1997-02-19
This is the MIB module for objects used to manage FRAS sessions to the endstation. These objects are specific to downstream or enduster sessions only. It does not contain objects supported by the FRAS-HOST MIB which are specific to upstream or host-end sessions.
Download CISCO-DLC-SWITCH-MIB.txt Open CISCO-DLC-SWITCH-MIB.txt in a new tab
| Name | OID |
|---|---|
| frasBnnSdlcConTable | 1.3.6.1.4.1.9.9.76.1.1.1 |
| frasBnnLlcConTable | 1.3.6.1.4.1.9.9.76.1.2.1 |
| frasBanSdlcConTable | 1.3.6.1.4.1.9.9.76.1.3.1 |
| frasBanLlcConTable | 1.3.6.1.4.1.9.9.76.1.4.1 |
END OF TOC
1.3.6.1.4.1.9.9.76.1.1.1
Index: ifIndex · bnnSdlcConAddress
This table contains mapping information for each SDLC Link Station in a FRAS-BNN to SDLC connection. All entries are derived entirely from the router configuration.
from RFC1213-MIB
INTEGER · Integer32
A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.76.1.1.1.1.1
SdlcAddressA hexadecimal address assigned to a secondary poll station of an SDLC device. SIZE (1) · OCTET STRING
This value is the poll address of the secondary link station for this SDLC link. It uniquely identifies the SDLC link station within a single SDLC port.
1.3.6.1.4.1.9.9.76.1.1.1.1.2
INTEGER1 = reset2 = testSent3 = xidexchg4 = connrqsent5 = sigstnwait6 = connrspwait7 = connrspsent8 = contacted9 = discwait · Integer32
Contains the FRAS state of the Link Station. reset - no activity testSent - TEST Frames sent xidexchg - XID exchange in progress connrqsent - Connect request sent sigstnwait - Signal station wait state connrspwait - Connect response wait state connrspsent - Connect response sent contacted - Session established discwait - Disconnect wait state
1.3.6.1.4.1.9.9.76.1.1.1.1.3
Integer32 (16..1022)
The Data Link Connection Identifier used for this particular connection.
1.3.6.1.4.1.9.9.76.1.1.1.1.4
InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d
This is the Frame-Relay interface which the SDLC Link Station is using to connect to the Host.
1.3.6.1.4.1.9.9.76.1.1.1.1.5
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The Local SAP for this SDLC station's corresponding LLC session to the host.
1.3.6.1.4.1.9.9.76.1.1.1.1.6
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The Remote SAP for this SDLC station's corresponding LLC session to the host.
1.3.6.1.4.1.9.9.76.1.2.1
Index: ifIndex · bnnLlcConDeviceMacAddress · bnnLlcConLanLocalSap · bnnLlcConLanRemoteSap
This table contains information for each End Station in a FRAS-BNN to LLC connection. The entries are derived entirely from the router configuration.
from RFC1213-MIB
INTEGER · Integer32
A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.76.1.2.1.1.1
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
This value is the End Station's Local Mac-Address.
1.3.6.1.4.1.9.9.76.1.2.1.1.2
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The End Station's Local SAP.
1.3.6.1.4.1.9.9.76.1.2.1.1.3
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The End Station's Remote SAP.
1.3.6.1.4.1.9.9.76.1.2.1.1.4
InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d
This is the physical interace which the End Station is attached to.
1.3.6.1.4.1.9.9.76.1.2.1.1.5
Integer32 (16..1022)
The Data Link Connection Identifier associated with the corresponding LLC2 session over Frame-Relay to the host.
1.3.6.1.4.1.9.9.76.1.2.1.1.6
INTEGER1 = reset2 = testSent3 = xidexchg4 = connrqsent5 = sigstnwait6 = connrspwait7 = connrspsent8 = contacted9 = discwait · Integer32
Contains the FRAS state of the Link Station. reset - no activity testSent - TEST Frames sent xidexchg - XID exchange in progress connrqsent - Connect request sent sigstnwait - Signal station wait state connrspwait - Connect response wait state connrspsent - Connect response sent contacted - Session established discwait - Disconnect wait state
1.3.6.1.4.1.9.9.76.1.2.1.1.7
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
The Mac-Address configured as the End Station's target or Remote address.
1.3.6.1.4.1.9.9.76.1.2.1.1.8
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The FRAS router's Local SAP.
1.3.6.1.4.1.9.9.76.1.2.1.1.9
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The FRAS router's Remote SAP.
1.3.6.1.4.1.9.9.76.1.3.1
Index: ifIndex · banSdlcConAddress · banSdlcConBanDlciMac
This table contains information for each SDLC Link Station in a FRAS-BAN to SDLC connection. The entries are derived entirely from the router configuration.
from RFC1213-MIB
INTEGER · Integer32
A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
1.3.6.1.4.1.9.9.76.1.3.1.1.1
InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d
This is the physical interface the SDLC Link Stations are connected to.
1.3.6.1.4.1.9.9.76.1.3.1.1.2
SdlcAddressA hexadecimal address assigned to a secondary poll station of an SDLC device. SIZE (1) · OCTET STRING
This value is the poll address of the secondary link station for this SDLC link. It uniquely identifies the SDLC link station within a single SDLC port.
1.3.6.1.4.1.9.9.76.1.3.1.1.3
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
The End Station's target or Remote mac-address.
1.3.6.1.4.1.9.9.76.1.3.1.1.4
Integer32 (16..1022)
The Data Link Connection Identifier for the corresponding LLC2 session over Frame-Relay to the host.
1.3.6.1.4.1.9.9.76.1.3.1.1.5
INTEGER1 = reset2 = testSent3 = xidexchg4 = connrqsent5 = sigstnwait6 = connrspwait7 = connrspsent8 = contacted9 = discwait · Integer32
Contains the FRAS state of the Link Station. reset - no activity testSent- TEST Frames sent xidexchg - XID exchange in progress connrqsent - Connect request sent sigstnwait - Signal station wait state connrspwait - Connect response wait state connrspsent - Connect response sent contacted - Session established discwait - Disconnect wait state
1.3.6.1.4.1.9.9.76.1.3.1.1.6
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
The End Station's virtual Mac-Address which is comprised of a TR formatted template and the SDLC Link Station address appended on the last nibble.
1.3.6.1.4.1.9.9.76.1.3.1.1.7
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
BNI is Boundary Node Identifier which is the FRAS-BAN connection's Remote address in TR-format. It is by default 4fff.0000.0000
1.3.6.1.4.1.9.9.76.1.3.1.1.8
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The FRAS router's Local SAP.
1.3.6.1.4.1.9.9.76.1.3.1.1.9
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The FRAS router's Remote SAP.
1.3.6.1.4.1.9.9.76.1.4.1
Index: banLlcEndstnLocalMac · banLlcConLocalSap · banLlcConRemoteSap · banLlcBanDlciMac
This table contains information for each LAN attached End Station in a FRAS-BAN to LAN connection. The entries are from endstations which have their destination mac-addresses as the BAN-DLCI-MAC address.
1.3.6.1.4.1.9.9.76.1.4.1.1.1
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
This value is the End Station's Local Mac-Address.
1.3.6.1.4.1.9.9.76.1.4.1.1.2
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
This value is the End Station's Remote Mac-Address. It is also the FRAS-BAN connection's Local Mac-Address.
1.3.6.1.4.1.9.9.76.1.4.1.1.3
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The endstation's Local SAP.
1.3.6.1.4.1.9.9.76.1.4.1.1.4
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The endstation's Remote SAP.
1.3.6.1.4.1.9.9.76.1.4.1.1.5
Integer32 (16..1022)
The Data Link Connection Identifier associated with the corresponding LLC2 session over Frame-Relay to the host.
1.3.6.1.4.1.9.9.76.1.4.1.1.6
INTEGER1 = reset2 = testSent3 = xidexchg4 = connrqsent5 = sigstnwait6 = connrspwait7 = connrspsent8 = contacted9 = discwait · Integer32
Contains the FRAS state of the Link Station. reset - no activity testSent- TEST Frames sent xidexchg - XID exchange in progress connrqsent - Connect request sent sigstnwait - Signal station wait state connrspwait - Connect response wait state connrspsent - Connect response sent contacted - Session established discwait - Disconnect wait state
1.3.6.1.4.1.9.9.76.1.4.1.1.7
InterfaceIndexOrZeroThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced. (0..2147483647) · Integer32 · hint d
This is the Frame-Relay interface for this particular session.
1.3.6.1.4.1.9.9.76.1.4.1.1.8
MacAddressRepresents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires MAC addresses to be transmitted most significant bit first. SIZE (6) · OCTET STRING · hint 1x:
This value is the FRAS-BAN connection's Target Mac-Address. It is by default 4fff.0000.0000
1.3.6.1.4.1.9.9.76.1.4.1.1.9
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The Local SAP of the corresponding LLC2 session over Frame-Relay to the host.
1.3.6.1.4.1.9.9.76.1.4.1.1.10
SAPService Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n. SIZE (1) · OCTET STRING
The Remote SAP of the corresponding LLC2 session over Frame-Relay to the host.