ciscoEnvMonSupplyStatusIndex
Integer32 (0..2147483647)
Unique index for the power supply being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning.
CISCO-ACCESS-ENVMON-MIB
1998-08-05
The MIB module to describe the additional status of the Environmental Monitor on those Cisco Access devices which support one.
Download CISCO-ACCESS-ENVMON-MIB.txt Open CISCO-ACCESS-ENVMON-MIB.txt in a new tab
Tables (1)
| Name | OID |
|---|---|
| caemSupplyStatusTableaugments ciscoEnvMonSupplyStatusTable (CISCO-ENVMON-MIB) | 1.3.6.1.4.1.9.9.61.1.1 |
Traps (2)
| Name | OID |
|---|---|
| caemTemperatureNotification | 1.3.6.1.4.1.9.9.61.2.0.1 |
| caemVoltageNotification | 1.3.6.1.4.1.9.9.61.2.0.2 |
END OF TOC
Table details
caemSupplyStatusTable
1.3.6.1.4.1.9.9.61.1.1
augments ciscoEnvMonSupplyStatusTable (CISCO-ENVMON-MIB)
Index: ciscoEnvMonSupplyStatusIndex
The table contains the additional power supply information that are not covered in the ciscoEnvMonSupplyStatusTable of CISCO-ENVMON-MIB.
from CISCO-ENVMON-MIB
caemSupplyFailedComponent
1.3.6.1.4.1.9.9.61.1.1.1.1
INTEGER1 = none2 = inputVoltage3 = dcOutputVoltage4 = thermal5 = multiple6 = fan7 = overvoltage · Integer32
The failure component of the power supply being instrumented. none - No failure. inputVoltage - Input power lost in one of the power supplies dcOutputVoltage - DC output voltage lost in one of the power supplies thermal - Power supply thermal failure. multiple - Multiple failures. fan - Fan failure overvoltage - Over voltage.
Trap details
caemTemperatureNotification
1.3.6.1.4.1.9.9.61.2.0.1
A caemTemperatureNotification is sent if the over temperature condition is detected in the managed system. This is a replacement for the ciscoEnvMonTemperatureNotification trap because the information 'ciscoEnvMonTemperatureStatusValue' required by the trap is not available in the managed system.
ciscoEnvMonTemperatureStatusDescr
1.3.6.1.4.1.9.9.13.1.3.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..32) · OCTET STRING · hint 255a
Textual description of the testpoint being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry.
ciscoEnvMonTemperatureState
1.3.6.1.4.1.9.9.13.1.3.1.6
CiscoEnvMonState1 = normal2 = warning3 = critical4 = shutdown5 = notPresent6 = notFunctioningRepresents the state of a device being monitored. Valid values are: normal(1): the environment is good, such as low temperature. warning(2): the environment is bad, such as temperature above normal operation range but not too high. critical(3): the environment is very bad, such as temperature much higher than normal operation limit. shutdown(4): the environment is the worst, the system should be shutdown immediately. notPresent(5): the environmental monitor is not present, such as temperature sensors do not exist. notFunctioning(6): the environmental monitor does not function properly, such as a temperature sensor generates a abnormal data like 1000 C. · Integer32
The current state of the testpoint being instrumented.
caemVoltageNotification
1.3.6.1.4.1.9.9.61.2.0.2
A caemVoltageNotification is sent if the over voltage condition is detected and ciscoEnvMonVoltageState is not set to 'notPresent' in the managed system. This is a replacement for the ciscoEnvMonVoltageNotification trap because the information 'ciscoEnvMonVoltageStatusValue' required by the trap is not available in the managed system.
ciscoEnvMonVoltageStatusDescr
1.3.6.1.4.1.9.9.13.1.2.1.2
DisplayStringRepresents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. SIZE (0..32) · OCTET STRING · hint 255a
Textual description of the testpoint being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry.
ciscoEnvMonVoltageState
1.3.6.1.4.1.9.9.13.1.2.1.7
CiscoEnvMonState1 = normal2 = warning3 = critical4 = shutdown5 = notPresent6 = notFunctioningRepresents the state of a device being monitored. Valid values are: normal(1): the environment is good, such as low temperature. warning(2): the environment is bad, such as temperature above normal operation range but not too high. critical(3): the environment is very bad, such as temperature much higher than normal operation limit. shutdown(4): the environment is the worst, the system should be shutdown immediately. notPresent(5): the environmental monitor is not present, such as temperature sensors do not exist. notFunctioning(6): the environmental monitor does not function properly, such as a temperature sensor generates a abnormal data like 1000 C. · Integer32
The current state of the testpoint being instrumented.