2015-02-09
Download POWER-ATTRIBUTES-MIB.txt Open POWER-ATTRIBUTES-MIB.txt in a new tab
Copyright (c) 2015 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This MIB is used to report AC power attributes in devices. The table is a sparse augmentation of the eoPowerTable table from the energyObjectMib module. Both three-phase and single-phase power configurations are supported. As a requirement for this MIB module, RFC 7461 SHOULD be implemented. Module Compliance of ENTITY-MIB v4 with respect to entity4CRCompliance MUST be supported which requires implementation of four MIB objects: entPhysicalIndex, entPhysicalClass, entPhysicalName, and entPhysicalUUID.
| Name | OID |
|---|---|
| eoACPwrAttributesTable | 1.3.6.1.2.1.230.1.1 |
| eoACPwrAttributesDelPhaseTable | 1.3.6.1.2.1.230.1.2 |
| eoACPwrAttributesWyePhaseTable | 1.3.6.1.2.1.230.1.3 |
END OF TOC
1.3.6.1.2.1.230.1.1
Index: entPhysicalIndex
This table contains power attributes measurements for supported entPhysicalIndex entities. It is a sparse extension of the eoPowerTable.
from ENTITY-MIB
PhysicalIndexAn arbitrary value that uniquely identifies the physical entity. The value should be a small positive integer. Index values for different physical entities are not necessarily contiguous. (1..2147483647) · Integer32 · hint d
The index for this entry.
1.3.6.1.2.1.230.1.1.1.1
INTEGER1 = sngl2 = del3 = wye · Integer32
Configuration describes the physical configurations of the power supply lines: * alternating current, single phase (SNGL) * alternating current, three-phase delta (DEL) * alternating current, three-phase Y (WYE) Three-phase configurations can be either connected in a triangular delta (DEL) or star Y (WYE) system. WYE systems have a shared neutral voltage, while DEL systems do not. Each phase is offset 120 degrees to each other.
1.3.6.1.2.1.230.1.1.1.2
Integer32 · 0.1 Volt AC
A measured value for average of the voltage measured over an integral number of AC cycles. For a three-phase system, this is the average voltage (V1+V2+V3)/3. IEC 61850-7-4 measured value attribute 'Vol'.
1.3.6.1.2.1.230.1.1.1.3
Unsigned32 · amperes
A measured value for average of the current measured over an integral number of AC cycles. For a three-phase system, this is the average current (I1+I2+I3)/3. IEC 61850-7-4 attribute 'Amp'.
1.3.6.1.2.1.230.1.1.1.4
Integer32 (4500..6500) · 0.01 hertz
A measured value for the basic frequency of the AC circuit. IEC 61850-7-4 attribute 'Hz'.
1.3.6.1.2.1.230.1.1.1.5
UnitMultiplier-24 = yocto-21 = zepto-18 = atto-15 = femto-12 = pico-9 = nano-6 = micro-3 = milli0 = units3 = kilo6 = mega9 = giga12 = tera15 = peta18 = exa21 = zetta24 = yottaThe Unit Multiplier is an integer value that represents the IEEE 61850 Annex A units multiplier associated with the integer units used to measure the power or energy. For example, when used with eoPowerUnitMultiplier, -3 represents 10^-3 or milliwatts.Reference: The International System of Units (SI), National Institute of Standards and Technology, Spec. Publ. 330, August 1991. · Integer32
The magnitude of watts for the usage value in eoACPwrAttributesTotalActivePower, eoACPwrAttributesTotalReactivePower, and eoACPwrAttributesTotalApparentPower measurements. For three-phase power systems, this will also include eoACPwrAttributesWyeActivePower, eoACPwrAttributesWyeReactivePower, and eoACPwrAttributesWyeApparentPower.
1.3.6.1.2.1.230.1.1.1.6
Integer32 (0..10000) · hundredths of percent
This object indicates a percentage value, in hundredths of a percent, representing the presumed accuracy of active, reactive, and apparent power usage reporting. For example, 1010 means the reported usage is accurate to +/- 10.1 percent. This value is zero if the accuracy is unknown. ANSI and IEC define the following accuracy classes for power measurement: IEC 62053-22 & 60044-1 class 0.1, 0.2, 0.5, 1, & 3. ANSI C12.20 class 0.2 & 0.5
1.3.6.1.2.1.230.1.1.1.7
Integer32 · watts
A measured value of the actual power delivered to or consumed by the load. IEC 61850-7-4 attribute 'TotW'.
1.3.6.1.2.1.230.1.1.1.8
Integer32 · volt-amperes reactive
A measured value of the reactive portion of the apparent power. IEC 61850-7-4 attribute 'TotVAr'.
1.3.6.1.2.1.230.1.1.1.9
Integer32 · volt-amperes
A measured value of the voltage and current that determines the apparent power. The apparent power is the vector sum of real and reactive power. Note: watts and volt-amperes are equivalent units and may be combined. IEC 61850-7-4 attribute 'TotVA'.
1.3.6.1.2.1.230.1.1.1.10
Integer32 (-10000..10000) · hundredths
A measured value ratio of the real power flowing to the load versus the apparent power. It is dimensionless and expressed here as a percentage value in hundredths. A power factor of 100% indicates there is no inductance load and thus no reactive power. A Power Factor can be positive or negative, where the sign should be in lead/lag (IEEE) form. IEC 61850-7-4 attribute 'TotPF'.
1.3.6.1.2.1.230.1.1.1.11
Integer32 (0..10000) · hundredths of percent
A calculated value for the current total harmonic distortion (THD). Method of calculation is not specified. IEC 61850-7-4 attribute 'ThdAmp'.
1.3.6.1.2.1.230.1.1.1.12
Integer32 (0..10000) · hundredths of percent
A calculated value for the voltage total harmonic distortion (THD). The method of calculation is not specified. IEC 61850-7-4 attribute 'ThdVol'.
1.3.6.1.2.1.230.1.2
Index: entPhysicalIndex · eoACPwrAttributesDelPhaseIndex
This optional table describes three-phase power attributes measurements in a DEL configuration with phase-to-phase power attributes measurements. Entities having single phase power shall not have any entities. This is a sparse extension of the eoACPwrAttributesTable. These attributes correspond to measurements related to the IEC 61850-7.4 MMXU phase and measured harmonic or interharmonics related to the MHAI phase.
from ENTITY-MIB
PhysicalIndexAn arbitrary value that uniquely identifies the physical entity. The value should be a small positive integer. Index values for different physical entities are not necessarily contiguous. (1..2147483647) · Integer32 · hint d
The index for this entry.
1.3.6.1.2.1.230.1.2.1.1
Integer32 (0..359)
A phase angle typically corresponding to 0, 120, 240.
1.3.6.1.2.1.230.1.2.1.2
Integer32 · 0.1 Volt AC
A measured value of phase to next phase voltages, where the next phase is IEC 61850-7-4 attribute 'PPV'.
1.3.6.1.2.1.230.1.2.1.3
Integer32 (0..10000) · hundredths of percent
A calculated value for the voltage total harmonic distortion for phase to next phase. Method of calculation is not specified. IEC 61850-7-4 attribute 'ThdPPV'.
1.3.6.1.2.1.230.1.3
Index: entPhysicalIndex · eoACPwrAttributesWyePhaseIndex
This optional table describes three-phase power attributes measurements in a WYE configuration with phase-to-neutral power attributes measurements. Entities having single phase power shall not have any entities. This is a sparse extension of the eoACPwrAttributesTable. These attributes correspond to measurements related to the IEC 61850-7.4 MMXU phase and measured harmonic or interharmonics related to the MHAI phase.
from ENTITY-MIB
PhysicalIndexAn arbitrary value that uniquely identifies the physical entity. The value should be a small positive integer. Index values for different physical entities are not necessarily contiguous. (1..2147483647) · Integer32 · hint d
The index for this entry.
1.3.6.1.2.1.230.1.3.1.1
Integer32 (0..359)
A phase angle typically corresponding to 0, 120, 240.
1.3.6.1.2.1.230.1.3.1.2
Integer32 · 0.1 Volt AC
A measured value of phase to neutral voltage. IEC 61850-7-4 attribute 'PNV'.
1.3.6.1.2.1.230.1.3.1.3
Integer32 · 0.1 amperes AC
A measured value of phase currents. IEC 61850-7-4 attribute 'A'.
1.3.6.1.2.1.230.1.3.1.4
Integer32 · watts
A measured value of the actual power delivered to or consumed by the load with the magnitude indicated separately in eoPowerUnitMultiplier. IEC 61850-7-4 attribute 'W'.
1.3.6.1.2.1.230.1.3.1.5
Integer32 · volt-amperes reactive
A measured value of the reactive portion of the apparent power with the magnitude of indicated separately in eoPowerUnitMultiplier. IEC 61850-7-4 attribute 'VAr'.
1.3.6.1.2.1.230.1.3.1.6
Integer32 · volt-amperes
A measured value of the voltage and current determines the apparent power with the indicated separately in eoPowerUnitMultiplier. Active plus reactive power equals the total apparent power. Note: Watts and volt-amperes are equivalent units and may be combined. IEC 61850-7-4 attribute 'VA'.
1.3.6.1.2.1.230.1.3.1.7
Integer32 (-10000..10000) · hundredths
A measured value ratio of the real power flowing to the load versus the apparent power for this phase. IEC 61850-7-4 attribute 'PF'. Power Factor can be positive or negative where the sign should be in lead/lag (IEEE) form.
1.3.6.1.2.1.230.1.3.1.8
Integer32 (0..10000) · hundredths of percent
A calculated value for the voltage total harmonic distortion (THD) for phase to phase. Method of calculation is not specified. IEC 61850-7-4 attribute 'ThdA'.
1.3.6.1.2.1.230.1.3.1.9
Integer32 (0..10000) · hundredths of percent
A calculated value of the voltage total harmonic distortion (THD) for phase to neutral. IEC 61850-7-4 attribute 'ThdPhV'.