2016-09-23
This mib module is for Juniper Networks Proprietory Layer 2 control protocol (L2CP) features
Download JUNIPER-L2CP-FEATURES-MIB.txt Open JUNIPER-L2CP-FEATURES-MIB.txt in a new tab
SCALARS (6) · TABLES (4) · TRAPS (4)
END OF TOC
1.3.6.1.4.1.2636.3.53.1.1.2.2
INTEGER · Integer32
Returns the value of time (in seconds) after which a port on which BPDU error was detected will be re-enabled. A returned value of 0 indicates that port will not be re-enabled automatically.
1.3.6.1.4.1.2636.3.53.1.1.3.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
Lacp member interface.
1.3.6.1.4.1.2636.3.53.1.1.3.2
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
Snmp ifIndex of member interface.
1.3.6.1.4.1.2636.3.53.1.1.3.3
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
Lacp Aggregate interface.
1.3.6.1.4.1.2636.3.53.1.1.3.4
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
Snmp ifIndex of Aggregator.
1.3.6.1.4.1.2636.3.53.1.1.3.5
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
Port actor operational state.
1.3.6.1.4.1.2636.3.53.1.1.1.1
augments dot1dStpPortTable (BRIDGE-MIB)
Index: dot1dStpPort
Defines the jnxDot1dStp Port Table for providing enterprise specific extensions for Root Protect and Loop Protect to the corresponding dot1dStpPortTable entry.
from BRIDGE-MIB
Integer32 (1..65535)
Reference: IEEE 802.1D-1998: clause 14.8.2.1.2
The port number of the port for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.2636.3.53.1.1.1.1.1.1
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
A Boolean value set by management indicating whether Root protect functionality is enabled on the port. If TRUE causes the Port not to be selected as Root Port, even it has the best spanning tree priority vector. This parameter should be FALSE by default.
1.3.6.1.4.1.2636.3.53.1.1.1.1.1.2
INTEGER0 = no-error1 = root-prevented · Integer32
Indicates whether the port was prevented from being a root port. This parameter will always return 'no-error (0)' if jnxDot1dStpPortRootProtectEnabled is FALSE.
1.3.6.1.4.1.2636.3.53.1.1.1.1.1.3
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
A Boolean value set by management indicating whether Loop protect functionality is enabled on the port. If TRUE causes the Port not to be selected as Designated Port when the received superior BPDU is aged out. This parameter should be FALSE by default.
1.3.6.1.4.1.2636.3.53.1.1.1.1.1.4
INTEGER0 = no-error1 = loop-prevented · Integer32
Indicates whether a potential Loop was prevented on the port This parameter will always return 'no-error (0)' if jnxDot1dStpPortLoopProtectEnabled is FALSE.
1.3.6.1.4.1.2636.3.53.1.1.2.1
Index: ifIndex
Defines a Port Table for BPDU Protect information. This contains only those ports on which BPDU Protect can be configured.
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.2636.3.53.1.1.2.1.1.1
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
A Boolean value set by management indicating whether BPDU protect functionality is enabled on the port. If TRUE causes the Port to be disabled (link down) upon receipt of a BPDU. This parameter should be FALSE by default.
1.3.6.1.4.1.2636.3.53.1.1.2.1.1.2
INTEGER0 = no-error1 = detected · Integer32
Indicates whether a BPDU was received on the port. This parameter will always return 'no-error (0)' if jnxL2cpBpduProtectPortEnabled is FALSE.
1.3.6.1.4.1.2636.3.53.1.1.4.1
Index: ifIndex
Reference: IEEE 802.3
A table that contains Link Aggregation Timeout information about a port that is associated with this device. A row appears in this table for each physical port.
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.2636.3.53.1.1.4.1.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
Reference: IEEE 802.3
Physical port that is associated with Aggregation Port. This value is read-only.
1.3.6.1.4.1.2636.3.53.1.1.4.1.1.2
LacpStateThe Actor and Partner State values from the LACPDU. · BITS
Reference: IEEE 802.3 Subclause 30.7.2.1.21
A string of 8 bits, corresponding to the current operational values of Actor_State as transmitted by the Actor in LACPDUs. The bit allocations are as defined in 30.7.2.1.20. This attribute value is read-only.
1.3.6.1.4.1.2636.3.53.1.1.4.1.1.3
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
Reference: IEEE 802.3
Aggregation Port where Physical port is associated with. This value is read-only.
1.3.6.1.4.1.2636.3.53.1.1.4.1.1.4
TimeTicks
Reference: IEEE 802.3
This object represents the time elapsed in seconds since lacp experienced timeout. This value is read-only.
1.3.6.1.4.1.2636.3.53.1.1.5.1
Index: ifIndex
Defines a Port Table for Loop Detect information. This contains only those ports on which Loop Detect is configured.
from IF-MIB
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.2636.3.53.1.1.5.1.1.1
TruthValue1 = true2 = falseRepresents a boolean value. · Integer32
A Boolean value set by management indicating whether Loop Detect functionality is enabled on the port. If TRUE causes the Port to be disabled (link down) upon receipt of a Loop Detect PDU. This parameter should be FALSE by default.
1.3.6.1.4.1.2636.3.53.1.1.5.1.1.2
INTEGER0 = no-error1 = detected · Integer32
Indicates whether a Loop Detect PDU was received on the port. This parameter will always return 'no-error (0)' if jnxL2cpLoopDetectPortEnabled is FALSE.
1.3.6.1.4.1.2636.3.53.1.2.0.1
Generated when the ports Root-protect state (no-error or root-prevented) changes.
1.3.6.1.4.1.2636.3.53.1.1.1.1.1.2
INTEGER0 = no-error1 = root-prevented · Integer32
Indicates whether the port was prevented from being a root port. This parameter will always return 'no-error (0)' if jnxDot1dStpPortRootProtectEnabled is FALSE.
1.3.6.1.4.1.2636.3.53.1.2.0.2
Generated when the ports Loop-protect state (no-error or loop-prevented) changes.
1.3.6.1.4.1.2636.3.53.1.1.1.1.1.4
INTEGER0 = no-error1 = loop-prevented · Integer32
Indicates whether a potential Loop was prevented on the port This parameter will always return 'no-error (0)' if jnxDot1dStpPortLoopProtectEnabled is FALSE.
1.3.6.1.4.1.2636.3.53.1.2.0.3
Generated when the ports BPDU error state (no-error or detected) changes.
1.3.6.1.4.1.2636.3.53.1.1.2.1.1.2
INTEGER0 = no-error1 = detected · Integer32
Indicates whether a BPDU was received on the port. This parameter will always return 'no-error (0)' if jnxL2cpBpduProtectPortEnabled is FALSE.
1.3.6.1.4.1.2636.3.53.1.2.1.1
Lacp times out
1.3.6.1.4.1.2636.3.53.1.1.3.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
Lacp member interface.
1.3.6.1.4.1.2636.3.53.1.1.3.2
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
Snmp ifIndex of member interface.
1.3.6.1.4.1.2636.3.53.1.1.3.3
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
Lacp Aggregate interface.
1.3.6.1.4.1.2636.3.53.1.1.3.4
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
Snmp ifIndex of Aggregator.
1.3.6.1.4.1.2636.3.53.1.1.3.5
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
Port actor operational state.