T11-FC-FABRIC-CONFIG-SERVER-MIB

T11FabricIndexA Fabric Index that is used as a unique index value to identify a particular Fabric within one (or more) physical infrastructures. In an environment that is conformant to FC-SW-3, where there is always exactly one Fabric in a single physical infrastructure, the value of this Fabric Index will always be 1. However, the current standard, FC-SW-4, defines how multiple Fabrics, each with its own management instrumentation, could operate within one (or more) physical infrastructures. When such multiple Fabrics are in use, this index value is used to uniquely identify a particular Fabric within a physical infrastructure. Note that the value of this textual convention has a range of (0..4095) so as to be consistent with FC-SW-4, which says that a 'VF_ID Bitmap' is 512 bytes long, with the high-order bit representing VF_ID zero, and the low-order bit representing 4095.Reference: Fibre Channel - Switch Fabric - 4 (FC-SW-4), ANSI INCITS 418-2006, section 6.1.27.2.4. (0..4095) · Unsigned32 · hint d

The discovery by a particular switch operates within all existing Fabrics that have a Fabric Index within a specific inclusive range. This object specifies the minimum Fabric Index value within that range. This value just represents the lower end of the range and does not necessarily represent any existing Fabric.

T11FabricIndexA Fabric Index that is used as a unique index value to identify a particular Fabric within one (or more) physical infrastructures. In an environment that is conformant to FC-SW-3, where there is always exactly one Fabric in a single physical infrastructure, the value of this Fabric Index will always be 1. However, the current standard, FC-SW-4, defines how multiple Fabrics, each with its own management instrumentation, could operate within one (or more) physical infrastructures. When such multiple Fabrics are in use, this index value is used to uniquely identify a particular Fabric within a physical infrastructure. Note that the value of this textual convention has a range of (0..4095) so as to be consistent with FC-SW-4, which says that a 'VF_ID Bitmap' is 512 bytes long, with the high-order bit representing VF_ID zero, and the low-order bit representing 4095.Reference: Fibre Channel - Switch Fabric - 4 (FC-SW-4), ANSI INCITS 418-2006, section 6.1.27.2.4. (0..4095) · Unsigned32 · hint d

The discovery by a particular switch operates within all existing Fabrics that have a Fabric Index within a specific inclusive range. This object specifies the maximum Fabric Index value within that range. This value just represents the higher end of the range and does not necessarily represent any existing Fabric.

INTEGER1 = start2 = noOp · Integer32

This object provides the capability to trigger the start of a discovery by a Fabric Configuration Server. If this object is set to 'start', then the discovery is started on those Fabrics that have their Fabric Index value in the range specified by t11FcsFabricDiscoveryRangeLow and t11FcsFabricDiscoveryRangeHigh. It is recommended that whenever an instance of this object is set to 'start', that the desired range be specified at the same time by setting the corresponding instances of t11FcsFabricDiscoveryRangeLow and t11FcsFabricDiscoveryRangeHigh. Setting this object to 'start' will be rejected if a discovery is already/still in progress on any Fabrics in the specified range. No action is taken if this object is set to 'noOp'. The value of this object when read is always 'noOp'.

Unsigned32 (300..86400) · Seconds

The minimum interval of time for which the discovered Fabric information is cached by a Fabric Configuration Server.

T11FabricIndexA Fabric Index that is used as a unique index value to identify a particular Fabric within one (or more) physical infrastructures. In an environment that is conformant to FC-SW-3, where there is always exactly one Fabric in a single physical infrastructure, the value of this Fabric Index will always be 1. However, the current standard, FC-SW-4, defines how multiple Fabrics, each with its own management instrumentation, could operate within one (or more) physical infrastructures. When such multiple Fabrics are in use, this index value is used to uniquely identify a particular Fabric within a physical infrastructure. Note that the value of this textual convention has a range of (0..4095) so as to be consistent with FC-SW-4, which says that a 'VF_ID Bitmap' is 512 bytes long, with the high-order bit representing VF_ID zero, and the low-order bit representing 4095.Reference: Fibre Channel - Switch Fabric - 4 (FC-SW-4), ANSI INCITS 418-2006, section 6.1.27.2.4. (0..4095) · Unsigned32 · hint d

A unique index value that uniquely identifies a particular Fabric. In a Fabric conformant to FC-SW-4, multiple Virtual Fabrics can operate within one (or more) physical infrastructures, and this index value is used to uniquely identify a particular (physical or virtual) Fabric within a physical infrastructure. In a Fabric conformant to versions earlier than FC-SW-4, only a single Fabric could operate within a physical infrastructure, and thus, the value of this Fabric Index was defined to always be 1.

INTEGER1 = inProgress2 = completed3 = localOnly · Integer32

The status of the discovery for the particular Fabric. Initially when the switch comes up, all instances of this object have the value: 'localOnly', and the database contains only local information, i.e., no information discovered via the Fabric Configuration Server protocol specified in FC-GS-5. If t11FcsFabricDiscoveryStart is set to 'start' for a range of Fabrics that includes this Fabric, then the value of this object transitions to 'inProgress'. When the discovery completes, this object transitions to 'completed', and the data is cached for the minimum interval of time specified by t11FcsFabricDiscoveryTimeOut. After this interval has been exceeded, the data may be lost, in which case, the value of this object changes to 'localOnly'. This object cannot be set via SNMP to any value other than 'localOnly'. If this object is set (via SNMP) to 'localOnly', the cached data for the Fabric is discarded immediately, and if a discovery initiated from this switch was in progress for this Fabric, then that discovery is aborted.

TimeStampThe value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset to zero as a result of a re- initialization of the network management (sub)system, then the values of all TimeStamp objects are also reset. However, after approximately 497 days without a re- initialization, the sysUpTime object will reach 2^^32-1 and then increment around to zero; in this case, existing values of TimeStamp objects do not change. This can lead to ambiguities in the value of TimeStamp objects. · TimeTicks

This object contains the value of sysUpTime at which discovery was most recently completed or aborted on this Fabric. This object contains the value of zero before the first discovery on this Fabric.

FcNameIdOrZeroThe World Wide Name (WWN) associated with a Fibre Channel (FC) entity. WWNs were initially defined as 64-bits in length. The latest definition (for future use) is 128-bits long. The zero-length string value is used in circumstances in which the WWN is unassigned/unknown. SIZE (8 | 16) · OCTET STRING

The WWN of an Interconnect Element. This object uniquely identifies an Interconnect Element on a Fabric. If the IE is a switch, then this object is the Switch_Name (WWN) of the switch. ⓘ

T11FcIeType1 = unknown2 = other3 = switch4 = hub5 = bridgeThe type of Interconnect Element (IE): unknown(1) - an unknown IE. other(2) - some other type of IE. switch(3) - the IE is a switch. hub(4) - the IE is a hub. bridge(5) - the IE is a bridge.Reference: ANSI INCITS 427-2007, Fibre Channel - Generic Services 5, FC-GS-5, Table 96. · Integer32

The type of this Interconnect Element. ⓘ

FcDomainIdOrZeroThe Domain Id (of an FC switch), or zero if the no Domain Id has been assigned. (0..239) · Integer32

The Domain ID of this Interconnect Element. ⓘ

FcAddressIdOrZeroA Fibre Channel Address ID, a 24-bit value unique within the address space of a Fabric. The zero-length string value is used in circumstances in which the WWN is unassigned/unknown. SIZE (0 | 3) · OCTET STRING

The management identifier of this Interconnect Element. If the Interconnect Element is a switch, this object will be the Domain Controller identifier of the switch. When the value of the identifier is unknown, this object contains the all-zeros value: x'00 00 00'. ⓘ

FcNameIdOrZeroThe World Wide Name (WWN) associated with a Fibre Channel (FC) entity. WWNs were initially defined as 64-bits in length. The latest definition (for future use) is 128-bits long. The zero-length string value is used in circumstances in which the WWN is unassigned/unknown. SIZE (8 | 16) · OCTET STRING

The Fabric_Name (WWN) of this Interconnect Element. When the Fabric_Name is unknown, this object contains the all-zeros value: x'00 00 00 00 00 00 00 00'. ⓘ

OCTET STRING SIZE (0..255)

The logical name of this Interconnect Element. When the logical name is unknown, this object contains the zero-length string. ⓘ

T11FcListIndexPointerOrZeroObjects with this syntax point to a list of elements contained in a table, by holding the same value as the object with syntax T11FcListIndex defined in the table's INDEX clause, or, zero to indicate an empty list. Note that such a table could have one row per list, or it could have one row per element of a list. The definition of an object with this syntax must identify the table(s) into which it points. · Unsigned32 · hint d

The management address list for this Interconnect Element. This object points to an entry in the t11FcsMgmtAddrListTable. ⓘ

OCTET STRING SIZE (0..252)

The information list for this Interconnect Element. The value of this object is formatted as specified in FC-GS-5, i.e., it has the following substrings in order: vendor name, model name/number, and release code/level, followed by zero or more substrings of vendor-specific information. Each substring is terminated with a byte containing a null value (x'00'). ⓘ

T11FcListIndexAn index that identifies a list of elements. All elements that belong to the same list have the same index value. This syntax is used for objects which identify a list in the INDEX clause of a table of elements of that type of list. (1..4294967295) · Unsigned32 · hint d

The index value of the management address list.

Unsigned32 (1..4294967295)

An integer value to distinguish different management addresses in the same list.

URLStringA Uniform Resource Locator represented in accordance with RFCs 1738 and 2368, presented in the NVT ASCII charset defined in RFC 854. SIZE (0..255) · OCTET STRING · hint 255a

The management address of this entry. The format of this object is a Uniform Resource Locator (URL), e.g., for SNMP, see RFC 4088. ⓘ

FcNameIdOrZeroThe World Wide Name (WWN) associated with a Fibre Channel (FC) entity. WWNs were initially defined as 64-bits in length. The latest definition (for future use) is 128-bits long. The zero-length string value is used in circumstances in which the WWN is unassigned/unknown. SIZE (8 | 16) · OCTET STRING

The Port_Name (WWN) of the port for which this row contains information. ⓘ

FcPortTypeThe type of a Fibre Channel port, as indicated by the use of the appropriate value assigned by IANA.Reference: The IANA-maintained registry for Fibre Channel port types (http://www.iana.org/). · Unsigned32

The Port Type of this port. ⓘ

T11FcPortTxType1 = unknown2 = other3 = shortwave850nm4 = longwave1550nm5 = longwave1310nm6 = electrical7 = tenGbaseSr8508 = tenGbaseLr13109 = tenGbaseEr155010 = tenGbaseLx130011 = tenGbaseSw85012 = tenGbaseLw131013 = tenGbaseEw1550The technology of the port transceiver: unknown(1) - unknown (includes the 'null' type) other(2) - some other technology shortwave850nm(3) - Short wave laser - SN (850 nm) longwave1550nm(4) - Long wave laser - LL (1550 nm) longwave1310nm(5) - Long wave laser cost reduced - LC (1310 nm) electrical(6) - Electrical - EL. tenGbaseSr850(7) - 10GBASE-SR 850nm laser tenGbaseLr1310(8) - 10GBASE-LR 1310nm laser tenGbaseEr1550(9) - 10GBASE-ER 1550nm laser tenGbaseLx1300(10) - 10GBASE-LX4 WWDM 1300nm laser tenGbaseSw850(11) - 10GBASE-SW 850nm laser tenGbaseLw1310(12) - 10GBASE-LW 1310nm laser tenGbaseEw1550(13) - 10GBASE-EW 1550nm laserReference: ANSI INCITS 427-2007, Fibre Channel - Generic Services 5, FC-GS-5, Table 101. · Integer32

The Port TX Type of this port. ⓘ

Unsigned32 (0..255)

The port module type of this port. ⓘ

Unsigned32

The physical number for this port. FC-GS-5 says that the contents of this field, which are carried in a field with a size of 4 bytes, are not to be restricted due to vendor-specific methods for numbering physical ports. ⓘ

T11FcListIndexPointerOrZeroObjects with this syntax point to a list of elements contained in a table, by holding the same value as the object with syntax T11FcListIndex defined in the table's INDEX clause, or, zero to indicate an empty list. Note that such a table could have one row per list, or it could have one row per element of a list. The definition of an object with this syntax must identify the table(s) into which it points. · Unsigned32 · hint d

The attached port name list for this port. This object points to an entry in the t11FcsAttachPortNameListTable. ⓘ

T11FcPortState1 = unknown2 = other3 = online4 = offline5 = testing6 = faultThe state of a port: unknown(1) - unknown state. other(2) - some other state. online(3) - port is in online state. offline(4) - port is in offline state. testing(5) - port is in testing state. fault(6) - port is faulty.Reference: ANSI INCITS 427-2007, Fibre Channel - Generic Services 5, FC-GS-5, Table 106. · Integer32

The state of this port. ⓘ

OCTET STRING SIZE (2)

The port speed capabilities of this port. The two octets of the value are formatted as described in FC-GS-5. ⓘ

OCTET STRING SIZE (2)

The operating speed of this port. The two octets of the value are formatted as described in FC-GS-5. ⓘ

OCTET STRING SIZE (12)

The zoning enforcement status of this port. The 12 octets of the value are formatted as described in FC-GS-5. ⓘ

T11FcListIndexAn index that identifies a list of elements. All elements that belong to the same list have the same index value. This syntax is used for objects which identify a list in the INDEX clause of a table of elements of that type of list. (1..4294967295) · Unsigned32 · hint d

The index value of the attach port name list.

OCTET STRING SIZE (12)

The attached port name. Zero or more of these names may be associated with a port object. The first 8 bytes of this object contain the WWN of the port followed by 2 reserved bytes. Following this is one byte of Port flags and one byte of Port type, as described in FC-GS-5. ⓘ

Unsigned32 (1..4294967295)

An integer value to distinguish one platform from other platforms in the same Fabric.

OCTET STRING SIZE (1..255)

The name of this platform. The last byte of the value indicates the format of the name (even if the name itself is the zero-length string) as specified in FC-GS-5. ⓘ

OCTET STRING SIZE (4)

The type(s) of this platform, encoded in 4 bytes as specified in FC-GS-5. ⓘ

T11FcListIndexPointerOrZeroObjects with this syntax point to a list of elements contained in a table, by holding the same value as the object with syntax T11FcListIndex defined in the table's INDEX clause, or, zero to indicate an empty list. Note that such a table could have one row per list, or it could have one row per element of a list. The definition of an object with this syntax must identify the table(s) into which it points. · Unsigned32 · hint d

The list of nodes for this platform. This object points to an entry in the t11FcsNodeNameListTable. ⓘ

T11FcListIndexPointerOrZeroObjects with this syntax point to a list of elements contained in a table, by holding the same value as the object with syntax T11FcListIndex defined in the table's INDEX clause, or, zero to indicate an empty list. Note that such a table could have one row per list, or it could have one row per element of a list. The definition of an object with this syntax must identify the table(s) into which it points. · Unsigned32 · hint d

The list of management addresses for this platform. This object points to an entry in the t11FcsMgmtAddrListTable. ⓘ

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0 | 12) · OCTET STRING · hint 255t

The identifier of the vendor of this platform, in the format specified in FC-GS-5. ⓘ

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0 | 20) · OCTET STRING · hint 255t

The vendor's product and/or model identifier for this platform, in the format specified in FC-GS-5. ⓘ

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0 | 4..32) · OCTET STRING · hint 255t

The product revision level for this platform, in the format specified in FC-GS-5. ⓘ

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0 | 4..128) · OCTET STRING · hint 255t

The description of this platform, in the format specified in FC-GS-5. This value should include the full name and version identification of the platform's hardware type and software operating system. ⓘ

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0 | 4..64) · OCTET STRING · hint 255t

An administratively assigned symbolic name for the platform, in the format specified in FC-GS-5. ⓘ

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0 | 4..128) · OCTET STRING · hint 255t

The physical location of the platform, in the format specified in FC-GS-5 (e.g., 'telephone closet, 3rd floor'). ⓘ

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0 | 4..64) · OCTET STRING · hint 255t

An identifier for a hosting system that this platform is associated with. This identifier is used to associate platforms of logical types (e.g., logical partitions) with a physical system. ⓘ

T11FcListIndexPointerOrZeroObjects with this syntax point to a list of elements contained in a table, by holding the same value as the object with syntax T11FcListIndex defined in the table's INDEX clause, or, zero to indicate an empty list. Note that such a table could have one row per list, or it could have one row per element of a list. The definition of an object with this syntax must identify the table(s) into which it points. · Unsigned32 · hint d

A list of management addresses for the platform. ⓘ

SnmpAdminStringAn octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC3416]. Note that the size of an SnmpAdminString object is measured in octets, not characters. SIZE (0 | 4..64) · OCTET STRING · hint 255t

An identifier for a cluster that this platform is associated with, where a cluster is a set of independent platforms that are managed together to provide increased performance capabilities, failover, etc. ⓘ

T11FcListIndexPointerOrZeroObjects with this syntax point to a list of elements contained in a table, by holding the same value as the object with syntax T11FcListIndex defined in the table's INDEX clause, or, zero to indicate an empty list. Note that such a table could have one row per list, or it could have one row per element of a list. The definition of an object with this syntax must identify the table(s) into which it points. · Unsigned32 · hint d

A list of management addresses for the cluster identified in the corresponding instance of t11FcsPlatformClusterId. ⓘ

OCTET STRING SIZE (0 | 32)

The FC-4 types supported by this platform, formatted as a bit mask as specified in FC-GS-5. If this object contains the zero-length string, the types are unknown. ⓘ

T11FcListIndexAn index that identifies a list of elements. All elements that belong to the same list have the same index value. This syntax is used for objects which identify a list in the INDEX clause of a table of elements of that type of list. (1..4294967295) · Unsigned32 · hint d

The index value of the node name list.

FcNameIdOrZeroThe World Wide Name (WWN) associated with a Fibre Channel (FC) entity. WWNs were initially defined as 64-bits in length. The latest definition (for future use) is 128-bits long. The zero-length string value is used in circumstances in which the WWN is unassigned/unknown. SIZE (8 | 16) · OCTET STRING

The name of this node.

Counter32

The number of Get Requests received by the Fabric Configuration Server on this Fabric. This counter has no discontinuities other than those that all Counter32s have when sysUpTime=0.

Counter32

The number of Get Requests sent by the Fabric Configuration Server on this Fabric to other servers in the Fabric. This counter has no discontinuities other than those that all Counter32s have when sysUpTime=0.

Counter32

The number of Registration Requests received by the Fabric Configuration Server on this Fabric. This counter has no discontinuities other than those that all Counter32s have when sysUpTime=0.

Counter32

The number of Registration Requests sent by the Fabric Configuration Server on this Fabric. This counter has no discontinuities other than those that all Counter32s have when sysUpTime=0.

Counter32

The number of Deregistration Requests received by the Fabric Configuration Server on this Fabric. This counter has no discontinuities other than those that all Counter32s have when sysUpTime=0.

Counter32

The number of Deregistration Requests sent by the Fabric Configuration Server on this Fabric. This counter has no discontinuities other than those that all Counter32s have when sysUpTime=0.

Counter32

The total number of requests rejected by the Fabric Configuration Server on this Fabric. This counter has no discontinuities other than those that all Counter32s have when sysUpTime=0.

TruthValue1 = true2 = falseRepresents a boolean value. · Integer32

This object specifies if the Fabric Configuration Server should generate 't11FcsRqRejectNotification' notifications. If the value of this object is 'true', then the notification is issued. If the value of this object is 'false', then the notification is not issued.

TruthValue1 = true2 = falseRepresents a boolean value. · Integer32

This object specifies if the Fabric Configuration Server should generate 't11FcsDiscoveryCompleteNotify' notifications. If the value of this object is 'true', then the notification is issued. If the value of this object is 'false', then the notification is not issued.

TruthValue1 = true2 = falseRepresents a boolean value. · Integer32

This object specifies if the Fabric Configuration Server should generate 't11FcsMgmtAddrChangeNotify' notifications. If the value of this object is 'true', then the notification is issued. If the value of this object is 'false', then the notification is not issued.

OCTET STRING SIZE (0..255)

The binary content of the Fabric Configuration Server request, formatted as an octet string (in network byte order) containing the Common Transport Information Unit (CT_IU), as described in Table 2 of FC-GS-5 (including the preamble), which was most recently rejected by the Fabric Configuration Server for this Fabric. This object contains the zero-length string if and when the CT-IU's content is unavailable. When the length of this object is 255 octets, it contains the first 255 octets of the CT-IU (in network byte order).

FcNameIdOrZeroThe World Wide Name (WWN) associated with a Fibre Channel (FC) entity. WWNs were initially defined as 64-bits in length. The latest definition (for future use) is 128-bits long. The zero-length string value is used in circumstances in which the WWN is unassigned/unknown. SIZE (0 | 8 | 16) · OCTET STRING

The WWN that was the source of the CT_IU contained in the corresponding instance of t11FcsRejectCtCommandString.

T11NsGs4RejectReasonCode1 = none2 = invalidCmdCode3 = invalidVerLevel4 = logicalError5 = invalidIUSize6 = logicalBusy7 = protocolError8 = unableToPerformCmdReq9 = cmdNotSupported10 = serverNotAvailable11 = couldNotEstabSession12 = vendorErrorThe FC-GS-4 reject reason code for a request. none(1) - no error. invalidCmdCode(2) - request contained an invalid command code. invalidVerLevel(3) - request contained an invalid version number. logicalError(4) - there was a logical error. invalidIUSize(5) - the CT_IU (Information Unit) size was invalid. logicalBusy(6) - the module is busy. protocolError(7) - there was a protocol error. unableToPerformCmdReq(8) - the command specified in the req could not be executed. The details of exactly what failed will be in the corresponding reason code explanation. cmdNotSupported(9) - the command is not supported. serverNotAvailable(10) - the identified server was not available. couldNotEstabSession(11) - a server session could not be established. vendorError(12) - a vendor-specific error.Reference: ANSI INCITS 387-2004, Fibre Channel - Generic Services-4 (FC-GS-4), section 4.4.3. · Integer32

This object contains the reason code corresponding to the latest Fabric Configuration Server request rejected by the local system.

T11FcsRejectReasonExplanation1 = noAdditionalExplanation2 = invNameIdForIEOrPort3 = ieListNotAvailable4 = ieTypeNotAvailable5 = domainIdNotAvailable6 = mgmtIdNotAvailable7 = fabNameNotAvailable8 = ielogNameNotAvailable9 = mgmtAddrListNotAvailable10 = ieInfoListNotAvailable11 = portListNotAvailable12 = portTypeNotAvailable13 = phyPortNumNotAvailable14 = attPortNameListNotAvailable15 = portStateNotAvailable16 = unableToRegIELogName17 = platformNameNoExist18 = platformNameAlreadyExists19 = platformNodeNameNoExists20 = platformNodeNameAlreadyExists21 = resourceUnavailable22 = noEntriesInLunMap23 = invalidDeviceNameLength24 = multipleAttributes25 = invalidAttribBlockLength26 = attributesMissingThe reject reason code explanation: noAdditionalExplanation(1) - no additional explanation. invNameIdForIEOrPort(2) - the format of IE or port name is invalid. ieListNotAvailable(3) - IE list is not available. ieTypeNotAvailable(4) - IE type is not available. domainIdNotAvailable(5) - Domain ID is not available. mgmtIdNotAvailable(6) - mgmt ID is not available. fabNameNotAvailable(7) - Fabric_Name is not available. ielogNameNotAvailable(8) - IE logical name is not available. mgmtAddrListNotAvailable(9) - mgmt address list is not available. ieInfoListNotAvailable(10) - IE info list is not available. portListNotAvailable(11) - port list is not available. portTypeNotAvailable(12) - port type is not available. phyPortNumNotAvailable(13) - physical port number is not available. attPortNameListNotAvailable(14) - attached port name list is not available. portStateNotAvailable(15) - port state is not available. unableToRegIELogName(16) - not able to register IE logical name. platformNameNoExist(17) - platform name does not exist. platformNameAlreadyExists(18) - platform name already exists. platformNodeNameNoExists(19) - platform node name does not exist. platformNodeNameAlreadyExists(20) - platform node name already exists. resourceUnavailable(21) - resource unavailable. noEntriesInLunMap(22) - zero entries in OS LUN Map. invalidDeviceNameLength(23) - invalid OS device name length. multipleAttributes(24) - multiple attributes of same type in platform attribute block. invalidAttribBlockLength(25) - invalid platform attribute block length. attributesMissing(26) - required platform attributes not present.Reference: ANSI INCITS 427-2007, Fibre Channel - Generic Services 5, FC-GS-5, Table 124. · Integer32

When the corresponding instance of t11FcsRejectReasonCode has the value: 'unable to perform command request', this object contains the corresponding reason code explanation.

OCTET STRING SIZE (1)

A registration reject vendor-specific code. This object contains the vendor-specific code of the most recently rejected Fabric Configuration Server Registration request for the particular port on the particular Fabric.