..16)
Expected receive DAPI for this layer.
jnxIfOtnOCh2TcmStatus
1.3.6.1.4.1.2636.3.70.1.2.4.1.12
BITS
The status at the TCM layer.
Trap details
jnxIfOtnNotificationAdminStatus
1.3.6.1.4.1.2636.4.21.0.1
Notification of the admin state of the otn interface.
ifDescr
1.3.6.1.2.1.2.2.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
jnxIfOtnAdminState
1.3.6.1.4.1.2636.3.70.1.1.1.1.8
JnxIfAdminStates1 = jnxAdminStateInService2 = jnxAdminStateInServiceMA3 = jnxAdminStateOutofService4 = jnxAdminStateOutofServiceMAAdmin states for an interface · Integer32
The Admin state of this interface
jnxIfOtnNotificationOperStatus
1.3.6.1.4.1.2636.4.21.0.2
Notification of operational state of the otn interface
ifDescr
1.3.6.1.2.1.2.2.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
jnxIfOtnOperState
1.3.6.1.4.1.2636.3.70.1.1.1.1.9
JnxIfOperStates1 = jnxOperStateInit2 = jnxOperStateNormal3 = jnxOperStateFault4 = jnxOperStateDegradedOperational states for an interface · Integer32
The operational state of this interface