jnxSpSvcSetFlowLimitUtil
1.3.6.1.4.1.2636.3.32.2.1
Integer32 (0..100)
The Total no of flows present in this Service Set, expressed as a percentage of the total maximum flows.
JUNIPER-SP-MIB
2019-09-19
Provides data about each of the AS Pics on a router.
Download JUNIPER-SP-MIB.txt Open JUNIPER-SP-MIB.txt in a new tab
SCALARS (6) · TABLES (3) · TRAPS (7)
Scalars (6)
Tables (3)
| Name | OID |
|---|---|
| jnxSpSvcSetTable | 1.3.6.1.4.1.2636.3.32.1.1 |
| jnxSpSvcSetSvcTypeTable | 1.3.6.1.4.1.2636.3.32.1.2 |
| jnxSpSvcSetIfTable | 1.3.6.1.4.1.2636.3.32.1.3 |
Traps (7)
END OF TOC
Scalar details
jnxSpSvcSetNameUtil
1.3.6.1.4.1.2636.3.32.2.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..96) · OCTET STRING · hint 255a
The Service Set name.
jnxSpTcpLoggingHostIpaddr
1.3.6.1.4.1.2636.3.32.3.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..64) · OCTET STRING · hint 255a
The TCP logging remote host server IP address.
jnxSpTcpLoggingHostPort
1.3.6.1.4.1.2636.3.32.3.2
Integer32 (0..65535)
The TCP logging remote host server port number.
jnxSpTcpLoggingHostConnStatus
1.3.6.1.4.1.2636.3.32.3.3
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..64) · OCTET STRING · hint 255a
The TCP logging remote host server connection status. Status can be either <connection established> or <connection dropped>
jnxSpTcpLoggingHostRoutingInstance
1.3.6.1.4.1.2636.3.32.3.4
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..64) · OCTET STRING · hint 255a
The routing instance name under which TCP logging remote host server is configured.
Table details
jnxSpSvcSetTable
1.3.6.1.4.1.2636.3.32.1.1
Index: jnxSpSvcSetName
Data about each service set on each Service PIC on the router.
jnxSpSvcSetName
1.3.6.1.4.1.2636.3.32.1.1.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..96) · OCTET STRING · hint 255a
The Service Set name.
jnxSpSvcSetSvcType
1.3.6.1.4.1.2636.3.32.1.1.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The name of the Service Type associated with this table entry.
jnxSpSvcSetTypeIndex
1.3.6.1.4.1.2636.3.32.1.1.1.3
Integer32 (0..255)
A generic integer used to identify the Service Type for this entry.
jnxSpSvcSetIfName
1.3.6.1.4.1.2636.3.32.1.1.1.4
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The ifName of the interface identifying the Service PIC. If more than one interface is associated with the Service PIC, the name associated with the lowest layer interface is used for this object.
jnxSpSvcSetIfIndex
1.3.6.1.4.1.2636.3.32.1.1.1.5
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
The ifIndex corresponding to jnxSpSvcSetIfName.
jnxSpSvcSetMemoryUsage
1.3.6.1.4.1.2636.3.32.1.1.1.6
Gauge32 · bytes
The amount of memory used by this Service Set, expressed in bytes.
jnxSpSvcSetCpuUtil
1.3.6.1.4.1.2636.3.32.1.1.1.7
Gauge32 · percent
The amount of CPU used by this Service Set, expressed as a percentage of the total.
jnxSpSvcSetSvcStyle
1.3.6.1.4.1.2636.3.32.1.1.1.8
INTEGER1 = unknown2 = interface-service3 = next-hop-service · Integer32
The type of this Service Set. The definitions of each style being: Unknown - Service style is not known. Interface-service - Service style is interface based. Next-hop-service - Service style is next-hop based.
jnxSpSvcSetMemLimitPktDrops
1.3.6.1.4.1.2636.3.32.1.1.1.9
Counter32
The number of packets dropped due to the Service Set exceeding its memory limits (when in Red Zone).
jnxSpSvcSetCpuLimitPktDrops
1.3.6.1.4.1.2636.3.32.1.1.1.10
Counter32
The number of packets dropped due to the Service Set exceeding the average cpu limits (when total exceeds 85%).
jnxSpSvcSetFlowLimitPktDrops
1.3.6.1.4.1.2636.3.32.1.1.1.11
Counter32
The number of packets dropped due to the Service Set exceeding the flow limit.
jnxSpSvcSetMemoryUsage64
1.3.6.1.4.1.2636.3.32.1.1.1.12
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes
The amount of memory used by this Service Set, expressed in bytes, represented by 64 bit integer.
jnxSpSvcSetMemLimitPktDrops64
1.3.6.1.4.1.2636.3.32.1.1.1.13
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64
The number of packets dropped due to the Service Set exceeding its memory limits (when in Red Zone), represented by 64 bit integer.
jnxSpSvcSetCpuLimitPktDrops64
1.3.6.1.4.1.2636.3.32.1.1.1.14
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64
The number of packets dropped due to the Service Set exceeding the average cpu limits (when total exceeds 85%), represented by 64 bit integer.
jnxSpSvcSetFlowLimitPktDrops64
1.3.6.1.4.1.2636.3.32.1.1.1.15
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64
The number of packets dropped due to the Service Set exceeding the flow limit, represented by 64 bit integer.
jnxSpSvcSetSessCount
1.3.6.1.4.1.2636.3.32.1.1.1.16
Counter32
The total number of sessions active in the Service Set.
jnxSpSvcSetSessCurrentCount
1.3.6.1.4.1.2636.3.32.1.1.1.17
Gauge32
The total number of sessions active in the Service Set.
jnxSpSvcSetSvcTypeTable
1.3.6.1.4.1.2636.3.32.1.2
Index: ifIndex · jnxSpSvcSetSvcTypeIndex
Data about each service on each Service PIC on the router.
from IF-MIB
ifIndex
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
jnxSpSvcSetSvcTypeIndex
1.3.6.1.4.1.2636.3.32.1.2.1.1
Integer32 (0..255)
A generic integer used to identify the Service Type for this entry.
jnxSpSvcSetSvcTypeIfName
1.3.6.1.4.1.2636.3.32.1.2.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The ifName of the interface identifying the Service PIC. If more than one interface is associated with the Service PIC, the name associated with the lowest layer interface is used for this object.
jnxSpSvcSetSvcTypeName
1.3.6.1.4.1.2636.3.32.1.2.1.3
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The name of the Service Type associated with this table entry.
jnxSpSvcSetSvcTypeSvcSets
1.3.6.1.4.1.2636.3.32.1.2.1.4
Gauge32
The number of Service Sets configured on this Service PIC that use this service type.
jnxSpSvcSetSvcTypeMemoryUsage
1.3.6.1.4.1.2636.3.32.1.2.1.5
Gauge32 · bytes
The amount of memory used by this Service Type, expressed in bytes.
jnxSpSvcSetSvcTypePctMemoryUsage
1.3.6.1.4.1.2636.3.32.1.2.1.6
Gauge32 · percent
The amount of memory used by this Service Type, expressed as a percentage of the total.
jnxSpSvcSetSvcTypeCpuUtil
1.3.6.1.4.1.2636.3.32.1.2.1.7
Gauge32 · percent
The amount of CPU used by this Service Type, expressed as a percentage of the total.
jnxSpSvcSetSvcTypeMemoryUsage64
1.3.6.1.4.1.2636.3.32.1.2.1.8
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes
The amount of memory used by this Service Type, expressed in bytes, represented by 64 bit integer.
jnxSpSvcSetIfTable
1.3.6.1.4.1.2636.3.32.1.3
Index: ifIndex
Service Set data about each Service PIC on the router.
from IF-MIB
ifIndex
InterfaceIndexA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. (1..2147483647) · Integer32 · hint d
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
jnxSpSvcSetIfTableName
1.3.6.1.4.1.2636.3.32.1.3.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The ifName of the interface identifying the Service PIC. If more than one interface is associated with the Service PIC, the name associated with the lowest layer interface is used for this object.
jnxSpSvcSetIfSvcSets
1.3.6.1.4.1.2636.3.32.1.3.1.2
Gauge32
The number of Service Sets configured on this Service PIC.
jnxSpSvcSetIfMemoryUsage
1.3.6.1.4.1.2636.3.32.1.3.1.3
Gauge32 · bytes
The amount of memory used by this Service PIC, expressed in bytes.
jnxSpSvcSetIfPctMemoryUsage
1.3.6.1.4.1.2636.3.32.1.3.1.4
Gauge32 · percent
The amount of memory used by this Service PIC, expressed as a percentage of the total.
jnxSpSvcSetIfPolMemoryUsage
1.3.6.1.4.1.2636.3.32.1.3.1.5
Gauge32 · bytes
The amount of policy memory used by this Service PIC, expressed in bytes.
jnxSpSvcSetIfPctPolMemoryUsage
1.3.6.1.4.1.2636.3.32.1.3.1.6
Gauge32 · percent
The amount of policy memory used by this Service PIC, expressed as a percentage of the total.
jnxSpSvcSetIfMemoryZone
1.3.6.1.4.1.2636.3.32.1.3.1.7
INTEGER1 = green2 = yellow3 = orange4 = red · Integer32
The memory-usage zone currently occupied by this Service PIC. The definitions of each zone are: Green - All new flows are allowed. Yellow - Unused memory is reclaimed. All new flows are allowed. Orange - New flows are only allowed for service sets that are using less than their equal share of memory. Red - No new flows are allowed.
jnxSpSvcSetIfCpuUtil
1.3.6.1.4.1.2636.3.32.1.3.1.8
Gauge32 · percent
The amount of CPU used by this Service PIC, expressed as a percentage of the total.
jnxSpSvcSetIfMemoryUsage64
1.3.6.1.4.1.2636.3.32.1.3.1.9
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes
The amount of memory used by this Service PIC, expressed in bytes, represented by 64 bit integer.
jnxSpSvcSetIfPolMemoryUsage64
1.3.6.1.4.1.2636.3.32.1.3.1.10
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64 · bytes
The amount of policy memory used by this Service PIC, expressed in bytes, represented by 64 bit integer.
jnxSpSvcSetIfNumTotalSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.11
Integer32
The total number of sessions active in the Service PIC.
jnxSpSvcSetIfPeakTotalSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.12
Integer32
The Peak number of sessions active in the Service PIC.
jnxSpSvcSetIfNumCreatedSessPerSec
1.3.6.1.4.1.2636.3.32.1.3.1.13
Integer32
The number of sessions created per second in the Service PIC.
jnxSpSvcSetIfNumDeletedSessPerSec
1.3.6.1.4.1.2636.3.32.1.3.1.14
Integer32
The number of sessions deleted per second in the Service PIC.
jnxSpSvcSetIfNumTotalTcpSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.15
Integer32
The total number of TCP sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalUdpSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.16
Integer32
The total number of UDP sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalOtherSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.17
Integer32
The total number of other (not TCP or UDP) sessions active in the Service PIC.
jnxSpSvcSetIfPeakTotalTcpSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.18
Integer32
The peak number of TCP sessions active in the Service PIC.
jnxSpSvcSetIfPeakTotalUdpSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.19
Integer32
The peak number of UDP sessions active in the Service PIC.
jnxSpSvcSetIfPeakTotalOtherSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.20
Integer32
The peak number of other (not TCP or UDP) sessions active in the Service PIC.
jnxSpSvcSetIfPeakCreatedSessPerSec
1.3.6.1.4.1.2636.3.32.1.3.1.21
Integer32
The peak number of sessions created per second in the Service PIC.
jnxSpSvcSetIfPeakDeletedSessPerSec
1.3.6.1.4.1.2636.3.32.1.3.1.22
Integer32
The peak number of sessions deleted per second in the Service PIC.
jnxSpSvcSetIfNumTotalTcpIpv4SessActive
1.3.6.1.4.1.2636.3.32.1.3.1.23
Integer32
The total number of IPv4 TCP sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalTcpIpv6SessActive
1.3.6.1.4.1.2636.3.32.1.3.1.24
Integer32
The total number of IPv6 TCP sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalUdpIpv4SessActive
1.3.6.1.4.1.2636.3.32.1.3.1.25
Integer32
The total number of IPv4 UDP sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalUdpIpv6SessActive
1.3.6.1.4.1.2636.3.32.1.3.1.26
Integer32
The total number of IPv6 UDP sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalOtherIpv4SessActive
1.3.6.1.4.1.2636.3.32.1.3.1.27
Integer32
The total number of other IPv4 sessions (not TCP or UDP) active in the Service PIC.
jnxSpSvcSetIfNumTotalOtherIpv6SessActive
1.3.6.1.4.1.2636.3.32.1.3.1.28
Integer32
The total number of other IPv6 sessions (not TCP or UDP) active in the Service PIC.
jnxSpSvcSetIfNumTotalTcpGatedSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.29
Integer32
The total number of TCP gated sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalUdpGatedSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.30
Integer32
The total number of UDP gated sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalTcpRegSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.31
Integer32
The total number of TCP regular sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalUdpRegSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.32
Integer32
The total number of UDP regular sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalTcpTunSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.33
Integer32
The total number of TCP tunneled sessions active in the Service PIC.
jnxSpSvcSetIfNumTotalUdpTunSessActive
1.3.6.1.4.1.2636.3.32.1.3.1.34
Integer32
The total number of UDP tunneled sessions active in the Service PIC.
jnxSpSvcSetIfSessPktRecv
1.3.6.1.4.1.2636.3.32.1.3.1.35
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64
The total number of session packets received in the Service PIC.
jnxSpSvcSetIfSessPktXmit
1.3.6.1.4.1.2636.3.32.1.3.1.36
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64
The total number of session packets transmitted in the Service PIC.
jnxSpSvcSetIfSessSlowPathDiscard
1.3.6.1.4.1.2636.3.32.1.3.1.37
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64
The total number of session packets discarded in the slow path in the Service PIC.
jnxSpSvcSetIfSessSlowPathForward
1.3.6.1.4.1.2636.3.32.1.3.1.38
CounterBasedGauge64The CounterBasedGauge64 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^64-1 (18446744073709551615 decimal), and the minimum value can not be smaller than 0. The value of a CounterBasedGauge64 has its maximum value whenever the information being modeled is greater than or equal to its maximum value, and has its minimum value whenever the information being modeled is smaller than or equal to its minimum value. If the information being modeled subsequently decreases below (increases above) the maximum (minimum) value, the CounterBasedGauge64 also decreases (increases). Note that this TC is not strictly supported in SMIv2, because the 'always increasing' and 'counter wrap' semantics associated with the Counter64 base type are not preserved. It is possible that management applications which rely solely upon the (Counter64) ASN.1 tag to determine object semantics will mistakenly operate upon objects of this type as they would for Counter64 objects. This textual convention represents a limited and short-term solution, and may be deprecated as a long term solution is defined and deployed to replace it. (0..18446744073709551615) · Counter64
The total number of session packets forwarded in the slow path in the Service PIC.
jnxSpSvcSetIfMspNumCreatedSubsPerSec
1.3.6.1.4.1.2636.3.32.1.3.1.39
Integer32
The total number of subscribers created per second in the Service PIC.
jnxSpSvcSetIfMspNumDeletedSubsPerSec
1.3.6.1.4.1.2636.3.32.1.3.1.40
Integer32
The total number of subscribers deleted per second in the Service PIC.
jnxSpSvcSetIfMspNumTotalSubsActive
1.3.6.1.4.1.2636.3.32.1.3.1.41
Integer32
The total number of subscribers active in the Service PIC.
jnxSpSvcSetIfMspPeakCreatedSubsPerSec
1.3.6.1.4.1.2636.3.32.1.3.1.42
Integer32
The peak number of subscribers created per second in the Service PIC.
jnxSpSvcSetIfMspPeakDeletedSubsPerSec
1.3.6.1.4.1.2636.3.32.1.3.1.43
Integer32
The peak number of subscribers deleted per second in the Service PIC.
jnxSpSvcSetIfMspPeakTotalSubsActive
1.3.6.1.4.1.2636.3.32.1.3.1.44
Integer32
The peak total number of subscribers active in the Service PIC.
Trap details
jnxSpSvcSetZoneEntered
1.3.6.1.4.1.2636.4.10.0.1
This indicates a Service PIC has entered a more severe memory-usage zone from a less severe memory usage zone. The zone entered is identified by jnxSpSvcSetIfMemoryZone.
jnxSpSvcSetIfMemoryZone
1.3.6.1.4.1.2636.3.32.1.3.1.7
INTEGER1 = green2 = yellow3 = orange4 = red · Integer32
The memory-usage zone currently occupied by this Service PIC. The definitions of each zone are: Green - All new flows are allowed. Yellow - Unused memory is reclaimed. All new flows are allowed. Orange - New flows are only allowed for service sets that are using less than their equal share of memory. Red - No new flows are allowed.
jnxSpSvcSetIfTableName
1.3.6.1.4.1.2636.3.32.1.3.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The ifName of the interface identifying the Service PIC. If more than one interface is associated with the Service PIC, the name associated with the lowest layer interface is used for this object.
jnxSpSvcSetZoneExited
1.3.6.1.4.1.2636.4.10.0.2
This indicates a Service Pic has exited a more severe memory-usage zone to a less severe memory usage zone. The zone exited is identified by jnxSpSvcSetIfMemoryZone.
jnxSpSvcSetIfMemoryZone
1.3.6.1.4.1.2636.3.32.1.3.1.7
INTEGER1 = green2 = yellow3 = orange4 = red · Integer32
The memory-usage zone currently occupied by this Service PIC. The definitions of each zone are: Green - All new flows are allowed. Yellow - Unused memory is reclaimed. All new flows are allowed. Orange - New flows are only allowed for service sets that are using less than their equal share of memory. Red - No new flows are allowed.
jnxSpSvcSetIfTableName
1.3.6.1.4.1.2636.3.32.1.3.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The ifName of the interface identifying the Service PIC. If more than one interface is associated with the Service PIC, the name associated with the lowest layer interface is used for this object.
jnxSpSvcSetCpuExceeded
1.3.6.1.4.1.2636.4.10.0.3
This indicates a Service Pic has exceeded its internal threshold for CPU utilization (85%).
jnxSpSvcSetIfCpuUtil
1.3.6.1.4.1.2636.3.32.1.3.1.8
Gauge32 · percent
The amount of CPU used by this Service PIC, expressed as a percentage of the total.
jnxSpSvcSetIfTableName
1.3.6.1.4.1.2636.3.32.1.3.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The ifName of the interface identifying the Service PIC. If more than one interface is associated with the Service PIC, the name associated with the lowest layer interface is used for this object.
jnxSpSvcSetCpuOk
1.3.6.1.4.1.2636.4.10.0.4
This indicates a Service Pic has crossed below its internal threshold for CPU utilization (85%).
jnxSpSvcSetIfCpuUtil
1.3.6.1.4.1.2636.3.32.1.3.1.8
Gauge32 · percent
The amount of CPU used by this Service PIC, expressed as a percentage of the total.
jnxSpSvcSetIfTableName
1.3.6.1.4.1.2636.3.32.1.3.1.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..255) · OCTET STRING · hint 255a
The ifName of the interface identifying the Service PIC. If more than one interface is associated with the Service PIC, the name associated with the lowest layer interface is used for this object.
jnxSpSvcSetFlowLimitUtilised
1.3.6.1.4.1.2636.4.10.0.5
This indicates a Service Set has reached its upper limit of flows threshold of a maximun flows allowed for a service set.
jnxSpSvcSetFlowLimitUtil
1.3.6.1.4.1.2636.3.32.2.1
Integer32 (0..100)
The Total no of flows present in this Service Set, expressed as a percentage of the total maximum flows.
jnxSpSvcSetNameUtil
1.3.6.1.4.1.2636.3.32.2.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..96) · OCTET STRING · hint 255a
The Service Set name.
jnxSpTcpLoggingHostStatus
1.3.6.1.4.1.2636.4.10.0.6
This provides TCP logging host connection status for Service Set.
jnxSpTcpLoggingHostIpaddr
1.3.6.1.4.1.2636.3.32.3.1
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..64) · OCTET STRING · hint 255a
The TCP logging remote host server IP address.
jnxSpTcpLoggingHostPort
1.3.6.1.4.1.2636.3.32.3.2
Integer32 (0..65535)
The TCP logging remote host server port number.
jnxSpTcpLoggingHostConnStatus
1.3.6.1.4.1.2636.3.32.3.3
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..64) · OCTET STRING · hint 255a
The TCP logging remote host server connection status. Status can be either <connection established> or <connection dropped>
jnxSpTcpLoggingHostRoutingInstance
1.3.6.1.4.1.2636.3.32.3.4
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..64) · OCTET STRING · hint 255a
The routing instance name under which TCP logging remote host server is configured.
jnxSpSvcSetFlowLimitUtilized
1.3.6.1.4.1.2636.4.10.1
This indicates a Service Set has reached its upper limit of flows threshold of a maximun flows allowed for a service set.
jnxSpSvcSetFlowLimitUtil
1.3.6.1.4.1.2636.3.32.2.1
Integer32 (0..100)
The Total no of flows present in this Service Set, expressed as a percentage of the total maximum flows.
jnxSpSvcSetNameUtil
1.3.6.1.4.1.2636.3.32.2.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (1..96) · OCTET STRING · hint 255a
The Service Set name.